DMP Electronics 1134 Installation guide

INSTALLATION AND PROGRAMMING GUIDE
1134 Wireless
Wiegand Module

About the 1134 ............................................ 1
Power Supply......................................................... 1
Zone Terminals ...................................................... 1
Annunciators.......................................................... 1
LED Indicators ....................................................... 1
LED Survey ............................................................ 2
Form C Relay......................................................... 2
Programming Connection................................ 2
Dry/Wet Contact ................................................. 2
PCB Features...............................................3
Program the 1134 ........................................4
Part 1: Device Setup............................................ 4
Part 2: Zone Information .................................. 5
Install the 1134 ............................................6
Mount the 1134...................................................... 6
Wire the Electronic Lock.................................. 7
Isolation Relay ...................................................... 9
Install the 333 Suppressor ..............................10
Wire the Zone Terminals...................................11
Connect a Card Reader....................................13
TABLE OF CONTENTS
Program the 1134 Options....................... 15
Program Start Display ......................................15
Serial Number Display......................................15
Initialization Option ...........................................15
Initialize Confirm Option .................................16
Activate Zone 2 Bypass ...................................16
Zone 2 Bypass Time .......................................... 17
Relock on Zone 2 Change...............................17
Activate Zone 3 Request to Exit ..................18
Zone 3 REX Strike Time...................................19
Activate Onboard Speaker .............................19
Custom Card Definitions ........................ 20
Any Card Format...............................................20
Card Formats ......................................................20
Format Name......................................................20
Wiegand Code Length .....................................21
Site Code Position and Length ....................22
User Code Position and Length................... 22
Require Site Code .............................................22
Site Code Display ..............................................23
Number of User Code Digits.........................23

No Communication with Panel ....................24
Remove Keypad.................................................25
Public Card Formats ............................... 26
Product Specifications ............................27
Readers and Credentials .........................28
FCC Information ...................................... 30
Industry Canada Information.................. 31

Digital Monitoring Products, Inc. | 1134 Installation and Programming Guide 1
ANNUNCIATORS
An on-board programmable piezo provides local
annunciation at the 1134. You can also connect a
variety of switched ground annunciators to the
1134 for remote annunciation.
LED INDICATORS
The 1134 provides two indicator LEDs. The
SURVEY (Red) LED turns on for the same
duration as the door strike relay. The WIEGAND
(Yellow) LED turns on for one second to indicate
receipt of a valid Wiegand input.
The 1134 Wireless Wiegand Module allows you to use the powerful built-in access control capability of
DMP panels. DMP panels provide access control, arming, and disarming using proximity, mag-stripe,
biometric or other Wiegand-output authentication devices.
The 1134 connects and operates wirelessly with DMP panels. A keypad may be plugged directly into
the 1134 for local programming. The 1134 includes the following features:
POWER SUPPLY
The 1134 operates at 12/24VDC from the power
supply supporting a door’s magnetic lock or
door-strikes. It also provides a 10 Amp Form C
relay contact for lock control.
ZONE TERMINALS
The 1134 has four onboard zones that can be
programmed for a variety of burglary or access
control applications.
ABOUT THE 1134

2 1134 Installation and Programming Guide | Digital Monitoring Products, Inc.
LED SURVEY
The 1134 provides a Survey LED capability to
allow one person to confirm communication with
the wireless receiver while the cover is removed.
Mount the 1134 away from large metal objects
because it may impair performance. Do not
mount the 1134 inside a metal enclosure or install
in a drop ceiling.
1. With the cover removed, hold the 1134 in the
exact desired location.
2. Press the tamper switch to send data to the
panel and determine if communication is
confirmed or faulty.
Confirmed: If communication is
confirmed, for each press or release of the
tamper switch, the LED blinks
immediately on and immediately o.
Faulty: If communication is faulty, the
LED remains on for about 8seconds or
flashes multiple times in quick succession.
Relocate the 1134 or receiver until the LED
confirms clear communication.
FORM C RELAY
The 1134’s Form C relay draws up to 35mA of
current. Refer to the NC/C/NO (Dry Contact
Relay) and the Isolation Relay sections in this
document for more information.
PROGRAMMING CONNECTION
The 1134 provides a keypad programming
connection that allows you to use a standard
DMP LCD keypad for initial setup.
DRY/WET CONTACT
Apply power to the door relay (WET setting) or
leave it unpowered (DRY setting).

Digital Monitoring Products, Inc. | 1134 Installation and Programming Guide 3
1234 5 6 7 810 11 12 13 14
9
LC ASRED WHT GRN BLK Z1 Z2 Z3 Z4RA GND GND
NC
C
NO
SURVEY
WIEGAND
PROG
DRY
WET
RESET TAMPER
DISABLE
SURVEY
GND
LED Survey
Button
Piezo
Wiegand
Inputs
Status
Indicator
Outputs
Zones
Reset
Tamper
LED
Indicators
Keypad
Programming
Header
Power
Supply
Door Relay
Terminal
Dry/Wet
Contact
PCB FEATURES
Figure 1: PCB Features

4 1134 Installation and Programming Guide | Digital Monitoring Products, Inc.
PROGRAM THE 1134
Refer to the panel programming guide as needed.
1. Reset the panel.
2. At the keypad, enter 6653 (PROG) to access the PROGRAMMER menu.
PART 1: DEVICE SETUP
1. In DEVICE SETUP, press CMD until you get to DEVICE NO: -.
2. Enter a DEVICE NO:- and press CMD.
3. Enter a DEVICE NAME and press CMD.
4. (XT30/XT50 only) Select YES when WIRELESS? displays.
5. (XR150/XR550 only) Select DOOR for DEVICE TYPE and press CMD.
6. (XR150/XR550 only) Select WLS at COMM TYPE and press CMD.
Note: Panel version 191 or higher software is required.
7. Enter the eight-digit SERIAL#:- and press CMD.
Note: Enter the Type 14 serial number found on the 1134 PCB or by connecting a keypad to the
header on the 1134.
8. Enter the SUPRVSN TIME and press CMD.

Digital Monitoring Products, Inc. | 1134 Installation and Programming Guide 5
PART 2: ZONE INFORMATION
1. In ZONE INFORMATION, enter the wireless ZONE NO: - and press CMD.
2. Enter the ZONE NAME and press CMD.
3. Select the ZONE TYPE and press CMD.
4. At NEXT ZN?, select NO.
5. Select YES when WIRELESS? displays.
6. Enter the eight-digit SERIAL#:- and press CMD.
Note: Enter the Type 08 serial number found on the 1134 PCB or by connecting a keypad to the
header on the 1134.
7. Enter the CONTACT number being used.
8. Enter the SUPRVSN TIME and press CMD.
9. At the NEXT ZN? prompt, select YES and continue to program up to three more zones.
Note: Zones must be entered sequentially. For example, if you program zone 71, you need to
program zone 72 as the next contact. Use the same serial number for each contact.

6 1134 Installation and Programming Guide | Digital Monitoring Products, Inc.
INSTALL THE 1134
The 1134 comes in a high-impact plastic housing that you can mount directly to a wall, backboard,
or other flat surface.
For easy installation, the back and ends of the 1134 housing have wire entrances. The back also
contains multiple mounting holes that allow you to mount the 1134 on a single-gang switch box.
DMP recommends mounting the 1134 near the protected door. Remove the PCB from the housing
base to install the housing to the wall. See Figure2 for mounting hole locations.
1MOUNT THE 1134
Mounting Hole
Figure 2: Mounting Hole Locations