DMP Electronics Wiegand 734N Installation guide

INSTALLATION AND PROGRAMMING GUIDE
734N Wiegand
Interface Modules

About the 734N/734N-POE...................... 1
Power Supply......................................................... 1
Zone Terminals ...................................................... 1
Annunciators.......................................................... 1
Indicator LEDs ....................................................... 1
Form C Relay......................................................... 2
Programming Connection................................ 2
PCB Features...............................................3
Install the 734N...........................................4
Mount the Device ................................................ 4
Wire the Electronic Lock.................................. 5
Network Connection.......................................... 5
Isolation Relay ...................................................... 8
Install the 333 Suppressor ............................... 9
Wire the Zone Terminals..................................10
Connect a Card Reader....................................13
Addressing the 734N........................................15
TABLE OF CONTENTS
Program the 734N .................................... 17
Program Start Display ......................................18
Initialization Option ...........................................18
Initialize Confirm Option .................................18
Communication Menu.......................................18
734N DHCP...........................................................19
734N IP Address.................................................19
Subnet Mask.........................................................19
Gateway Address ...............................................19
Panel IP Address.................................................19
Panel IP Port........................................................20
734N Passphrase ...............................................20
Access Options ..................................................20
Activate Zone 2 Bypass ...................................21
Zone 2 Bypass Time .........................................22
Relock on Zone 2 Change..............................22
Activate Zone 3 Request to Exit .................23
Zone 3 REX Strike Time..................................23
Activate On-board Speaker ..........................24

Custom Card Definitions .........................25
Card Options.......................................................25
Wiegand Code Length ....................................26
Site Code Position and Length ....................26
User Code Position and Length...................26
Require Site Code ............................................. 27
Site Code .............................................................. 27
Enter Site Code..................................................28
Number of User Code Digits.........................28
No Communication with Panel ....................29
Remove Keypad................................................ 30
Public Card Formats ................................ 31
734N Network Specifications.................32
Compliance Listing Specifications ....... 34
UL Access Control.............................................34
ULC Commercial Burglary (XR150/XR550
Series Panels)......................................................34
Certifications.............................................35
Underwriters Laboratory (UL Listed)........35
International Certifications.....................37
Intertek (ETL) Listed* ...................................... 37
Export Control.................................................... 37
Product Specifications ............................38
Readers and Credentials ........................ 40

Digital Monitoring Products, Inc. | 734N Installation and Programming Guide 1
ANNUNCIATORS
An on-board programmable piezo provides local
annunciation at the 734N. You can also connect
a variety of switched ground annunciators to the
734N for remote annunciation.
INDICATOR LEDS
The 734N provides three indicator LEDs. The
red LED turns on for the same duration as the
door strike relay. The yellow LED turns on for one
second to indicate receipt of a valid Wiegand
input. The green LED indicates that data is being
sent to the panel.
The 734N and 734N-POE Wiegand Interface Modules allows you to add IP network access control
capability to XR150/XR550 and XR150INT/XR550INT Series panels using proximity credential or
mag-stripe card readers. The modules also allow you to use the powerful built-in access control
capability of DMP Panels.
POWER SUPPLY
The 734N operates at 12/24 VDC from the power
supply supporting a door’s magnetic lock or
door-strike. It can also be powered from POE.
The 734N provides a 10 Amp Form C relay
contact for lock control.
ZONE TERMINALS
Four input zones are provided to allow
connection of nearby burglary devices.
ABOUT THE 734N/734N-POE

2 734N Installation and Programming Guide | Digital Monitoring Products, Inc.
FORM C RELAY
The 734N’s Form C relay draws up to 35 mA of current. See NC/C/NO (Dry Contact Relay) and
Isolation Relay for more information.
PROGRAMMING CONNECTION
The 734N also provides a keypad programming connection that allows you to use a standard DMP
LCD keypad for initial setup. Programming can be completed using a keypad connected to the 734N
or from an XR150/XR550 or XR150INT/XR550INT panel.

Digital Monitoring Products, Inc. | 734N Installation and Programming Guide 3
PCB FEATURES
DC INPUT
WIEGAND
INPUTS ZONES
PIEZO
INDICATOR
LEDS
DOOR RELAY
NETWORK
CONNECTION
Figure 1: PCB Features

4 734N Installation and Programming Guide | Digital Monitoring Products, Inc.
INSTALL THE 734N
The 734N comes in a high-impact plastic housing that you can mount directly to a wall,
backboard, or other flat surface.
DMP recommends mounting the 734N near the protected door. For easy installation, the back and
ends of the 734N housing have wire entrances. The back also contains multiple mounting holes
that allow you to mount the 734N on a single-gang switch box. See Figure2 for mounting hole
locations on the housing base.
1MOUNT THE DEVICE
Mounting Hole
Figure 2: Mounting Hole Locations

Digital Monitoring Products, Inc. | 734N Installation and Programming Guide 5
The 734N provides a Form C (SPDT) relay for controlling locks and other electronically-
controlled barriers. The three relay terminals marked NO C NC allow you to connect the device
wiring to the relay for module control.
When the 734N is powered with a 12/24 V power supply or POE, the device can power an
electric strike, up to 750 mA. See Figures 3 and 4 for typical magnetic lock and door strike
wiring. See Figure 5 for POE door strike wiring.
The Form C relay draws up to 35 mA of current and contacts are rated for 10 Amps (resistive)
at 12/24 VDC. When connecting multiple locks to the Form C relay, the total current for all locks
cannot exceed 10 Amps. If the total current for all locks exceeds 10 Amps, problems may arise
and an isolation relay may be needed. See Isolation Relay for more information.
NETWORK CONNECTION
Connect an IP network cable from the LAN/WAN connection to the 734N Network connector.
The 734N communicates AES encrypted TCP with panels that have network installed.
Two LED’s are located on the ethernet jack.
▸The green LED indicates data sent to the panel.
▸The yellow LED indicates the speed of the transmission. A solid yellow LED indicates
the network is connected at 100 Base-T. A flashing yellow LED indicates the network is
connected at 10 Base-T.
2WIRE THE ELECTRONIC LOCK

6 734N Installation and Programming Guide | Digital Monitoring Products, Inc.
PROG
J2
RED RED
KYPD IN
J4
J1
DATA
XMT LED
WIEGAND
READ LED
RELAY
ON
NCCNO
GRNYELRED
Model 333
Supressor
Normally Closed
–
+
Magnetic Door Lock
12/24 VDC
Power Supply
Figure 3: Typical
Magnetic Lock Wiring
PROG
J2
RED
J1
DATA
XMT LED
WIEGAND
READ LED
RELAY
ON
NCCNO
GRNYELRED
Model 333
Supressor
Normally Open
–+
DC Door Strike
12/24 VDC
Power Supply
Figure 4: Typical Door Strike
Wiring with Power Supply