DMP Electronics ITI 738I Installation guide

INSTALLATION AND PROGRAMMING GUIDE
738I ITI™
Interface Module

About the 738I ITI™.................................... 1
Supported Wireless Receivers
and Transmitters.................................................. 2
Install the 738I ITI™ ....................................4
Mount the Module ............................................... 4
Wire the Module .................................................. 6
Program the 738I ITI™................................8
Initialization ........................................................... 8
Panel Bus Type..................................................... 8
Zone Number........................................................ 9
Transmitter Type................................................. 12
Transmit Now .......................................................13
Already Zone ......................................................13
Already Zone ......................................................13
Exit Programming ..............................................14
738I LED Operation...........................................14
TABLE OF CONTENTS
Product Specifications ............................ 15
Certifications............................................. 16

Digital Monitoring Products, Inc. | 738I ITI™ Installation and Programming Guide 1
The 738I ITI™ Wireless Interface Module allows you to interface ITI™ SuperBus™ 2000
Series Wireless receivers with the DMP XT30/XT50 Series and XR150/XR550 Series
panels. This module allows up to 96 supervised, programmable zones of ITI wireless
transmitters when used with the ITI™ MAX SuperBus™ 2000 Radio Receiver. The 738I
allows 32 zones when used with the ITI™ 32-Zone SuperBus™ 2000 Radio Receiver and
allows 16 zones when used with the ITI™ 16-Zone SuperBus™ 2000 Radio Receiver. Tables 1
and 2 list compatible wireless receivers and transmitters.
ABOUT THE 738I ITI™

2 738I ITI™ Installation and Programming Guide | Digital Monitoring Products, Inc.
MODEL NAME
NUMBER OF SUPPORTED ZONES
XT30 XT50 XR150/XR550
16-Zone SuperBus™ 2000
Radio Receiver 16 16 16
32-Zone SuperBus™ 200032-Zone SuperBus™ 2000
Radio ReceiverRadio Receiver 16 32 32
MAX SuperBus™ 2000
Radio Receiver 16 32 96
Table 1: ITI Wireless Receivers Supported
Supported Wireless Receivers and Transmitters
The maximum wire distance between the ITI wireless receiver and the 738I is 3 feet.
Table 1 lists the wireless receivers supported and Table 2 lists the wireless transmitters
supported.

Digital Monitoring Products, Inc. | 738I ITI™ Installation and Programming Guide 3
MODEL NAME ITI MODEL NUMBER
2-Button SAW Keychain
Touchpad 60-707-0195R
4-Button SAW Keychain4-Button SAW Keychain
Touchpad*Touchpad* 60-659-95R
2-Button Crystal Keyfob 60-607-319.5
4-Button Crystal Keyfob* 60-606-319.5
SAW Door/Window Sensor 60-670-95R
Crystal Standard Door/
Window Sensor 60-362-10-319.5
Crystal Long-Life Door/
Window Sensor 60-641-95
Recessed Micro Door/
Window Sensor 60-741-95
Crystal PIR Motion Sensor 60-703-95
MODEL NAME ITI MODEL NUMBER
SAW PIR Motion Sensor 60-639-95R
Wireless AP750W PIR
Motion Sensor 60-880-95
SAW Pet Immune PIR
Motion Sensor 60-807-95R
DS 924i Pet Immune PIR
Motion Sensor 60-511-02-95
SAW Outdoor PIR Motion
Sensor 60-639-95R-OD
Water-Resistant Pendant
Panic Sensor 60-578-10-95
Wrist Watch Panic Sensor 60-906-95
Wireless ShatterPro™
Glassbreak Sensor 60-873-95
Learn Mode DS 924i PIR
Motion Sensor 60-511-01-95
Table 2: ITI Wireless Transmitters Supported
*Note: During 738I programming, the keyfob can be assigned to one zone that operates only the top two buttons
by selecting Arming zone, style Maintain. After programming is complete, the Lock button enables a
maintained Short condition that arms the assigned area(s). The Unlock button restores the zone to a Normal
condition that disarms the assigned area(s).

4 738I ITI™ Installation and Programming Guide | Digital Monitoring Products, Inc.
INSTALL THE 738I ITI™
Mount the Module
Mount on Wall
The module comes in a case that mounts directly to walls, backboards, or other flat
surfaces. Wire entrances are on the back and each side of the case. Two screw holes
at the bottom of the case are for mounting the case on single-gang switch boxes or
rings.
Mount in Enclosure
Themodule can be mounted in a DMP enclosure using the standard3-hole mounting
pattern. Refer to Figure 1as needed during installation.
1. Hold the plastic standos against the inside of the enclosure side wall.
2. Insert the included Phillips head screws from the outside of the enclosure into
the standos. Tighten the screws.
3. Carefully snap the module onto the standos.
1

Digital Monitoring Products, Inc. | 738I ITI™ Installation and Programming Guide 5
Figure 1: Stando and Module Installation
BACK
1
2
3

6 738I ITI™ Installation and Programming Guide | Digital Monitoring Products, Inc.
Wire the Module
The 738I connects to the panel 4-wire keypad data bus of XT30/XT50 Series panels
and panel 4-wire keypad data bus and the LX-Bus™ of XR150/XR550 Series panels.
Use a 4-wire harness to easily connect the 738I to an ITI Wireless Receiver.
Note: When programming 738I zones on the LX-Bus of an XR150/XR550 Series
panel, select NO when prompted whether the zone is wireless.
DMP Bus Header
For connection to a keypad bus, connect the provided Model 300 4-wire harness
(with one 4-wire connector) from the DMP BUS header to the panel terminals marked
Red (7), Yellow (8), Green (9), and Black (10).
For connection to the LX-Bus, connect the provided Model 300 4-wire harness from
the DMP BUS header to the four wires of the LX-Bus.
Receiver Header
Connect the provided Model 300 4-wire harness from the RECEIVER header to the ITI
wireless receiver.
Red = +12
Green = B
Yellow = A
Black = GND
2