DMP Electronics 7800 Series Installation guide

INSTALLATION AND PROGRAMMING GUIDE
7800 Series Graphic
Touchscreen Keypad

 
 













About the Keypad ...................................... 1
7872...................................................................................... 1
7873...................................................................................... 1
7873H................................................................................... 1
Keypad Features.........................................2
Programmable Carousel Menu ................................. 3
Enter Characters.........................................4
Number Pad ..................................................................... 4
Standard Keyboard ....................................................... 4
Install the keypad.......................................6
Remove the Cover......................................................... 6
Wire the Keypad............................................................. 7
Wire for Access Control .............................................. 9
Wire the Electronic Lock ............................................ 11
Wire the 333 Suppressor ............................................ 11
Mount the Keypad .................................... 13
TABLE OF CONTENTS
Program the Panel.................................... 15
Device Setup...................................................................15
Device Number ..................................................................15
Device Name.......................................................................15
Device Type.........................................................................16
Communication Type.......................................................16
Program the Keypad ................................ 17
Keypad Options.............................................................17
Current Keypad Address................................................17
Keypad Mode......................................................................18
Default Keypad Message................................................18
Arm Panic Keys..................................................................18
Activate Zone 2 Bypass ..................................................19
Activate Zone 3 Request to Exit..................................21
Arming/Disarming Wait Time ....................................22
Card Options .....................................................................23
Require Site Code............................................................ 27
Number of User Code Digits .......................................28
No Communication with Panel ...................................28

System Type...................................................................... 30
Dealer Logo....................................................................... 30
Dealer Info ......................................................................... 30
Carousel Z-Wave Items...................................................31
Shortcut Items....................................................................31
Select Language............................................................... 32
Additional Programming.........................33
Program a Credential .....................................................33
Update the Keypad .........................................................34
Test the keypad.........................................35
Keypad Diagnostics ....................................................35
Zone Test............................................................................. 35
Test the Credential Reader...........................................35
End User Training .................................... 36
Access the User Menu................................................36
Arm and Disarm the System....................................37
Use Access Control .....................................................38
Touchless Arming .......................................................38
Icon Reference ............................................................. 40
Change System Wi-Fi Password............................42
Clean the Keypad........................................................ 44
Keypad Bus Wiring Specifications........ 45
Public Card Formats ............................... 46
Readers and Credentials .........................47
Ordering Information.............................. 49
Keypads ...........................................................................49
Accessories.................................................................... 50
Compliance Specifications...................... 51
Certifications.............................................52
FCC Information .......................................53
Industry Canada Information................. 54

Digital Monitoring Products, Inc. | 7800 Series Installation and Programming Guide 1
ABOUT THE KEYPAD
7800 Series Graphic Touchscreen Keypads oer flexible features and functionality. Each
keypad provides optional panic keys, an AC Power/Armed LED, an internal speaker, a
simple terminal connection to a 4-wire keypad bus, and optional backboxes for conduit or
wall-mount applications. Each model provides its own distinct functionality.
7872
Provides a built-in
proximity card reader
designed to read proximity
credentials.
Provides four fully-
programmable Class B,
Style A, supervised, power
limited protection zones
that can be programmed
for a variety of burglary
and access control
applications.
7873
Provides a built-in
proximity card reader
designed to read proximity
credentials.
Provides four fully-
programmable Class B,
Style A, supervised, power
limited protection zones
that can be programmed
for a variety of burglary
and access control
applications.
Provides a door strike relay
and allows Wiegand input
from external card readers.
7873H
Provides the same
functionality as the 7873
keypad.
Allows the keypad digits to
automatically randomize
on user code entry.
Features an integrated
privacy filter on the
keypad screen.

2 7800 Series Installation and Programming Guide | Digital Monitoring Products, Inc.
KEYPAD FEATURES
Figure 1: Keypad Features


  












Armed/Power LEDs &
Proximity Reader
Dealer Logo Carousel Menu
Local
Weather
Interactive
Arming/
Disarming
Shield Press the
Navigation
Arrows or touch
and drag the
menu to scroll
microSD
Card Slot

Digital Monitoring Products, Inc. | 7800 Series Installation and Programming Guide 3
Figure 2: Keypad Options




 



Programmable Carousel Menu
The carousel menu allows the user to pick and choose what displays within the carousel
menu on the home screen. Press Options in the carousel menu. From here, adjust the
keypad screen brightness, keypad tone, and keypad volume. Press a box under Display
In Menu to select that option to display in the carousel menu. Press that box again to
deselect that option. See Figure 2.
A Brightness setting of 1 allows the keypad display to turn o automatically after a brief
period of inactivity. The Arm/Disarm LED remains lit. A Brightness setting of 0 allows both
the keypad display and LED to turn o automatically after a period of inactivity. To wake
the display, tap any part of the touchscreen surface.

4 7800 Series Installation and Programming Guide | Digital Monitoring Products, Inc.
ENTER CHARACTERS
Number Pad
1. Choose a character from Table 1.
2. Identify the Number the character
correlates with and press that
number on the number pad.
3. Identify the Select Area for the
character and press that select area
on the keypad. Press that select area
again for the lowercase letter. See
Figure 3.
4. When the desired character displays
on the keypad, return to Step 1 to
enter another character or press
CMD if finished.
Standard Keyboard
• Press ABC to enter uppercase
letters.
• Press abc to enter lowercase letters.
• Press !@# to enter special characters.
• Press 123 to enter numbers and to return to the number pad. See Figure 4.
NUMBER SELECT AREA
1 2 3 4
1 A B C ( [ {
2 D E F ) ] }
3 G H I ! ^ ~
4 J K L ? “ |
5 M N O / \ `
6 P Q R & $
7 S T U @ %
8 V W X , =
9 Y Z Space : _ ;
0 - + . ‘ * < # >
Table 1: Characters

Digital Monitoring Products, Inc. | 7800 Series Installation and Programming Guide 5
Select Areas













   
  
 

Return
to Home
Screen
1 43
Figure 3: Number Pad
2
Figure 4: Standard Keyboard
1 2 3 4
5 6 7 8
9 0 CMD
ABC DEF GHI JKL
MNO PQR STU VWX
YZ

 
         
        
      
Number Pad
Uppercase/
Lowercase
Letters
Special
Characters

6 7800 Series Installation and Programming Guide | Digital Monitoring Products, Inc.
Remove the Cover
The keypad housing is made up of two parts:
the cover, which contains the circuit board and
components, and the base.
To separate the keypad cover from the base,
insert a slotted-tip screwdriver into one of the
slots on the bottom of the keypad and lift the
screwdriver upward. Repeat with the other slot.
Separate the cover from the base and set the
cover containing the keypad components aside.
See Figure 5.
1
INSTALL THE KEYPAD
Figure 5: Separate the
Keypad Housing
Cover
Base

Digital Monitoring Products, Inc. | 7800 Series Installation and Programming Guide 7
Wire the Keypad
Each keypad model has specific wiring assignments. All zones are supervised
and suitable for residential burglary or fire applications. The maximum zone line
impedance is 100 Ohms. The ground fault is detected at 1420 Ohms or less. See
Wiring Specifications for additional wiring information.
Model 7872
Connect the supplied harness to the header on the keypad. Connect the 4-wires on
the opposite end of the harness to the panel terminals for keypad bus connection.
Connect the red wire to panel terminal 7, the white or yellow wire to panel terminal 8,
the green wire to panel terminal 9, and the black wire to panel terminal 10.
Models 7873/7873H
Connect the supplied harness to the header on the keypad. Connect the 4-wires on
the opposite end of the harness to the panel terminals for keypad bus connection.
Connect the red wire to panel terminal 7, connect the white or yellow wire to panel
terminal 8, connect green wire to panel terminal 9, and connect black wire to panel
terminal 10. Use a 5-wire harness for external card reader connection. Use 1k Ohm
EOL resistors DMP Model 311 on keypad zones 1-4. The following are optional 7873
zone input connections for access control:
• Zone 1: Brown White/White Brown
• Zone 2: Red White/White Red (Zone 2 Bypass)
• Zone 3: Orange White/White Orange (REX)
• Zone 4: Yellow White/White Yellow
2

8 7800 Series Installation and Programming Guide | Digital Monitoring Products, Inc.
1K EOL
1K EOL
1K EOL
1K EOL
White – Connect Reader Data 1
Orange – Door Strike Normally Open
Gray – Door Strike Common
Violet – Door Strike Normally Closed
Yellow/White
White/Yellow
Orange White
White/Orange
Red/White
White/Red
Brown/White
White/Brown
Black– Ground
Red – Keypad Power
– Zone 1
– Zone 2
– Zone 3
– Zone 4
Zones 1 to 4
7872 / 7873 Keypads
External Card
Reader
Green/White – Connect Reader Data 0
Black – Ground
Green – Receive Data
Yellow – Send Data
Red – Keypad Power
All Keypads
Red
Black
Green
Yellow
Surface and Backbox
Mounting Holes
Keypad Back
Figure 6: Mounting Holes and Wiring

Digital Monitoring Products, Inc. | 7800 Series Installation and Programming Guide 9
Wire for Access Control
Internal Access Control Reader
7873/7873H and 7872 keypads provide a built-in proximity card reader that is
compatible with most standard 125kHz proximity credentials. An external 13.56MHz
proximity reader can be connected and will be compatible with 13.56MHz proximity
credentials. For a list of publicly supported card formats, see Public Card Formats.
Note: Some proximity credentials are not compatible with DMP proximity
keypads. Thoroughly test the intended proximity credentials with the application
before installation. DMP does not guarantee compatibility with credentials not
purchased from DMP.
External Access Control Reader
To accept Wiegand data input from other external card readers, connect a 12VDC
external card reader to a 7873/7873H keypad. Connect the red and black power wires
from the card reader to the power wires from the panel. These connect in parallel with
the keypad power wires. Connect the Data 1 (reader) wire to the white wire on the
5-wire keypad cable. Connect the Data 0 (reader) wire to the green/white wire on the
5–wire keypad cable. See Figure 7.
3

10 7800 Series Installation and Programming Guide | Digital Monitoring Products, Inc.
Green/White* - Connect Reader Data 0
White - Connect Reader Data 1
Orange - Door Strike Normally Open
Gray - Door Strike Common
Violet - Door Strike Normally Closed
Black – Ground
Green – Receive Data
Yellow – Send Data
Red – Keypad Power
– Yellow & White
Zone 4
– Orange & White
Zone 3 (REX)
– Red & White
Zone 2
– Brown & White
Zone 1 (7/0 Panic)
NC
C
NO
WHT
GRN
Z4 -
Z4 +
Z3 -
Z3 +
Z2 -
Z2 +
Z1 -
Z1 +
BLK
GRN
YEL
RED
External Card
Reader
To Panel Keypad Bus
s
s
*Only the green/white,
white, black, and red
wires connect to the
external card reader.
1k Ω EOL
s
s
1k Ω EOL
s
s
1k Ω EOL
s
s
1k Ω EOL
Figure 7: Access Control Wiring

Digital Monitoring Products, Inc. | 7800 Series Installation and Programming Guide 11
Wire the Electronic Lock
7873/7873H keypads provide a Form C (SPDT) relay for controlling locks and other
electronically-controlled barriers. The Form C relay draws up to 15mA of current and
the contacts are rated for 1Amp at 30VDC maximum, resistive. The wires marked NO
C NC allow you to connect the device wiring to the relay for module control. Use an
additional power supply to power magnetic locks and door strikes. See Figure 8 and
Figure 9.
Wire the 333 Suppressor
Use the included 333 suppressor with the keypad to suppress any surges caused
by energizing a magnetic lock or door strike. Install the 333 across the keypad C
(common) and NO (normally open) or NC (normally closed) wires.
If the device being controlled by the relay is connected to the NO and C wires, install
the suppressor on the NO and C wires. Conversely, if the device is connected to the
NC and C wires, install the 333 Suppressor on NC and C wires. See Figure 8 and
Figure 9.
4
5

12 7800 Series Installation and Programming Guide | Digital Monitoring Products, Inc.
Model 333
Supressor
Normally Closed
– +
Magnetic Door Lock
Power Supply
Green/White – D0
White – D1
Orange – N/O
Gray – C
Violet – N/C
N/O
C
N/C
Common
Keypad
5-Wire Harness
Figure 8: Typical Magnetic Lock Wiring
Model 333
Supressor
Normally Open
– +
Door Strike Relay Power Supply
Green/White – D0
White – D1
Orange – N/O
Gray – C
Violet – N/C
N/O
C
N/C
Common
Keypad
5-Wire Harness
Figure 9: Typical Door Strike Wiring

Digital Monitoring Products, Inc. | 7800 Series Installation and Programming Guide 13
MOUNT THE KEYPAD
All DMP keypad housings are designed to install on any 4” square box, 3-gang switch box,
compatible backboxes, or directly on a flat surface. For more information about mounting
accessories, refer to “Ordering Information”.
1. Ensure all cables are routed through the keypad base cut outs before fully
mounting the base to the wall. See Figure 10.
2. Use #6 screws to secure the keypad base to the surface.
3. Place the keypad cover back onto the base and snap into place.

14 7800 Series Installation and Programming Guide | Digital Monitoring Products, Inc.
Figure 10: Mounting Hole Locations

Digital Monitoring Products, Inc. | 7800 Series Installation and Programming Guide 15
PROGRAM THE PANEL
To access the Programmer menu, reset the panel, press Keypad in the carousel menu,
enter 6653 (PROG), then press CMD.
After completing each of the following steps, press CMD to advance to the next option.
Refer to the panel programming guide as needed.
DEVICE SETUP
Advance to Device Setup, then press a select area to enter
the setup menu.
Device Number
Set the keypad address from 1-8 for XT30, XT50, and XR150
Series panels, or 1-16 for XR550 Series panels.
Device Name
Enter the a name for the device.
DEVICE SETUP
DEVICE SETUP
DEVICE NO: -
DEVICE SETUP
*UNUSED*

16 7800 Series Installation and Programming Guide | Digital Monitoring Products, Inc.
Device Type
For use as a standard keypad, select KPD. For use as an access
control keypad, press any select area, then select DOOR.
Communication Type
Ensure the COMM TYPE is set to KPD (Keypad Bus).
DEVICE SETUP
TYPE: KEYPAD
DEVICE SETUP
COMM TYPE: KPD
Configure additional options as needed. To configure custom card options for the keypad,
do not program CARD OPTIONS in Device Setup.