DMP Electronics Security Command 670-A User manual

Description The DMP 670-A and 770-A Security Command keypads provide an attractive, user friendly control with
optional2-buttonPanickeysforusewithDMPCommandProcessor™panels.Eachkeypadalsoprovides
supervised or unsupervised operation, an easy to read 16 character fluorescent blue display, AC LED,
backlit keyboard, low profile styling, and six designer colors to compliment a variety of room decors.
Security Command keypads operate on 6 to 16 VDC at 100mA with an unlit display. Current increases to
125mA with the display lit. Keypads can be installed on individual wiring runs of up to 500' using 22 gauge
wire or up to 1,000' using 18 gauge wire.
2-Button Panic Keys
ThePanickeyfunctionofthe670-Aand770-AkeypadsletsuserseasilysendaPanic,Emergency,orFire
report to the central station from DMP panels. The user must press and hold the appropriate two Select
keys for two seconds until a beep from the keypad is heard. At
thebeep,thepanelsendsanalarmreporttothecentralstation
with the following loop numbers: 19 - Panic, 29 - non-medical
Emergency, and 39 - Fire. Version 111 or higher firmware is
required in 1912XR panels for this feature.
ThePanickeyfunctionisactiveassoonasyouapplypowertothekeypad.Noadditionalloopprogramming
is necessary. If the system owner intends to use the Panic keys, install the supplied icon label below the
top row of Select keys. See Figure 1.
To disable the 2-Button Panic keys and 7/0 Panic feature (see 7/0 Panic below), cut the jumper labeled
"CUT JUMPER TO DISABLE 7/0 PANIC BUTTONS J3" on the right side of the keypad circuit board.
Unsupervised Operation
Bothkeypadsalsoallowyouto select unsupervisedaddressesandconnectmultiplekeypads to anyofthe
panel'savailablekeypad addresses.Thisfeature isrecommended for the670-A onlyandgreatly expands
thenumberofkeypadsthatcanbeinstalledtogiveusersthemaximumflexibilityinoperatingtheirsystem.
The unsupervised operation works on all DMP 1512 and 1912 Command Processor panels and 1912XR
panels with firmware version 111.
Address Programming
Usetheslide switchesnumbered1, 2,and3 ontheleft side ofthe
circuitboardtosetthekeypadtooneofthepanel'seightavailable
addresses.SeeFigure2.Placeslideswitchnumber4inthedown
position for supervised operation and in the up position for
unsupervised operation. Multiple unsupervised keypads can be
assigned to the same address.
7/0 Panic The 670-A and 770-A Security Command keypads also provide users with an additional panic feature by
programming the first loop on the assigned address as a Panic loop. A user pressing the 7and 0keys
simultaneously shorts the loop and allows the panel to send a Panic report to the central station. The loop
returns to normal when they release the keys. When using the 770-A keypad, place a 1K ý resistor on
loop 1 to provide a normal loop condition.
LT-0242 (5/96)
Figure 1: Panic key label placement
5
1
8
7
6
4
32
1 2 3 4
ON
1 2 3 4
ON
1 2 3 4
ON
1 2 3 4
ON
1 2 3 4
ON
1 2 3 4
ON
1 2 3 4
ON
1 2 3 4
ON
Figure 2: Supervised keypad addresses
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
INSTALLATION 670-A and 770-A Security Command®Keypads
}Labelshows
iconsonly
Top row SELECT keys
Police Emergency Fire

Harness Color Code
Wiring to Panel 770-A Loops Wiring
Red - Auxiliary Power White/Brown - Loop 1
Yellow - Data Transmit White/Red - Loop 2
Green - Data Receive White/Orange - Loop 3
Black - Ground White/Yellow - Loop 4
Self-Test Diagnostics
The 670-A and 770-A keypads allow you to test all system keypad functions. To test the keypads:
• Disconnect the red (+12 VDC), yellow, and green keypad wires from the panel.
• Twist the yellow and green keypad wires together. Reconnect the red wire to the panel.
The keypad display shows: TEST PROCEDURE.
TEST 1 DISPLAY TEST
This test begins immediately and scrolls a series of characters across the display allowing you to visually
inspect each display segment.
To go to the next test, press the COMMAND key. To repeat a test, press the ARROW key.
TEST 2 KEY TEST
Thisallows you to checkeach key for properoperation. The display shows:PRESS KEY— . As you press
and hold each key, its name is displayed.
TEST 3 LOOP TEST (Not available on the 670-A keypad)
This allows you to check each keypad loop for proper operation. The display shows: L1 L2 L3 L4.
Following each loop number is the status of the loop. (O) = Open, (–) = OKAY, and (S) = Short.
TEST 4 FUNCTION TEST
This allows you to check the AC LED and keypad tone for proper operation. The display reads: LED RLY
TONE.Totesteachfunction,presstheselectkeybeneathitsname.Thekeyboardbacklightturnsoffduring
this test. The RLY (relay) function is not available on 670-A and 770-A keypads.
TEST 5 ADDRESS TEST
This test displays the address selection of the keypad. The display ADDRESS 2 U indicates the keypad
being tested is set to address 2 and is also unsupervised. Supervised keypads show only the address
number. A "?" (question mark) is displayed if an address selection above 8 has been made. To end the
Address Test, press COMMAND. The display reads: * * TEST END * *.
Reconnecting the keypad wiring
Disconnect the red wire from the panel. Separate the yellow and green keypad wires and reconnect them
to the panel. Connect the red wire to the panel. Press COMMAND to start the keypad's normal operation.
Additional Diagnostics
Ifatanytimeduringnormaloperationasupervisedkeypadcannotdetectpollingfromthepanelonthegreen
keypad wire, the display reads: SERVICE REQUIRED. This indicates the green wire may be broken.
If at any time during normal operation a supervised keypad detects polling but its particular address is not
being polled, the display reads: NON-POLLED ADDR. To clear this display, check the address selection
on the keypad or the number of keypad addresses you've assigned during system programming.
Additional Power Supply
Ifcurrentdrawforallkeypadsconnectedtothepanelexceedsthepanel'soutput,youcanprovideadditional
current by adding an auxiliary power supply. Connect all keypad Ground (common) wires to the negative
terminal of the power supply. Run a jumper wire from the power supply's negative terminal to terminal 10
of the panel. Connect all keypad power (+12 VDC) wires to the positive terminal of the power supply. Do
NOT connect the positive terminal of the power supply to any terminal of the panel.
AC LED
TheModel670-Aand 770-Akeypadseachdisplay agreenACpower LED.TheLEDis offwhenACpower
to the panel has been interrupted or while the panel is resetting.
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Digital Monitoring Products