DMP Electronics Thinline 7160 User manual

7000 Series Thinline™ and Aqualite™ Keypad
Quick Start Guide
Full Installation and Programming Guide
To view the full 7000 Series Thinline™ and Aqualite™ Keypad Installation and Programming Guide,
scan this QR code or visit DMP.com.
This quick start guide walks you through installing the keypad.
Step 1: Remove the Cover
Insert a slotted-tip screwdriver into one of the slots on the bottom of the keypad and lift the screwdriver upward. Repeat
with the other slot. Separate the cover from the base and set the cover containing the keypad components aside.
Step 2: Wire the Keypad
Use 1k Ohm EOL resistor on keypad zones 1-4.
1. Connect the harness to the keypad header.
2. Connect the red wire to panel terminal 7.
3. Connect the yellow wire to panel terminal 8.
4. Connect the green wire to panel terminal 9.
5. Connect the black wire to panel terminal 10.
Models 7060/A, 7063/A, 7160, and 7163
Supplied with a 4-wire harness for panel keypad bus
connection.
Models 7070/A, 7073/A, 7170, and 7173
Supplied with a 12-wire data bus/zone harness. Four
wires connect to the keypad bus. The remaining
eight wires are for the four zone inputs, four wires
for each zone.
Models 7073/A and 7173
Supplied with a 5-wire output/reader harness and a
12-wire data bus/zone harness.
ExternalReader/Door Strike
7073/7073A, 7173 Keypads
All Keypads
Zones 1-4
7070/7070A
7073/7073A
7170/7173 Keypads
All zones are supervised and suitable for fire applications.
Maximum zone line impendence is 100 Ohms.
Ground fault detected at 1420 Ohms or less.
Surface and Backbox
Mounting Holes
Combined 4-square
and 3-gang switch box
Mounting Holes
Surface and Backbox
Mounting Holes
Violet - Door Strike, Normally Closed
Gray - Door Strike, Common
Orange - Door Strike, Normally Open
White/Green - Reader Data 0
White - Reader Data 1
Black - Ground
Green - Receive Data
Yellow - Send Data
Red - Power
White/Yellow - Zone 4
1k Ω
White/Orange - Zone 3 1k Ω
White/Red - Zone 2
1k Ω
White/Brown - Zone 1 1k Ω
FRI 2:52 PM
A
C
B
D
F
E
G
I
H
J
L
K
V
X
W
S
U
T
P
R
Q
M
O
N
Y
Z
E
N
T
E
R
B
A
C
K
ALL RESET HOME
CHIME PERIM SLEEP
1 2 3 4
5 6 7 8
9 0
CMD
A
POWE
R
R
M
E
D
Panic Keys
Power LED
Armed LED
Proximity
Credential
Reader and
Backlit Logo
32-Character
Display
Select Keys
Command Key
Back Arrow Key

18205
LT-2584 22143
INTRUSION • FIRE• ACCESS• NETWORKS
2500 North Partnership Boulevard
Springfield, Missouri 65803-8877
Domestic: 800.641.4282 | International: 417.831.9362
DMP.com
© 2022
Step 3: Wire for Access Control (Optional)
For all wiring instructions, scan the QR code at the beginning of the document.
Step 4: Wire the Electronic Lock
The Form C relay on 7073/A and 7173 keypads draws up to 15 mA of current and the contacts are rated for 1 Amp at
30 VDC maximum, resistive. The wires marked NO C NC allow you to connect the device wiring to the relay for module
control. Use an additional power supply to power magnetic locks and door strikes.
Green/White – D0
White – D1
Orange – N/O
Gray – C
Violet – N/C
NC
C
NO
WHT
GRN
None
To Keypad
Magnetic Door Lock
Normally Closed
Normally Closed Normally Open
Common
Power Supply
Model 333
Supressor
NC
C
NO
WHT
GRN
None
To Keypad
Door Strike Relay
Normally Opem
Common
Power Supply
Model 333
Supressor
Step 5: Wire the 333 Suppressor
Use the included 333 suppressor with the keypad to suppress any surges caused by energizing a magnetic lock or door
strike. Install the 333 across the keypad C (common) and NO (normally open) or NC (normally closed).
If the device is being controlled by the relay is connected to the NO and C wires, install the suppressor on the NO and C
wires. Conversely, if the device is connected to the NC and C wires, install the 333 Suppressor on NC and C wires.
Step 7: Program the Panel and Keypad
For all programming instructions, scan the QR code at the beginning of the document.
Step 8: Test the Keypad
For all testing instructions, scan the QR code at the beginning of the document.
Step 6: Mounting the Keypad
All DMP keypad housings are designed to install on any 4” square box,
3-gang switch box, compatible backboxes, or directly on a flat surface.
1. Ensure all cables are routed through the keypad base cut outs
before fully mounting the base to the wall.
2. Use #6 screws to secure the keypad base to the surface.
3. Place the keypad cover back onto the base and snap into place.
A
A
A
A
B
B
D
B
B
C
C
DD
D
A
B
Backbox
mounting holes
Switchbox
mounting holes
CWiring cutouts
DCover latches