Dnake 280M-S8 User manual

Model: 280SD-C12
280SD-R2
280SD-R5
Quick Start Quide
Door Station
The picture is only a schematic diagram. The actual product shall prevail.
USER MANUAL

Please follow the user manual for correct installation and
testing. If there is any doubt please call our tech-supporting
and customer center.
Our company applies ourselves to reformation and
innovation of our products. No extra notice for any change.
The illustration shown here is only for reference. If there is
any difference, please take the actual product as the
standard.
The product and batteries must be handled separately from
household waste. When the product reaches the end of
service life and needs to be discarded, please contact the
local administrative department and put it in the designated
collection points in order to avoid the damage to the
environment and human health caused by any disposal. We
encourage recycling and reusing the material resources.
REMARK

CATALOG
Product Features .....................................................1
Technical Parameters .............................................1
Package Contents...................................................2
Pictures.....................................................................2
Operations ...............................................................3
1. Security .................................................................4
2. Smart ....................................................................9
3. Intercom .............................................................12
4. Message ..............................................................14
5. Setup ...................................................................15
Web Settings..........................................................18
System Configuration..........................................20
System Diagram ....................................................21
Installation .............................................................23
Troubleshooting....................................................24
Safety Instructions................................................25

PRODUCT FEATURES
1. Building intercom application:
Talkback: Support video call, monitoring, unlocking and checking of
call records.
Security: Support 8 alarm zones with three states, zone and scene
setup.
Smart: Support smart home extension by RS485 communication.
2. Operating system: Linux.
TECHNICAL PARAMETERS
Voltage: DC 12V
POE
Rated power: 9W
Standby power consumption: 1.5W
Display screen: 7''
Touch screen: Capacitive touch screen
Resolution: 800x480
Working Temperature: -10℃ to +55℃
Storage Temperature: -10℃ to +60℃
Working Humidity: 10% to 90% (non-condensing)
1

Package Contents
Quick Start Guide
Indoor Monitor
MODEL: 280M-S8
Please make sure the package contains the following items:
Screw
PACKAGE CONTENTS
2
PICTURES
Microphone
7'' capacitive
touch screen
Speaker

3
OPERATIONS
Main menu: Security, Smart, Intercom, Message and Setup.
Status bar: Network connection and security precautions.
Shortcut key: Do Not Disturb, Message, Records.
Instructions of status bar and shortcut key:
1. DND :Click icon, the system will enter DND or undo DND. You can
use Do Not Disturb service when you don't want to be disturbed by
calls(The valid time is 8 hours).
2. Message : Click it to enter the Message interface.
3. Network connection : When the icon keeps lit, the indoor monitor is
connected to the network.
4. Security precautions : The icon flashes during activation time and
keeps lit after arming successfully.
5. SIP Registration Status : This icon keeps lit when SIP account is
registered.

Clicking “Security” icon on the main interface, the system will enter the
following interface:
1.Security
1.1 ON/OFF
Clicking “ON/OFF” icon, the system will enter the following interface:
1.1.1 ON
Click “Out” “Home”, or “Sleep” icon to activate the alarm sensors. The
corresponding icon on the main interface will be lit up with a beep and it
will stay lit.
1.1.2 OFF
(1) During the delay time of arming, clicking “OFF” icon, the system will emit
a beep. Then the alrm will be stopped.
(2) Input user password(the default password is 1234) to stop the alarm
under ON status.
4

1.2.1 IP Camera Setting
Login the webpage of indoor monitor by username: user, password:1234,
and then you can access the following webpage:
1.2 Camera
Clicking “Camera” icon, the system will enter into the following interface:
Click icon or icon button to select the camera you want, and then
click to monitor the IP camera. If you want to cancel monitoring, click
to stop it.
5

Clicking “Camera” icon, the system will enter into the following interface:
Click icon or icon button to select IP Camera to monitor, and then
click icon to monitor. Click to stop monitoring.
Fill in with the RTSP format: rtsp:// user: password@ Camera IP. IP is the IP
address of your IP Camera. Then you can monitor IP Camera in Security
menu on your indoor monitor:
1.3 Zone
Remark: It should be set when the alarm is OFF.
Click “Zone” icon and input 1-16 digits password(the default password is 1234),
the system will enter into the following interface:
6

NO.Type Mode Delay Sensor
1
2
3
4
5
6
7
8
24 Hour 3C
3C
3C
3C
3C
3C
3C
3C
0s
0s
0s
0s
0s
0s
0s
0s
Smoke
OK
24 Hour
24 Hour
24 Hour
24 Hour
24 Hour
24 Hour
24 Hour
Smoke
Smoke
Smoke
Smoke
Smoke
Smoke
Smoke
1.3.2 Mode
Clicking mode setting box, it will pop up a dialog box as the following
interface. On this interface, you can set mode as: 3C, NO, NC or BELL.
1.3.1 Alarm Type
Clicking input box of type, a dialog box will pop up as below. On this
interface, you can set alarm type as: Normal, Emergency or 24H. 24H and
Emergency type are always active.
NO.Type Mode Delay Sensor
1
2
3
4
5
6
7
8
24 Hour 3C
3C
3C
3C
3C
3C
3C
3C
0s
0s
0s
0s
0s
0s
0s
0s
Smoke
OK
24 Hour
24 Hour
24 Hour
24 Hour
24 Hour
24 Hour
24 Hour
Smoke
Smoke
Smoke
Smoke
Smoke
Smoke
Smoke
Normal
Emerg.
24 Hour
NO.Type Mode Delay Sensor
1
2
3
4
5
6
7
8
24 Hour 3C
3C
3C
3C
3C
3C
3C
3C
0s
0s
0s
0s
0s
0s
0s
0s
Smoke
OK
24 Hour
24 Hour
24 Hour
24 Hour
24 Hour
24 Hour
24 Hour
Smoke
Smoke
Smoke
Smoke
Smoke
Smoke
Smoke
3C
NO
NC
BELL
7

When alarm sensor is triggered, the indoor monitor will make a loud alarm
sound, and the system will enter into the following interface as well as send
alarm message to master station(if master station is installed in your
system):
You can see the No. and sensor type in red color shown at the top of
interface. Fox example, “1: Smoke” indicates that smoke sensor in zone 1 is
triggered.
To stop the alarm sound, input the password (the default password is 1234).
OK
1.4 Scene
Clicking “Scene” icon, the system will enter into the following interface:
OK
8

refers to Alarm ON, and refers to Alarm OFF. To set the sensor of
alarm stations, you can click the corresponding station with icon. Click
"Activation time" to choose the corresponding time. The options of
activation time include NONE, 30s, 40s, 60s, 100s and 300s.
You can set the new user password with 1-16 digits (the default password is
1234). User password is used for security.
1.5 Setup
Clicking “Setup” icon, the system will enter into the following
OK
Clicking “Smart” icon on the main interface, the system will enter into the
following interface:
2.Smart
9

Scene mode includes: Home, Out , Dinner, Party and Sleep.
2.1 Scene
Clicking “Scene” icon, the system will enter into the following interface:
2.2 Light
Clicking “Light” icon, the system will enter into the following interface:
Set the light of corresponding room, such as Master, Sub, Living and Dining
Rooms (see the room setting for details). Up to 8 lights can be set in every
room. Clicking the corresponding light icon, you can turn the light ON/OFF.
10

2.4 Curtain
Clicking “Curtain” icon, the system will enter into the following interface:
By clicking “Close” icon, the curtain will be closed; by clicking “Open” icon,
the curtain will be open; by clicking “Pause” icon, the curtain will be paused.
2.5 Elevator
Clicking “Elevator” icon, the system will enter into the following interface:
Click or icon to control the up and down of the elevator. Click “Permit”
icon to permit access to the floor where the indoor monitor locates.
Remark: To support this interface, your system must be connected with
“Elevator Control” module. Kindly check with your system provider.
Permit
11

Clicking “Intercom” icon on the main interface, the system will enter into
the following interface:
3.Intercom
3.1 Call Out
Clicking “Call Out” icon, the system will enter the following interface:
3.1.1 Call unit resident
Input 1-3 digit building No.+ “Building” + 2-digit Unit No. + “Unit” +4-digit
room No., then click icon to call.
The system will enter into the following interface:
12

When answering the call, the system will enter into call status:
Click icon to communicate with door station A; click icon to end the
call; click icon to unlock the door.
3.1.2 Call management center
Clicking “Center” icon to call management center (namely master
station), the system will call management center 1 to 5 sequentially. If the
management center cannot be searched or the call failed, the system will
call next management center. When the management center answers, the
indoor monitor will ring and stop calling.
Click icon to end the communication.
3.2 Monitor
Clicking “Monitor” icon, the system will enter the following interface:
Door1
13

Click “Door1” icon to switch the type of door station, then click or icon
to select the area you want to monitor, and click icon to monitor the
door station or secondary door station. Click icon to stop monitoring.
Click icon to unlock the door.
Remark: The system’s default monitoring time is 25s.
3.3 Records
Clicking “Records” icon, the system will enter the following interface:
refers to call-out record; refers to call-in record; refers to missed
call record. It can save up to 64 records.
Click or icon to search for records. Select one record and click icon
to call; click icon to delete it.
If the snapshot is taken, click icon to view it.
4. Message
Clicking “Message” icon, the system will enter into the following interface:
1 Announcements 16-10-10 14:44
2 Today's Top Headlines 16-10-13 18:14
3 News Service 16-10-17 15:54
4 Visual Reporting 16-10-19 11:44
14

Note: only by installing the management software on PC which is usually
located at guard center, can indoor monitor receive the message sent by
PC.
Click icon to page up; click icon to page down; click icon to delete
the record.
5. Setup
Clicking “Setup” icon, the system will enter into the following interface:
5.1 Normal
You can select the volume, intercom, language, time zone and auto answer.
OK
o
5.2 Room
Click “Room” icon, then input 1-16 digits password (the default password
is 123456 ) to enter into the following interface:
15

5.3 Network
Click “Network” icon, then input 1-16 digits password (the default password
is 123456 ) to enter into the following interface:
IP: the system will automatically display IP address of the indoor monitor.
IP address is unique.
The default Mask address is 255.255.255.0. Normally, it is unnecessary to modify.
If you would like to modify it, a keypad will pop up when clicking the setting
box twice. Enter your new Mask address.
The Gateway in one system must be on the same segment.
DNS: domain name resolution address (DNS of local operator). If indoor monitor
is used on WAN, the address must be entered correctly; if it is used on LAN, the
address can be ignored.
Server: the system will automatically display IP address of the current indoor
monitor.
OK
o
5.4 Password
Click “Password” icon to enter into the following interface:
OK
o
16

You can set the new system password with 1-16 digits (the default
password is 123456). System password is used for system settings.
5.5 Version
Click “Version” icon to enter into the following interface:
You can look over the relevant information.
o
17