DOD LS300W Manual

硬體安裝指南
安裝與固定 軟體操作指南
SD
1.請先將記憶卡依指定方向插入主機，並使用支架將主機固定於車內。
2.使用支架時，請慎選擺放位置。切勿將主機放在會阻礙開車視線或
影響安全氣 囊正常 運作的位置。
3.如果汽車檔風玻璃內外有油漬、指紋或其它髒汙，請先擦拭乾淨後
再安裝。
開機流程
1.插入記憶卡
2.將車用電源分別插入汽車點煙頭與主機
3.發動汽車
4.主機開機 ，系統 將會自動開始錄影
請插入車用電源並發動汽車，主機會立即開機。
當汽車熄火或者移除車用電源，主機自動關機。
注意事項
1.當車輛熄火後點煙器仍供電的使用者，請在離開車子時務必將點
煙器插頭拔起。
2.請使用8GB Class 6以上規格的Mic ro SD卡 。
開機畫面
錄影畫面
系統設置
錄影設定 回放模式
播放流程
1.停止錄影後按二下MODE鍵進入影片播放模式。
2.按上下鍵 選擇到 想要播放的影片。
3.按下確認 鍵開始 播放影片。
4.再一次按 下確認 鍵暫停播放影片。
影片刪除
1.停止錄影後按二下MODE鍵進入影片播放模式。
2.按上下鍵 選擇到 想要刪除的影片。
3.按下MENU鍵進入 選單進 行影片刪除或全部 刪除。
電腦播放
建議使用免費的VLC PLAYER播放記憶卡中的影像
請連線到http://www.videolan.org/vlc/ 下載VLC PLAYER並安裝即可
播放1080P 30fps影像電腦規格建議：
1.intel Core 2 Duo 2.0GHz 以上CPU
2.2G以上DDRII記憶體
3.支援DirectX 10以上規格之顯示卡
8
910 11 12
16
3.方向上/放大
5.選單/SOS緊急檔案鎖
4.方向下/縮小
7.2.7寸TFT顯示螢幕
6.模式切換按鍵
8.Mirco-SD卡插槽
9.錄影/拍照/確認
10.電源開關
11.AV輸出接口
15.HDMI輸出接 口
14.喇叭
13.LED燈
16.重置鍵
2.麥克風
1.指示燈
15
13
14
MENU
3 5
1
46
7
12.USB/車充電 源插孔
2
停止錄影後按一下MENU鍵進入錄影設定
解析度：設定錄影解析度大小。
循環錄影：設定錄影循環時間或關閉循環錄影功能。
WDR 開啟或關閉WDR功能。
曝光值調整：設定曝光值大小。
位移偵測：開啟或關閉 位移偵 測錄影功能。
錄音：開啟或關閉錄音功能。
日期記錄：開啟或關閉 日期記 錄功能。
重力感應：設定G-Senso r觸發檔案保護的靈敏度。
：
停止錄影後按二下MENU鍵進入系統 設定
日期/時間 更改系統時間。
自動關機：設定主機斷電後 自動關機 的時間或不關機直至電力耗盡。
螢幕關閉：設定螢幕自動關 閉時間， 或永遠開啟
提示音：開啟或關閉系統 提示音。
語言：支援多國語言， 可依您的 喜好調整。
電視輸出：影像輸出時，可調整NTSC與PAL。
頻率：支援50Hz與60Hz。
格式化：將記憶卡進行格 式化，格 示化前請先備份資料。
預設值：將所有設定回復 至原廠預 設狀態。
版本：查看系統版本號 。
：
開啟與關閉主機電源
產品結構（包含 熱鍵）
LS300W
MENU
MENU
MENU

Hardware Installation Guide
Installation and Fixation Software Operation
SD
1.Please insert the memory card into the SD Card Slot with the
specified direction, and then use the bracket to install the device
inside the car.
2.When using the bracket, please choose the position carefully. Do
not place the device in the position that blocks the driver's sight
or affects thel work of the airbags.
3.If there is any splotch, fingerprints or other kinds of smudginess
on the windshield, please wipe clean it before installing.
1.Insert the memory card
2.Connect the car charger into the vehicle
cigarette lighter and the device
3.Start the vehicle.
4.The device be turned on, and start
recording automatically.
Please connect the vehicle cigarette lighter and start the engine, the
device will be switched on immediately.
When the engine stoppedor the vehicle power supply be removed,
the device will shutdown automatically.
Notes
1.For the users whose vehicle cigarette lighter keeps power
supplying after the engine stopped, please unplug the car
charger before leaving the vehicle.
2.Please use Class 6 or above Micro SD card
DOD Opening
System Settings
Recording Settings Video Playback
Video-Play Operation
1.After stopped recording, press MODE to enter the video-play
mode.
2.Press UP or Down to select the desired video to play.
3.Press CONFIRM to start playing video.
4. Press CONFIRM again to pause the video.
Delete Video
1.After stopped recording, press MODE to enter the video-play
mode.
2.Press UP or Down to select the desired video to delete.
3.Press MENU, enter the menu to delete the video or delete all.
Play on Computer
It is recommended to play the video by free software VLC PLAYER.
Please go to http://www.videolan.org/vlc/ to download and install
VLC Player.
Recommended PC requirements for 1080P 30fps video playing:
1.intel Core 2 Duo 2.0GHz or above CPU
2.2G or above DDRII RAM
3.Graphic card supports DirectX 10 or above
8
910 11 12
16
3.UP/Zoom in
5.MENU/SOS Emergency File Lock
4.DOWN/Zoom out
7.2.7-Inch TFT Display Screen
6.MODE Switch
8.Micro-SD Card Slot
9.Video Recording/Camera/Confirm
10.Power switch
11.AV Output Port
15.HDMI Output Jack
14.Speaker
13.LED lamp
16.Reset key
2.Microphone
1.Indicator
15
13
14
MENU
3 5
1
46
7
12.USB/Vehicle Charger Power
SupplyJack
2
After stopped recording, press MENU to enter the recording
settings.
Resolution: Set the recording resolution.
Record Cycle: Set the video length in recording cycle mode, or
toggle off record cycle function.
WDR: Toggle on or off the WDR function.
EV: Set the exposure value.
Motion Detection: Toggle on or off the motion detection recording
function.
Sound Recording: Toggle on or off the sound recording function.
Date Stamp: Toggle on or off the data stamp function.
G-sensor: Set the sensitivity level of the G-sensor file protection .
After stopped recording, press MENU twice to enter the system
setup.
Date/Time: Set the system time.
Auto Power Off: Set the automatic shutdown time after the
power disconnected or keep the device working until the
battery run out.
LCD Off: Set the screen automatic off time, or set it as always on.
Beep: Switch on or off the system beep indicator.
Language: Support multiple languages; you can choose the
language according to your preferences.
TV Mode: You can toggle between NTSC and PAL when in video
output mode.
Frequency: Support 50Hz and 60Hz.
Format: Format the memory card; please backup your data
before formatting.
Default Setting: Reset all the settings to the default state.
Version: Check the system version number.
Power On/Off
Product Structure (Including Hotkey)Switch On
Recording image
LS300W
MENU
MENU
MENU