Dogtra 1900S Series User manual

1
RemoteControlledDogTrainingCollars
Owner’sManual
www.dogtra.com
Series

1
By Dogtra
Remote Controlled Dog Training Collars
Owner's Manual
Please read this manual thoroughly
before operating the Dogtra 1900S training collar.

2
Product Safety and Health Statement
Proper e-collar use
Dogtra e-collars are intended for the sole purpose of
behaYior modi¿cation of dogs. They are 12T intended for
human use or use on other animals. Dogtra Company does
not assume any liability for the improper use of a Dogtra
e-collar.
Aggressive dogs
Dogtra highly recommends consulting a dog training
professional when using an e-collar to correct dogs that are
aggressive towards other dogs or people.
Interference with other electronic devices
Dogtra¶s industry-leading technology ¿ltering system
ensures minimal interference with other electronic devices
garage door openersmobile phonesetc.. 2ur digital
microprocessor offers thousands of unique codes to
eliminate frequency match-up with other Dogtra e-collars.
Dogtra recommends consulting your physician if you are
going to use the e-collar and you have any type of medical
devices.
Inadvertent activation
If the constant button is held down for 12 seconds or more,
the unit will automatically shut down. It reactivates when
the button is released and depressed again.
Proper Fit
$loose ¿t can allow the receivercollar to move around on
the dog’s neck. When this happens, the contact points may
rub the skin and cause irritation. If the unit is too loose, the
contact points will not make proper contact and your dog
will not receive consistent stimulation.

3
Duration your dog can wear the unit
/eaving the receivercollar in the same location on the
dog’s neck for an extended period of time can cause skin
irritation. If the dog is to wear the e-collar for long periods,
occasionally reposition the receivercollar so that the contact
points are moved to a different location on the dog’s neck.
Make sure you check for skin irritation each time you use
the unit. If your dog exhibits signs of skin irritation, consult
with a veterinarian.
Reaction to the stimulation
Every dog has a different tolerance and reaction to the
stimulation. Please look at your dog’s reaction to ¿nd Must
the right level of stimulation. The stimulation level may
vary depending on the situation and distractions. 1ormally
a distracted dog (chasing another dog, squirrel, etc.) will
require a higher level of stimulation compared to when
there is no distraction.
Training Methods
E-collars can be used with many different methods. If you
have any concerns in the training methods provided by
Dogtra, consult with a dog training professional.

4
Table of Contents
At a Glance ........................................................
Main Features of the 1900S ....................................
2verview ...........................................................
Understanding your training system
1. +ow to turn the 1900S onoff .............................
2. How the transmitter buttons work .......................
3. Collar ¿tting .................................................
4. How to ¿nd the right stimulation .........................
5. To maximize the distance .................................
6. The LED indicator ..........................................
7. Charging the battery ........................................
8. The handheld transmitter LCD ...........................
9. How to attach the belt clip on the 1900S ..............
10. How to use the test light ..................................
General Training Tips ............................................
Maintenance ......................................................
Troubleshooting Guide ..........................................
Warranty and repair information ..............................
5
6
7
10
11
14
15
15
16
17
18
20
21
22
24
25
27

5
At a Glance
Optional accessories
Field auto charger
Dogtra’s ¿eld auto chargers are designed for use with a
10-volt car outlet.
European charger
Dogtra’s European chargers are designed for use with a
230V AC electrical outlet.
To purchase accessories, please visit www.dogtra.com or
call customer service at 1-888-811-9111.
2wners
Manual
Belt clip Test light Gear bag
Receiver
Collar
Transmitter Battery
charger
Splitter
cable

6
Main Features of the 1900S
Rheostatvolume style with stimulation levels 0a127
34 - mile range
3/4
2-hour rapid charge batteries
Fully waterproof
LCD screen
Belt clip
Slim design receivercollar ergonomically
shaped to your dogs neck
Checkered grips on the handheld transmitter
LowHigh Stimulation
1on-Stimulating High Performance Pager
µ1ick’ and µConstant’ stimulation
Enhanced Contact Points

7
Overview
Transmitter
Antenna
Rheostat
intensity dial
2noff
switch
Belt clip
Battery
charging
receptacle &
rubber plug
LCD
screen
Pager
button
1ick
button
Indicator
light
(LED
window)
Constant
button

8
Overview
Transmitter
Antenna
Rheostat
intensity dial
2noff
switch
Belt clip
Battery
charging
receptacle &
rubber plug
2nd-dog
Pager
(orange
button)
LCD
screen
1st-dog
Pager
(gray
button)
1st-dog
1ick &
Constant
(gray
button)
Indicator
light
(LED
window) 1ick
Constant
toggle
switch
2nd-dog
1ick &
Constant
(orange
button)

9
Receiver/Collar
Contact points
Collar strap
Battery charging
receptacle &
rubber plug
Indicator light
(LED window)
2noff
switch

10
Understanding your training system
1. How to turn the 1900S on/o
To turn the handheld transmitter on, hold down the button
on the right side of the transmitter until the LCD screen
illuminates. To turn the transmitter off, hold down the same
button on the right side of the transmitter until the LCD screen
shuts off.
To turn the receivercollar on, hold down the onoff button until
the LED indicator turns green. To turn the receivercollar off,
hold down the onoff button until the LED indicator turns red.
2noff
Button
2noff Button

11
2. How the transmitter buttons work
1900S
The transmitter for the 1900S single dog unit has four
buttons (one on the face of the transmitter, two on the left
side and one on the right side).
Nick Button
The ³1ick´button is located on top on the left side of the
handheld transmitter. When the ³1ick´button is pressed the
receiver emits a single pulse of electrical stimulation.
Constant Button
The ³Constant´button is located on the bottom on the left
side of the handheld transmitter. Pressing the ³Constant´
button gives continuous stimulation as long as the button is
pushed, for up to 12 seconds. If the button is not released
after 12 seconds, the stimulation will automatically turn off
as a safety feature. The collar will be ready to be reactivated
once the button has been released.
Pager Button
The ³Pager´button is located on the face of the transmitter.
Pressing it will give non-stimulating vibration as long as the
button is depressed, for up to 12 seconds.
2noff switch
Pager
button
1ick
button
Constant
button

12
Transmitter Power ON/OFF
The button on the right side of the transmitter is the ³21
2FF´button that activates the transmitter and LCD screen
only. To turn the transmitter on, press the ³212FF´button
on the right side of the transmitter until the LCD screen
illuminates. To turn the transmitter off, press the ³212FF´
button on the right side of the transmitter. When the LCD
screen displays ³2FF´release the button.
1902S
The 1902S two-dog unit has ¿ve buttons and a toggle
switch on the transmitter (two on the face of the transmitter,
two on the left side, and one on the right side.).
Nick & Constant Toggle Switch
Located on the face of the transmitter is a toggle switch.
The toggle switch has a setting for ³1ick´and another for
³Constant´. The color-coordinated buttons (orange for the
orange receivercollar and gray for the black receivercollar)
will implement the desired stimulation based on the toggle
switch setting.
2noff switch
1ickConstant
toggle switch
2nd-dog
Pager
(orange button)
1st-dog
Pager
(gray button)
1st-dog
1ick & Constant
(gray button)
2nd-dog
1ick & Constant
(orange button)

13
When either the orange or gray stimulation button is pressed
and the toggle is set on ³1ick´the receiver emits a single
pulse of electrical stimulation.
When you press either the orange or gray stimulation
button, and the toggle is set on ³Constant´, the receiver
emits a continuous stimulation as long as the button is
pushed, for up to 12 seconds to the corresponding collar.
If the button is not released after 12 seconds, the stimulation
will automatically turn off as a safety feature. The collar will
be ready to be reactivated once the button has been released.
Pager Button
The Pager buttons are located on the face of the transmitter.
The orange button corresponds with the orange receiver
collar and the gray with the black receivercollar. Pressing it
will give non-stimulating vibration as long as the button is
depressed, for up to 12 seconds.

14
3. Collar tting
The receivercollar should be ¿tted so that the surgical
stainless steel contact points press ¿rmly against the dog’s
skin. When properly ¿tted, you should be able to ¿t a ¿nger
or two snugly in between the contact points and your dog’s
skin. When properly ¿tted, the receivercollar should not
move on the dog. The best location for the receivercollar
box is either side of the dog’s windpipe.
A loose ¿t can allow the receivercollar to move around
on the dog’s neck. When this happens, the contact points
may rub the skin and cause irritation. If the receivercollar
is too tight, the dogs may have dif¿culty breathing.

15
4. How to nd the right stimulation
The 1900S comes with the rheostat dial on the transmitter.
The rheostat intensity dial controls the stimulation level,
with level 0 being the lowest level and level 127 being the
highest.
The level of stimulation best suited for your dog depends
on your dog’s temperament and threshold for stimulation.
Always start at the lowest level and work your way up. The
appropriate level can be found when the dog responds to
the stimulation with a mild reaction, such as a tensing of the
neck muscles. The stimulation level may vary depending
on the training situation. When highly distracted, dogs will
require a higher level of stimulation.
NOTE : The stimulation intensity can be adMusted even
while the stimulation is in use.
5. To maximize the distance
The Dogtra 1900S has a 34-mile range. The range may
vary depending on the way the transmitter is held. Hold
the transmitter away from your body to receive the greatest
range. For maximum signal strength, keep the Dogtra
1900S properly charged.
*Avoid touching the antenna or the range may decrease
substantially.
Maximum range Typical range Minimum range

16
6. The LED indicator
The LED indicator Àashes every 4 seconds when the
receiver is on and ready for use. The LED indicator will
blink on both the transmitter and the receiver when the
transmitter buttons are pressed.
The LED indicator color indicates the battery life level.
Green = Fully charged, Amber = Medium, Red = 1eeds
charging
If the unit is used while the LED indicator is red, it will shut
down automatically.
Receiver Indicator Light
When the ³Constant´button on the transmitter is pushed,
the collar indicator light will glow steadily (either green,
amber, or red based on the remaining battery life), as long
as you hold the button down, for up to 12 seconds.
When the ³1ick´button is pushed, the light comes on for
a fraction of a second.

17
7. Charging the battery
The Dogtra 1900S uses Lithium-Polymer batteries.
1. Charge the unit before using the unit for the ¿rst time.
2. Do not charge the batteries near any Àammable
substances.
3. Fully charge the batteries if the unit is to be stored
without use for a period of 3 months or more.
Recharge the unit if :
1. The indicator light on the collar is emitting a red color.
2. If the 3 bar indicator on the transmitter LCD shows Must
1 bar.
3. The indicator light on the transmitter or receiver will not
come on. The indicator light on the transmitter or receiver
comes on momentarily, but will not stay on when the
³Constant´button is pushed.
Battery Charging Procedure
NOTE : The unit has a partial charge when it leaves the
Dogtra facility, upon receipt of the collar, be sure to give it
a full 2-hour initial charge before the ¿rst use.
1. Attach the charging cables to both the transmitter and
receiver(s), as shown on page 17.

18
2. Plug the charger into a 120-volt wall outlet or if using
the accessory ¿eld charger, plug into a cigarette lighter
only for Lithium-Polymer batteries (use a 230-volt
European charger for Europe.). When properly plugged
in, all indicator lights should glow red. During the
charging process, the unit will shut off. 2nce the battery
cable is unplugged from the unit after a full charge,
you will need to turn the unit on again before use.
3. The Lithium-Polymer battery is fully charged within
2 hours. The lights will stay red during the charging
process. The red light will change into a steady green light
when the battery is fully charged (when you disconnect
the charger after ¿nishing the charge, you will need to
restart the unit).
4. After charging, cover the battery charging receptacles
with the rubber plugs on the transmitter and receiver
collar.
NOTE : 2nly use Dogtra-approved batteries, chargers, and
accessories for your Dogtra e-collars. When a charger is not
in use, disconnect it from the power source.
8. The handheld transmitter LCD

19
Turn the LCD backlight on and off with a short press of
the onoff button.
The LCD screen indicates the stimulation level (0-127).
The LCD battery life indicator shows 3 bars at full charge,
2 bars at medium charge and 1 bar when it needs to be
charged. The battery life indicator only speci¿es the
remaining charge for your transmitter. To ¿nd the remaining
charge for your receiver, observe the LED indicator on the
receivercollar.
Green = full charge
Amber = medium charge
Red = needs charge
Care for LCD Transmitters in Cold Temperature
In cold temperatures (10 degrees F or below), the Liquid
Crystal Display (LCD) on your transmitter may be dim
or slow to respond. Wait until the display becomes visible
before selecting any training level. Even though the LCD
screen might be dim or slow to respond when you push the
1ick or Constant button, the transmitter will still function
properly. In the occurrence of extremely cold weather, the
LCD screen might take a moment to respond causing the
intensity level to freeze at that current level. In this situation,
if you turn the rheostat intensity dial, the level on the screen
may not change but the actual intensity from the receiver
collar will change in agreement with the dial. In this
situation, it is ideal to either wait until your transmitter is
back to working order before emitting a correction, or while
holding the constant button down slowly turn the Rheostat
Intensity Dial while watching your dog’s reaction. Do not
turn the Rheostat Intensity Dial at a rapid increase because
the receivercollar will emit a static correction based on the
level of the Rheostat Intensity Dial, which might not be
correctly reÀected on the LCD screen.