Dogtra 200C User manual

1
200C
AVAILABLE IN 2-DOG SYSTEM: 202C
Owner's Manual
Please read this manual thoroughly
before operating the 200C training e-collar.

5
Optional Accessories
Belt Clip
A belt clip is available for the handheld transmitter.
Auto Charger
The auto charger for the 200C has an input of 12-volts to
24-volts and has an output of 5-volts 1000mAh.
European Charger
Dogtra’s European chargers are designed for use with a
220 volt AC electrical outlet.
To purchase accessories, please visit www.dogtra.com or
call customer service at [phone].
AT A GLANCE
Owner's
Manual
ReceiverTransmitter Battery
Charger
Splitter
Cable

6
• 1/2-mile range
• IPX9K waterproof certified
• Medium output receiver
• 100 stimulation levels/front-facing Rheostat Dial
• Two stimulation types: Nick & Constant stimulation
• HPP (High Performance Pager) vibration
• Enhanced contact points
• Ultra-compact receiver
• For dogs as small as 10 lbs
• 2-hour rapid charge lithium polymer batteries
MAIN FEATURES

7
OVERVIEW
200C
Transmitter
Rheostat Dial
Battery Charging
Receptacle &
Rubber Plug
Pager Nick
Constant
On/Off
Magnetic
Red Dot
Antenna
LED
Indicator
Light

8
Battery Charging
Receptacle &
Rubber Plug
2nd Dog
Pager
(Orange
Button)
1st Dog
Pager
(Gray
Button)
1st Dog
Nick & Constant
(Gray Button)
LED
Indicator
Light
Nick/Constant
Toggle Switch
2nd Dog
Nick & Constant
(Orange Button)
On/Off
Magnetic
Red Dot
Rheostat Dial
Antenna
202C
Transmitter

9
Contact Points
Collar Strap
On/Off Magnetic
Red Dot
Battery Charging
Receptacle &
Rubber Plug
LED
Indicator Light
200C, 202C
Receiver

10
UNDERSTANDING YOUR
TRAINING SYSTEM
1. Turning the 200C On/Off
To turn the receiver on, place the red dot on the back of
the handheld transmitter to the red dot on the receiver.
Hold the two red dots together for a moment until the
LED light on the receiver comes on.
To turn the receiver off, repeat the same procedure
holding the two red dots together momentarily. The LED
light will turn red for a brief moment indicating that the
receiver is now off.
The transmitter does not have an on/off button and it will
only activate when the buttons are pressed.

11
Pager
Nick
Constant
200C
The transmitter for the 200C single dog unit has three
buttons (one on the face of the transmitter and two on the
left side).
2. Transmitter Button Function
Nick Button
The Nick button is located on the top of the left side of the
handheld transmitter. When the Nick button is pressed,
the receiver emits a single rapid pulse of electrical
stimulation.
Constant Button
The Constant button is located on the bottom of the left
side of the handheld transmitter. Pressing the Constant
button gives continuous stimulation as long as the
button is pressed, for up to 12 seconds. If the button
is not released after 12 seconds, the stimulation will
automatically turn off as a safety feature. The receiver
will be ready to be reactivated once the button has been
released.
Pager Button
The Pager button is located on the face of the transmitter.
Pressing it will give a vibration for as long as the button is
pressed, for up to 12 seconds.

12
Nick/Constant
Toggle Switch
2nd Dog Pager
(Orange Button)
1st Dog Pager
(Gray Button)
1st Dog
Nick & Constant
(Gray Button)
2nd Dog
Nick & Constant
(Orange Button)
202C
The 202C two-dog unit has four buttons and a toggle
switch on the transmitter (two on the face of the
transmitter and two on the left side).
Nick & Constant Toggle Switch
Located on the face of the transmitter is a toggle switch.
The toggle switch has a setting for Nick and another for
Constant. The color-coordinated buttons (orange for
the orange receiver and gray for the black receiver) will
implement the desired stimulation based on the toggle
switch setting.
When either the orange or gray stimulation button is
pressed and the toggle is set on Nick, the receiver emits a
single pulse of electrical stimulation.
When you press either the orange or gray stimulation
button and the toggle is set on Constant, the receiver
emits a continuous stimulation as long as the button is
pressed, for up to 12 seconds. If the button is not released
after 12 seconds, the stimulation will automatically turn
off as a safety feature. The receiver will be ready to be
reactivated once the button has been released.

13
Pager Button
The Pager buttons are located on the face of the
transmitter. The orange button corresponds with the
orange receiver and the gray with the black receiver.
Pressing it will give a vibration as long as the button is
pressed, for up to 12 seconds.
3. Receiver Fitting
Proper Fit
The receiver should be fitted so that the medical grade
stainless steel contact points press firmly against
the dog’s skin. You should be able to fit two fingers
underneath the collar strap. The best location is on either
side of the dog’s windpipe.
Improper Fit
A loose fit can allow the receiver to move around on the
dog’s neck. When this happens, the contact points may
rub against the skin and cause irritation. If the receiver is
too loose, the contact will not be consistent and cause the
corrections to be inconsistent. Dogtra uses medical grade
stainless steel contact points and anti-microbial plastic to
protect the dog’s skin.

14
The 200C has a Rheostat Dial
on the front of the transmitter
(0 is the lowest and 100 is
the highest). Remember that
you will need to adjust the
setting (upward or downward)
depending on your dog’s
temperament and threshold
4. Finding the Right Stimulation
for stimulation. Always start at the lowest level and work
your way up. The appropriate level can be found when the
dog responds to the stimulation with a mild reaction. Also,
as the dog’s attitude changes, especially during times
of increased excitement or distraction, you may need to
adjust the intensity level.
NOTE : The stimulation intensity can be adjusted even
when the stimulation is in use.
Attention!
Leaving the receiver in the same location on the
dog’s neck for an extended period of time can cause
skin irritation due to the sensitivity from the contact
points. If the dog is to wear the receiver for long
periods, occasionally reposition the receiver every
few hours so that the contact points are moved to a
different location on the dog’s neck and remove the
receiver after 8 hours of usage. Make sure you check
for skin irritation each time you use the unit.

15
The 200C has a 1/2-mile range. Depending on the way
you use your transmitter, the transmitter range may vary.
To get the greatest range, hold the transmitter away from
your body and avoid touching the antenna. Keep your unit
properly charged for maximum signal strength.
5. Maximizing the Distance
Typical range
Maximum range Minimum range

16
6. LED Indicator
The LED indicator flashes every 4 seconds when the
receiver is on and ready for use. The LED indicator will
blink on both the transmitter and the receiver when the
transmitter buttons are pressed.
The LED indicator color indicates the battery life level.
Green = Full charge
Amber = Medium charge
Red = Needs charge
If the unit is used while the LED indicator is red, it may
shut down automatically.
Receiver Indicator Light
When the Constant button on the transmitter is pressed,
the receiver indicator light will glow steadily (either green,
amber, or red based on the remaining battery life), as
long as you hold the button down, for up to 12 seconds.
When the Nick button is pressed, the light comes on for a
fraction of a second.

17
The Dogtra 200C uses a lithium polymer battery.
Recharge the unit if the indicator light is red or does not
come on, or the system will not stay on when any button
is pressed.
NOTE 1: Only use Dogtra-approved chargers and
accessories for your Dogtra e-collars. This will prevent any
damage that can be incurred from attempting to use
a different charger.
NOTE 2: The unit has a partial charge when it leaves the
Dogtra facility. Upon receipt of the system, be sure to give
it a full 2-hour initial charge before the first use away from
any flammable substances.
NOTE 3: When a charger is not in use, disconnect it from
the power source. Fully charge the batteries if the unit is
to be stored without use for a period of 3 months or more.
Charging Cable
120 Volt
Charger
Wall Outlet
7. Charging the Battery

18
Follow the steps below to charge your system:
1. Open the rubber plugs on the battery charging
receptacles and plug in the charging cable.
2. Plug the charger into a 120-volt wall outlet or, if using
the auto charger, plug into a cigarette lighter only for
lithium polymer batteries (use a 220 volt European
charger for Europe). All indicator lights should glow red
when properly plugged in and the unit will automatically
shut off during the charging process. You will need to
turn the unit on again before use once the unit is fully
charged and unplugged from the battery cable.
3. The lithium polymer battery is fully charged within
2 hours. The lights will stay red during the charging
process and turn green once the unit is fully charged.
4. After charging, cover the battery charging receptacles
with the rubber plugs.

19
GENERAL TRAINING TIPS
Your dog must know some basic obedience commands
before beginning training with the 200C. A dog learns
by first being shown a command, followed by lots of
repetition over an extended period. As the dog becomes
proficient at these commands, the trainer can introduce
distractions and different locations to strengthen them.
Obedience Training on the Leash
Your dog must fully understand the obedience commands
(sit, stay, here, heel, and kennel) before using the e-collar
for reinforcement of these commands. A leash attached
to a standard collar is used to "teach" the dog the basic
obedience commands (here, heel, sit, and stay). A tug
on the leash/collar is used to reinforce the command.
When the dog complies with the command, use positive
reinforcement/praise. Once the dog understands these
commands, the e-collar can be used to reinforce them.
Beginning E-Collar Training
When you feel your dog understands the obedience
commands on the leash we can now start with the e-collar
training. With the dog on the leash and wearing the
e-collar, continue with your obedience drills. Apply light
stimulation (Nick or Constant) when a command is given;
the stimulation can be removed as the dog complies.
Through repetition, the dog learns to perform the
command.
The final step is the avoidance phase in which the
dog learns that he can avoid the stimulation altogether
by performing your commands. When these training

20
procedures are complete, the e-collar is used as a reminder
when the dog does not comply with your commands at
home or in the field. Keep your initial training sessions
short and positive as dogs have a short attention span.
How Much Stimulation to Use
Always start with low levels of stimulation and work
your way up depending on the disposition of your dog
and the given situation. By using the correct amount of
stimulation to get your point across, you will have a more
controllable environment and a dog that is under less
stress. Animals (and humans) perform better in a less
stressful environment.
For more training information, please visit our website at
www.dogtra.com.

21
MAINTENANCE
Basic Maintenance
Make sure the rubber charging cap is securely in place
when the system is in use. After each training session,
carefully inspect the unit for any missing parts or
damage to the casing. Damaged or broken casing may
aect the waterproof guarantee on the unit. After
confirming that there is no damage to the casing, rinse
the receiver and clean out any dirt or debris.
Storage Maintenance
The unit should be fully charged before storing for
extended periods. While in storage, the unit should be
given a full charge once a month and before the first use.
Store the units in room temperature. Do not keep the
units exposed to extreme climates.
Troubleshooting
If the unit is malfunctioning, please refer to the
“Troubleshooting Guide” before sending it to Dogtra for
service. If you have any questions or concerns, you may
email them to [e-mail], or call customer service
at [phone].

22
TROUBLESHOOTING GUIDE
1. My dog is not reacting to the system.
- Make sure the receiver and transmitter are on.
- Make sure the collar strap is tight enough so both
contact points are touching the dog’s skin.
- The contact points may be too short for the dog. To
place an order for longer contact points that are more
appropriate for your dog, please call (888) 811- 9111.
If you are already using the longest contact points
available, you might need to trim down the hair on the
dog’s neck so both contact points are touching the
dog’s skin.
- The intensity level may be too low for your dog. Keep
increasing the stimulation until the dog responds,
usually with neck movement, head shaking, looking
over its shoulder, etc. (response may be very subtle).
2. The LED indicator light comes on, but I do not feel any
stimulation.
- Testing the system at various levels using the test light
is the best way to test your system. Your tolerance may
be higher than the level you are testing yourself.
- The battery may be low, so check the LED light for
battery life.

23
3. The transmitter has no range or stimulation is less
when the dog is farther away.
- The antenna(s) may be damaged. To order parts, please
contact customer service at [phone] or go to
www.dogtra.com.
- The range indicated on the unit’s box is for flat terrain.
Heavy brush, trees, hills, or moisture will affect the
range of your unit. For best range, hold the transmitter
vertically above your head, and/or try moving to higher
ground.
- Any electrical conductors will affect the range, such as
cars, chain-link dog runs, metal structures, and radio
towers. For best results, operate away from these items.
4. My unit is not holding a charge.
- The batteries might not be charged properly, or the
charger, splitter, and the charging port may not be
functioning properly. You can send in your charging
units to have us inspect them.
- The charging pin may be damaged. Inside the charging
port, there is a metal pin that should be standing
straight up and stiff. If the pin is wobbling, broken, or
missing, you will need to send the unit in to the Repair
Department. The charging port must be clean prior
to charging; clean the dirt out with a cotton swab and
some rubbing alcohol. If the dog is in salt-water, be sure
to rinse the receiver and charging port with clean water.
- If the above does not resolve your issues, contact
Dogtra customer service at [email protected] or
[phone].