Dogtra Advance 2302NCP Service manual

REMOTE CONTROLLED
DOG TRAINING COLLARS
www.dogtra.com
Copyright c 2008 Dogtra Company
22912 Lockness Avenue
Torrance, CA 90501
U.S.A.
telephone (310) 534 - 0101
fax (310) 534 - 9111
toll free 1-888-811-9111
2008 -

1
CONTENTS
Code setting for your newly replaced
2300NCP Advance Transmitter (One-Dog)
Code setting for your newly replaced
2300NCP Advance Receiver (One-Dog)
Code setting for your newly replaced
2302NCP Advance Transmitter (Two-Dog)
Code setting for your newly replaced
2302NCP Advance Black Collar/Receiver for
(Two-Dog)
Code setting for your newly replaced
2302NCP Advance Orange Collar/Receiver for
(Two-Dog)
1
2
2
5
5
Once you have received the transmitter that was sent to you
by the Dogtra facility, you need to code set your unit to control
your Receiver with the new Transmitter.
The code setting method is as follows:
1) Turn the Transmitter on by
pushing the ON/OFF Switch
located on the right side then
select the level 0 with the
Intensity Selection Dial.
2) Place the red dot on the back of
the transmitter to the red dot on
the collar/receiver. Hold the two
red dots together for about 5
seconds or more. Release them
when the green LED blinks fast
on the collar/receiver.
3) Within 5 seconds after releasing
the transmitter and the receiver,
hold the Nick button and the
Constant button together located
on the left side of the transmitter
for 3 seconds, or until the rapid
green blink resumes to a slower
paced green blink. The LED
indicator light blinks once every 4 seconds after staying on
green for about a second. Now the setting work is completed.
Together
Code setting for your newly replaced
2300NCP Advance Transmitter (One-Dog)

3
2
Once you have received the collar/receiver that was sent to
you by the Dogtra facility, you need to code set your unit to
control the new Receiver with your Transmitter.
The code setting method is the same as the procedure
described on Code setting for your newly replaced 2300NCP
Advance Transmitter(One-Dog)
Once you have received the transmitter that was sent to you
by the Dogtra facility, you need to code set your unit to control
your Black Collar/Receiver and Orange Collar/Receiver with
the new Transmitter.
The method of the code setting is as follows:
Code setting for your Black Collar/Receiver:
1) Turn the Transmitter on by
pushing the ON/OFF Switch
located on the right side then
select the level 0 with the
Intensity Selection Dial.
Code setting for your newly replaced
2300NCP Advance Receiver (One-Dog)
Code setting for your newly replaced
2302NCP Advance Transmitter (Two-Dog)
2) Set the Nick/Constant Toggle
Switch on the front of the
transmitter on the N position.
3) Place the red dot on the back of
the transmitter to the red dot on
the Black collar/receiver. Hold
the two red dots together for
about 5 seconds or more.
Release them when the green
LED blinks fast on the
collar/receiver.
4) Within 5 seconds after releasing
the transmitter and the receiver,
hold the Black button and the
Orange button on the left side of
the transmitter together for 3
seconds, or until the rapid green
blink resumes to a slower paced
green blink. The LED indicator
light blinks once every 4 seconds after staying on green for
about a second. Now the setting work is completed.
Together

5
Code setting for your Orange Collar/Receiver:
1) Turn the Transmitter on by
pushing the ON/OFF Switch
located on the right side then
select the level 0 with the
Intensity Selection Dial.
2) Set the Nick/Constant Toggle
Switch on the front of the
transmitter on the C position.
3) Place the red dot on the back of
the transmitter to the red dot on
the Orange collar/receiver. Hold
the two red dots together for
about 5 seconds or more.
Release them when the green
LED blinks fast on the
collar/receiver.
4) Within 5 seconds after releasing
the transmitter and the receiver,
hold the Black button and the
Orange button on the left side of
the transmitter together for 3
seconds, or until the rapid green
blink resumes to a slower paced
green blink. The LED indicator
light blinks once every 4 seconds after staying on green for
about a second. Now the setting work is completed.
4
Code setting for your newly replaced
2302NCP Advance Black Collar/Receiver for (Two-Dog)
Once you have received the orange collar/receiver that was
sent to you by the Dogtra facility, you need to code set your unit
to control the new Orange Collar/Receiver with your
Transmitter.
The code setting method is the same as the procedure
introduced on the page 4 Code setting for your Orange
Collar/Receiver.
Once you have received the black collar/receiver that was sent
to you by the Dogtra facility, you need to code set your unit to
control the new Black Collar/Receiver with your Transmitter.
The code setting method is the same as the procedure
introduced on the page 2 Code setting for your Black
Collar/Receiver.
Code setting for your newly replaced
2302NCP Advance Orange Collar/Receiver for (Two-Dog)
Together