Dogtra EF3000 User manual

1
CONTENTS
Ҷ
Ҷ
Ҷ
Ҷ
Ҷ
Ҷ
Ҷ
Ҷ
Ҷ
Ҷ
Ҷ
Ҷ
Ҷ
Ҷ
Ҷ
OVERVIEW
MAIN FEATURES
SAFETY FEATURES
PACKAGE CONTENTS
DESCRIPTION OF TRANSMITTER PARTS
DESCRIPTION OF COLLAR PARTS
CHARGING THE RECEIVER/COLLAR
TESTING YOUR
PRIOR TO INSTALLATION
INSTALLATION
ADDITIONAL PARTS
WIRE SPLICING
TROUBLESHOOTING
GENERAL MAINTENANCE TIPS
OPTIONAL ACCESSORIES
WARRANTY AND REPAIR INFORMATION
2
2
3
3
4
9
14
16
17
19
22
24
26
27
29

3
PACKAGE CONTENTS
2
The system gives you the ability to allow your dog
the freedom he wants, within your specified boundaries. Dogtra’s
containment system contains your dog without the use of conventional
fencing that can be chewed through, jumped over or dug under.
The width of the signal field can easily be adjusted at the wall-mount
transmitter. The strength of the electrical stimulation can be adjusted on
each separate receiver with the intensity selection dial. In the
ūStimulation OnlyŬmode, your dog will receive stimulation only. In the
ūPager+StimulationŬmode, your dog will receive a silent
pager/vibration, followed by stimulation when he approaches the
boundary area. Once your dog consistently avoids the signal boundary,
the stainless steel contact points can be replaced with the plastic training
probes. With the plastic training probes, your dog will be able to respond
to the vibration warning without receiving any electrical stimulation.
Accessories for the system such as additional wire,
flags, lightning/surge protector, and the European 220-volt battery
charger, are available by calling Dogtra Company at 1-888-811-9111
(8:30am-4:00pm PST).
OVERVIEW
OVERVIEW
şWaterproof receiver/collar.
şPager/vibration signal that warns the dog prior to electrical
stimulation/correction.
şWire continuity indicator shows that the fence is in operational
condition.
şIntensity selection dial on each individual receiver/collar that offers
levels (1-5) to match each dog’s personality and temperament.
şStimulation is discontinued after 8 seconds for safety purposes. The
collar will be reactivated when the dog approaches the boundary again.
şEasy to add additional Receiver/collar.
ş2-hour rapid charge.
şSystem turns to sleep mode to save energy and power when your dog
is playing safely within the eF-3000 GOLD boundary.
şRechargeable receiver.
şLong-range signal (will work up to 40 acres).
şUser-friendly controls.
MAIN FEATURES
şDogtra’s eF-3000 GOLD system collars use state-of-the-art
microcomputer technology. The receiver has an automatic control that
limits the stimulus to ten seconds.
şDogtra’s filtering system prevents reception from outside sources other
than your transmitter.
SAFETY FEATURES
şWall-Mount Transmitter
şReceiver/collar
şTransmitter Adaptor (25-volt 500mA)
şReceiver Adaptor (5-volt 1A)
şTest Lamp
şBoundary Training Flags (50 ea.)
ş18ga Underground Fence Wire (500 feet)
şSplices (4 ea.)
şGround Wire (green)
şTransmitter Mount Screws (2 ea.)
şPlastic Anchor (2 ea.)
şPlastic Training Probes (2 ea.)
şLonger Contact Points (2 ea.)
şOwner’s Manual
şTraining Book
PACKAGE CONTENTS

45
DESCRIPTION OF TRANSMITTER PARTS
TRANSMITTER
TRANSMITTER
transmitter
Wire Indicator Light
ON/OFF Indicator Light
Adaptor Jack
Connector
Connector for Ground Wire
Wire Connectors for
Splicing
Field Width
Adjustment Knob
ON/OFF & Function
Selection Switch
ON/OFF & Function Selection Switch
ON/OFF & function selection switch has three functions. When the
toggle switch is in the up position, the unit will give the dog a
pager/vibration followed by stimulation correction. When the toggle
switch is in the down position, only stimulation occurs (without the pager
warning). When the switch is in the middle position, the power is off.
Pager+Stim
OFF
Stimulation
Pager+Stimulation
ON/OFF & Function Selection Switch
OFF
Stimulation
Field Width Adjustment Knob
This knob controls the width of the signal field (the distance from the
boundary wire to the location where the receiver/collar first activates).
Turning the knob clockwise increases the field width, giving your dog a
wider area before the activation begins. Turning it counter-clockwise
decreases the signal field, thus giving the dog a shorter area prior to
activation.
Field Width Adjustment Knob

7
6
TRANSMITTERTRANSMITTER
ON/OFF Indicator Light
When the ON/OFF & function selection switch is either in the up or
down position the ON/OFF indicator light will be on, indicating that the
power is on. When the switch is in the middle position the light goes off,
indicating that the power is off.
ON/OFF Indicator Light
Wire Indicator Light
When the wires are connected properly, the wire indicator light will be
on. In the event that the eF-3000 GOLD wire becomes damaged or
disconnected the light will automatically turn off.
Wire Indicator Light
Wire Connectors For Splicing
The easy-to-use push-release wire connectors let you instantly connect
or disconnect the boundary wire leads. Wires should be stripped
approximately a half-inch before being inserted into the red connectors
on the bottom of the wall mount transmitter. The
system comes with a ground wire to protect the unit in the event of
lightning/power surge. Strip about a half-inch on each end of the ground
wire and insert one end into the black connector on the bottom of the
wall transmitter. The other end should be buried into the ground or
wrapped around a water pipe and secured with electrical tape.
Option : A lightning/surge protector can be purchased if there are no
grounding options near the wall transmitter.
Wire Connectors

9
COLLAR
8
TRANSMITTER
Wall-Mount Transmitter
Use the (2) included screws to mount the transmitter to a wall securely
near an outlet. The unit will withstand freezing temperatures, but it is not
waterproof. Therefore, we recommend mounting the transmitter in a safe,
dry sheltered area such as a shed, garage or carport. Plastic anchors have
been provided to secure mounting onto drywall. Use a 1/4ƃdrill bit to
make holes into the drywall. Insert the anchors into the holes so that the
open end faces out and mount the transmitter by inserting the screws into
the open end of the anchors.
To power the wall transmitter, plug the AC daptor into the standard 120-
volt outlet and connect it to the adaptor receptacle of the transmitter.
120-volt
25V 500mA
DESCRIPTION OF COLLAR PARTS
Indicator Light
Contact Points
Battery Charging
Receptacle
Intensity Selection Dial
Collar Strap
Receiver
Adaptor Receptacle
Adaptor Receptacle
Plug the 120-volt adaptor into a 120-volt wall outlet and insert the adaptor
plug into the adaptor receptacle of the transmitter.

11
COLLAR
10
COLLAR
Receiver Indicator Light (LED)
When first activating the eF-3000 Gold system, the LED light on the
receiver/collar will illuminate for approximately 1 second to indicate that
the power is on. 2 seconds after the initial light, a blink will occur every 2
seconds to indicate that the receiver/collar is functioning properly.
(Green = full charge, Amber = medium charge, Red = needs charge)
The color of the LED indicates the battery life of the receiver.
When the collar does not receive a signal from the transmitter for 10
seconds or more, the receiver/collar will go into sleep mode, and the LED
light will stop blinking.
When your dog gets close to the wire boundary, the indicator light will
blink steadily to indicate that a stimulation is being activated depending
on the stimulation selection that you have chosen on the wall-mount
transmitter.
Intensity Selection Dial
The stimulation level is adjustable from each individual dog’s
receiver/collar so that it is easy accommodate each dog’s different
personality and temperament.
The stimulation levels range from level 1 to level 5, level 1 being the
lowest.
In order to select the proper intensity level for each dog, we recommend
that you begin at level 1 and continue to increase the level slowly until
you are able to notice a reaction from your dog. This ensures that you
select a level that is appropriate for your dog.
When you place the knob at the OFF position, the collar is completely
shut off.
In order to maintain full use of the batteries in the collar, please turn off
the receiver/collar when your eF-3000 Gold system is not being utilized.

13
COLLAR
12
COLLAR
PROPER FIT
The collar should be fitted so that the surgical stainless steel contact
points press firmly against the dog’s skin. You should be able to fit a
finger in between the contact point and your dog’s skin. The best location
is either side of the dog’s windpipe.
IMPROPER FIT
A loose fit can allow the collar to move around on the dog’s neck. When
this happens, the contact points may rub the skin and cause irritation. If
the collar is too loose, electrical contact will be inconsistent and your
corrections will be inconsistent also.
Dogtra uses surgical stainless steel contact points and Anti-microbial
plastic to protect the dog’s skin.
ATTENTION!
Leaving the receiver/collar in the same location on the dog’s neck, for an
extended period of time can cause skin irritation. If the dog is to wear the
e-collar for long periods, occasionally reposition the collar so that the
contact points are moved to a different location on the dog’s neck. Make
sure you check for skin irritation, each time you use the unit.
Receiver/collar Battery Charging Receptacle
On the inside of the receiver/collar, next to the collar strap, is a battery
charging receptacle with a rubber plug.
The unit will be fully waterproof with or without the rubber plug. If the
dog was in salt-water, be sure to rinse the receiver and charging port with
clean water, and let air dry.
Adaptor
The battery charger is designed for a 120-volt wall outlet (An European
220-volt AC charger is also available.).
Transmitter Adaptor
(25-Volt 500mA) Receiver Adaptor
(5-Volt 1A)

15
14
CHARGING THE RECEIVER/COLLAR
uses Lithium-Polymer batteries.
1. Charge the unit before using the unit for the first time.
2. Do not charge the batteries near any flammable substances.
3. Fully charge the batteries if the unit is to be stored without use for a
period of 3 months or more.
Recharge the unit if :
- The LED indicator light on the receiver/collar is emitting a red color.
- The indicator light on the receiver will not come on.
- The indicator light on the receiver comes on momentarily, but will not
stay on near the wire.
CHARGING THE RECEIVER/COLLAR
CHARGING THE RECEIVER/COLLAR
Battery Charging Procedure
Note : The unit has a partial charge when it leaves the Dogtra facility,
upon receipt of the collar, be sure to give it a full 2-hour initial
charge before the first use.
1. Attach the charging cables to the receiver as shown.
2. Plug the charger into a 120-volt wall outlet.
When properly plugged in, all indicator lights should glow red.
During the charging process, the unit will shut off. Once the battery
cable is unplugged from the unit after a full charge, you will need to
turn the unit on again before use.
3. The Lithium-Polymer battery is fully charged within 2 hours. The
lights will stay red during the charging process. The red light will
change into a steady green light when the battery is fully charged.
(When you disconnect the charger after finishing the charge, you will
need to restart the units).
4. After charging, cover the battery charging receptacles with the rubber
plugs on the transmitter and receiver.
Note : Only use Dogtra-approved batteries, chargers, and accessories for
the . When a charger is not in use,
disconnect it from the power source.

17
16
INSTALLATION
1. To ensure that your system is working properly,
connect the transmitter adaptor into the adaptor of the transmitter and
then plug the adaptor into a household outlet. Switch the stimulation
knob to Pager+Stimulation, or Stimulation Only. The ON/OFF
indicator light should turn on.
2. Unwind the length of ground wire that was provided and strip about 1/2
inch off each end. Insert both ends of the ground wire into the outer, red
wire connector jacks, leaving the center jack free. If the wires are
connected properly, the wire indicator light will be on.
3. Next, activate the receiver/collar by turning the intensity level dial on
the receiver to the desired level. The LED light will blink once every
two seconds showing that it is on.
ҳIf not activated for 10 seconds or more, the system will go into sleep
mode.
4. Hold the receiver in your hand with the contact points facing up. Place
the test lamp over the contact points and approach the test loop.
5. Watch for the test lamp to come on and/or the unit will emit the
warning vibration if the unit is in this mode at the wall mount
transmitter. Be careful not to touch the contact points as the unit will
emit stimulation when activated.
TESTING YOUR
PRIOR TO INSTALLATION
TESTING
Fence Wire
The fence wire must make a continuous loop around your property for
your system to operate. The signal is delivered from the terminal of the
transmitter, through the fence wire, back to the other terminal on the
transmitter. When this is accomplished, the wire continuity light will emit
a constant red indicator.
INSTALLATION