Dogtra YS 600 User manual

Owner’sManual
BUILT RELIABLE

1
By Dogtra
No Bark Collars
Owner's Manual
Please read this manual thoroughly
before using the YS600.

2
Product Safety and Health Statement
1. The YS600 is intended to prevent the barking of dogs
only. It is NOT intended for use on people or on animals
other than dogs. Dogtra does not assume any liability for the
improper use of the YS600.
2. Leaving the YS600 in the same position on a dog’s neck
for extended periods of time can cause skin irritation. To
prevent this, occasionally reposition the unit so the contact
points are moved to a different location on the dog’s neck.
ALWAYS check your dog’s neck for signs of skin irritation
when using the YS600.
3. A proper t is necessary for the YS600 to work optimally.
Both contact points must be in contact with your dog’s skin
at all times for a consistent stimulation. A loose tting collar
can cause the contact points to rub against the skin and cause
irritation.
4. The YS600 is not intended for use on dogs weighing less
than 35 pounds or less than 6 months of age.
5. Please remove the YS600 before playing with your dog. The
activity may cause your dog to bark, which could lead him/her
to associate playing with the electrical stimulation.
6. Closely monitor your dog’s activity and stimulation
output while using the YS600. When removing the YS600
from your dog’s neck, make sure your dog is not barking and
in a calm or stable condition.

3
Table of Contents
At a Glance .......................................................
Main Features ....................................................
Overview ..........................................................
How to Use the On/Off & Intensity Dial ..................
The LED Indicator ..............................................
Operating Modes .................................................
The Persistent Bark Indicator ................................
Testing the YS600 ...............................................
Charging the Battery ..........................................
Collar Fitting ...................................................
Troubleshooting Guide ......................................
Warranty and Repair Information .........................
4
4
5
6
7
7
8
9
10
11
12
14

4
At a Glance
Main Features
YS600
No Bark Collar
Battery
charger
O w n e r ’s
Manual
Contoured Design
Receiver/Collar
101 Intensity Levels
1-10
Persistent Bark
Indicator
Accelerometer
Bark Sensor
Non-Stimulating
High Performance
Pager
For Dogs as Small
as 35 lbs.
Low to High Power
Stimulation
Enhanced Contact
Points
Fully Waterproof
2-Hour Rapid
Charge Batteries

5
Overview
LED Indicator
Light
On/Off and
Intensity Dial
Sensor
Contact Points
Battery Charging
Receptacle &
Rubber Plug
Collar Strap

6
How to Use the On/Off & Intensity Dial
- The On/Off Intensity Dial is used to turn the No Bark Collar
on/off and to select the stimulation intensity level.
-Set the dial to “.” to turn off the No Bark Collar.
- Set the dial to “P” for non-stimulating vibration only mode.
- The No Bark Collar has stimulation levels 1 (lowest) through
10 (highest). Each stimulation level begins with a vibration and
is followed by the stimulation.
- Set the dial to “T” to test the No Bark Collar. See Testing the
YS600 on page 9 to check if your unit is working properly.
NOTICE
When rst using the YS600 No Bark Collar, it is recommended
to start at the lowest stimulation intensity level. If your dog
continues to bark, gradually increase the stimulation intensity
level. Closely monitor you dog’s reaction to nd the right
stimulation level for you dog.
On/O & Intensity Dial Function
•Power O
PNon-Stimulating Vibration
1~10 Stimulation Level
T Test mode

7
The LED Indicator
The LED indicator will ash for 1 second when the YS600
has been turned on, and every 4 seconds afterwards. If your
dog does not bark for over 30 seconds, the LED indicator will
turn off and the YS600 will go into a sleep mode to conserve
battery life. It will reactivate when your dog barks and a
vibration/correction needs to be made.
Before going into Sleep mode, the LED light ashes green
when the battery is fully charged and turns to amber when the
battery life is getting low.
When the LED indicator emits a blinking red light, the battery
needs to be recharged.
Operating Modes
1. Non-Stimulating High Performance Pager (P)
- The YS600 will vibrate twice when your dog barks. It will not
send a stimulation when set to “P”.
2. Stimulation Intensity Levels (1-10)
- The YS600 will vibrate once followed by stimulation when
your dog barks.
* There is a 15 second delay between stimulation on levels
1-10 and vibration on P mode.
Battery life
LED window
Fully charged Medium charge Needs charge
On Working Green Yellow Red
On Charging Green Red Red

8
The Persistent Bark Indicator
The Persistent Bark Indicator activates when the unit is
turned off and when there has been excessive barking.
1. Without excessive barking:
– The LED will glow red for 2 seconds when the unit is
turned off.
2. With excessive barking:
– The LED will blink green for 10 seconds when the unit is
turned off.
– Excessive barking may indicate that the stimulation
intensity level is set too low.
* Before increasing the stimulation intensity level, check to see
that the collar has a proper t and both contact points are
touching your dog’s neck.

9
Testing theYS600
1. Turn the dial to “T”. The LED indicator will blink once every
4 seconds.
2. Use the cap end of a ballpoint pen and scratch between the
contact points. The unit is working properly when it vibrates
twice.
* The sensor is set to high sensitivity on test mode to activate
more easily. The test mode will only produce a non-
stimulating vibration.