Dogtra e-Fence User manual

OWNER’S MANUAL

2
CONTENTS

3
OVERVIEW
Thank you for purchasing our dogtra e-Fence System.
With dogtra e-Fence System your dog can freely play around within the boundaries you
have selected.
With the proper training you will enjoy seeing your dog in good demeanor.
MAIN FEATURES
•Collar/Receiver –Newly designed to make adjusting the collar strap easy.
•Waterproof Housing –The collar/receiver is waterproof.
•Wall transmitter features lightning/surge protection.
•Dogtra e-Fence has a warning/vibration signal before electrical stimulation/correction is
given to the dog.
•A wire indicator shows the continuity of fencing wires.
•Levels are easily adjusted using the intensity selection dial on the wall mount transmitter.
•Dogtra e-Fence is easy to install and use.

4
SAFETY
•Dogtra e-Fence collars use state-of-the-art microcomputer technology. The receiver has
an automatic control which limits the stimulus to eight seconds.
•Dogtra’s filtering system prevents reception from outside sources other than your
transmitter.
DOGTRA e-Fence System PACKAGE CONTENTS
•Wall-Mount Transmitter
•Collar/Receiver
•Battery Charger and Adapter
•Te s t L a m p
•Flags (boundary training flags)
•Underground Fence Wire (500 feet)
•Splicer
•Lightning/Surge Protective Wire
•Accessory Magnet
•Transmitter Mount Screws (2ea)
•Owner’s Manual

5
DESCRIPTION OF TRANSMITTER PARTS
dogtra e-Fence Transmitter
Adaptor Jack Connector
Wire Connectors
ON/OFF & Function
Selection Switch
Field Width
Adjustment Knob
Intensity Selection
Dial
ON/OFF Indicator Light
Wire Indicator Light

6
ON/OFF & Function Selection Switch
The On/Off Selection switch has three functions. When the toggle switch is up, the
warning/vibration followed by stimulation will occur. When this switch is down, only
stimulation occurs. When the switch is in the middle, the power is Off.
Pager/Stimulation
OFF
Stimulation

7
Field Width Adjustment Knob
This knob controls the width of the signal field (the distance from the boundary wire to the
location where the collar/receiver first activates). Turning the knob clockwise increases the
field width, giving your dog wider buffer area before the activation. Turning it
counterclockwise decreases the distance between the dog and fence before activation.
Intensity Selection Dial
The Intensity Selection Dial controls the stimulation level. Level 1 is the lowest setting and
level 5 is the highest. It is always best to start at level 1 and increase the levels until you
find a level where the dog reacts to the stimulation but does not overreact with excessive
vocalization.

8
ON/OFF Indicator Light
When the On/Off & Function Selection switch is either in the up or down position, the LED
light will be on, indicating that the power is on. When the switch is in the middle position,
the light goes off, indicating that the power is off.

9
Wire Indicator Light
When the wires are connected properly, the wire indicator light will be on. In the event the
e-Fence wire becomes damaged, the light will automatically turn off.

10
Wire Connectors
The easy-to-use push-release wire connectors let you instantly connect or disconnect the
boundary wire leads. Wires should be stripped about a half inch before being inserted into
the red connectors on the bottom of the wall mount transmitter.
Dogra e-Fence comes with lightning/surge protective wires. Insert the protective wires to
the black connector on the bottom of the wall transmitter.
Black Connector
(for the protective wires)

11
Adaptor Jack Connector
Plug the 110-volt adaptor into a 110-volt wall outlet and insert the adaptor plug into the
adaptor jack connector of the transmitter.
Adaptor Jack Connector

12
Wall-Mount Transmitter
Use the (2) included screws to mount the transmitter to a wall securely, near any standard
110-volt household outlet. The unit will withstand freezing temperatures, but it is not
waterproof. Therefore, we recommend mounting the transmitter in a safe, dry indoor area.
To power the wall transmitter, plug the AC adaptor into the standard 110-volt outlet and
connect it to the adaptor jack connector of the transmitter.

13
DESCRIPTION OF COLLAR PARTS
dogtra e-Fence Receiver
Collar strap
Battery Charging
Receptacle and Cover
ON/OFF Magnetic Switch
Indicator Light
Contact Point
110-volt

14
ON/OFF Magnetic Switch
To activate the Dogtra e-Fence, place the accessory magnetic switch (located on the top of
the wall mount transmitter) to the red dot on the collar/receiver. Hold them together for a
moment until the LED indicator light starts flashing on the receiver. The indicator light will
blink once every two seconds showing that the unit is charged and ready to use. (If the red
indicator light emits a double blink every two seconds, the batteries need to be charged.)
To deactivate the Dogtra e-Fence, place the accessory magnetic switch (located on the top
of the wall mount transmitter) to the red dot on the collar/receiver. The LED light will stop
blinking indicating that the unit is now off. To attain maximum battery life, deactivate the
unit when not in use.
Accessory Magnetic Switch

15
Receiver Indicator Light (LED)
Located on the front of the collar, the indicator light comes on and blinks once every two
seconds after the collar is turned on. The blinking will change from a single flash to a
double flash when the collar needs to be recharged.
The indicator light will come on when the dog reaches the edge of the signal field in the
yard.

16
Contact Points
The collar should be fitted so that the stainless steel contact points press firmly against the
dog’s skin. A loose fit can allow the collar to move around on the dog’s neck which may
cause irritation to the skin.
If the collar is too loose, electrical contact will be inconsistent and your corrections will be
inconsistent as well.

17
Collar/Receiver Battery Charging Receptacle
On the inside of the collar/receiver, next to the collar strap, is the battery charging
receptacle with a rubber cover plug.

18
Battery Charger
The battery charger is designed for a 110-volt wall outlet.
(European 220-volt AC charger is also available.)
110 volt charger

19
CHARGING THE BATTERIES
Dogtra uses Ni-MH (Nickel-Metal Hydride) batteries that do not have a memory. They can
be charged on a regular basis without harm. There is no need to completely drain the
batteries between charges.
1. Plug the 110-volt adaptor into a 110-volt wall outlet and insert the adaptor plug into
the battery charging receptacle of the receiver.
2. Charge the batteries for 14 hours before using the collar for the first time.
3. Do not charge the batteries near any flammable substances.
4. Fully charge the batteries for 14 hours if the collar is to be stored without use for a
period of a month or more.
5. Recharge the battery if :
- the indicator light on the collar is emitting a double blink every two seconds
- the indicator light on the receiver will not come on
- the indicator light on the receiver comes on momentarily but will not stay on
110-volt

20
TESTING YOUR DOGTRA e-Fence System
1. Activate the Dogtra e-Fence, place the accessory magnetic switch (located on the
top of the wall mount transmitter) to the red dot on the collar/receiver. Hold them
together for a moment until the LED indicator light starts flashing on the receiver.
The indicator light will blink once every two seconds showing that the unit is
charged and ready to use.
(If the red indicator light emits a double blink every two seconds, the batteries need
to be charged.)
2. Place the test light on the contact points on the receiver and hold it there.
3. The collar receiver should be held at the height of the dog’s neck with the contact
points pointed upward. Walk slowly toward the boundary wire. Be careful not to
touch the contact points.
4. Watch for the test light to come on.