Dometic OASIS ELITE 975 Series User manual

AWNINGS
DOOR AWNING
Form No. 3317402.000 03/20 | ©2020 Dometic Corporation
WARNING
Cancer and Reproductive Harm
www.P65Warnings.ca.gov
975XXXX.XX2(#)X
EN Oasis Elite 975 Series Automatic RV
Door Awning System
Installation & Operation Manual..........2

2EN
Contents Oasis Elite 975 Series
1 Explanation of Symbols and Safety
Instructions ............................ 2
1.1 Recognize Safety Information .............2
1.2 Understand Signal Words................2
1.3 Supplemental Directives .................3
1.4 General Safety Messages ................3
2 Intended Use ........................... 4
3 General Information ..................... 4
3.1 Included Hardware .....................4
3.2 Optional Components ..................4
3.3 Model Identification ....................4
4 Specifications .......................... 5
4.1 Door Clearance ........................5
4.2 Wire Length and Size....................5
4.3 Awning Dimensions ....................5
5 Pre-Installation ......................... 5
5.1 Installing the Door Roller and Edge Guard ..6
5.2 Determining the Awning Location .........6
5.3 Preparing the Awning Rail................7
6 Awning Installation...................... 7
6.1 Installing the Awning Rail and Inserting the
Awning...............................8
6.2 Making the Electrical Connections.........8
6.3 Completing the Installation...............9
7 Electrical Kit Installation................. 10
7.1 Connecting the Motor and Operating
Switch ..............................10
7.2 Installing the Ignition Interlock ...........10
7.3 Installing the LED Light Switch ...........10
7.4 Installing the LED Light Connections ...... 11
8 Post Installation.........................11
8.1 Testing the Operation .................. 11
8.2 Adjusting the Retraction and Extension .... 11
9 Awning Operation ..................... 12
9.1 Operating the Awning .................12
9.2 Closing the Awning Manually............12
10 Travel Storage and Removal ............. 13
10.1 Securing the Awning for Travel ...........13
10.2 Removing the Awning..................13
11 General Care and Maintenance........... 13
11.1 Cleaning the Hardware.................14
11.2 Cleaning the Fabric ....................14
11.3 Repairing a Pinhole in the Fabric..........14
12 Disposal .............................. 14
Limited One-Year Warranty ................. 15
Contents
Service Center & Dealer Locations
Visit: www.dometic.com
Read these instructions carefully. These instructions
MUST stay with this product.
1 Explanation of Symbols and
Safety Instructions
This manual has safety information and instructions to
help you eliminate or reduce the risk of accidents and
injuries.
1.1 Recognize Safety Information
This is the safety alert symbol. It is used to alert
you to potential physical injury hazards. Obey all
safety messages that follow this symbol to avoid
possible injury or death.
1.2 Understand Signal Words
A signal word identifies safety messages and property
damage messages, and also indicates the degree or
level of hazard seriousness.
DANGER!
Indicates a hazardous situation that, if not avoided,
will result in death or serious injury.

3
EN
Oasis Elite 975 Series Explanation of Symbols and Safety Instructions
WARNING
Indicates a hazardous situation that, if not avoided,
could result in death or serious injury.
CAUTION
Indicates a hazardous situation that, if not avoided,
could result in minor or moderate injury.
NOTICE: Used to address practices not related to
physical injury.
IIndicates additional information that is not related
to physical injury.
1.3 Supplemental Directives
To reduce the risk of accidents and injuries, please
observe the following directives before proceeding to
install or operate this appliance:
• Read and follow all safety information and
instructions.
• Read and understand these instructions before
installing or operating this product.
• The installation must comply with all applicable local
or national codes, including the latest edition of the
following standards:
U.S.A.
– ANSI/NFPA70, National Electrical Code (NEC)
– ANSI/NFPA 1192, Recreational Vehicles Code
Canada
– ANSI Z21.57, Recreational Vehicles Code
– CSA C22.1, Parts l & ll, Canadian Electrical Code
– CSA Z240 RV Series, Recreational Vehicles
1.4 General Safety Messages
WARNING: ELECTRICAL SHOCK, FIRE, AND/
OR EXPLOSION HAZARD. Failure to obey the
following warnings could result in death or
serious injury:
• This product must be installed or serviced by a
qualified service technician.
• Do not modify this product in any way. Modification
can be extremely hazardous.
• Frequently examine the product for an imbalance
(uneven fit, sagging, or loose parts), signs of wear or
damage to the wiring (if applicable), and other critical
parts, such as the awning fabric, cables, and arm
assemblies. Do not use the product if adjustments or
repairs are necessary.
• Disconnect the product from the power supply (if
applicable), and do not operate the product when
maintenance (such as window cleaning) is being
carried out in the vicinity.
• Do not allow anyone (including children) with
reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, to use this
product, unless they have been given supervision or
instruction (concerning the use of this product) by a
person responsible for their safety.
• Do not allow children to play with the product or
with the operating switch.
• Keep remote controls (if applicable) away from
children.
WARNING: IMPACT, CRUSH, OR FIRE
HAZARD. Failure to obey the following
warnings could result in death or serious
injury:
• Never leave an open awning unattended. Keep
the awning stowed (closed) when snow, heavy rain,
wind, and severe weather conditions are expected.
• Do not allow water to pool, snow to accumulate,
or heavy debris to rest on the awning fabric. Do not
hang or place anything on the awning. The awning
will become unstable, and it could bend or collapse.
• Keep sources of heat and fire (barbecue grills,
portable heater, etc.) away from the awning.
CAUTION: PINCH HAZARD.
Maintain a horizontal distance of at least 16 in.
(41cm) between the fully open awning and any
permanent object. Failure to obey this caution
could result in minor or moderate injury.
NOTICE: Do not face the awning toward permanent
objects that may interfere with the awning operation.

4EN
Intended Use Oasis Elite 975 Series
2 Intended Use
These instructions apply to the Oasis Elite 975 series
awning (hereinaer referred to as “door awning”,
“awning,” or “product”). It is designed for use over RV
entry doors. This awning can be installed by one person
with brief help from additional personnel. Use these
instructions to ensure correct installation, function, and
operation of the product.
The manufacturer accepts no liability for damage in the
following cases:
• Faulty assembly or connection
• Damage to the product resulting from mechanical
influences and excess voltage
• Alterations to the product without express permission
from the manufacturer
• Use for purposes other than those described in the
operating manual
Dometic Corporation reserves the right to modify
appearances and specifications without notice.
3 General Information
This section describes the included hardware, optional
kits and components, and the model identification
number.
3.1 Included Hardware
IThe images used in this document are for reference
purposes only. Components and component
locations may vary according to specific product
models. Measurements may vary ±0.38 in. (1cm).
Included Hardware Quantity
#10-16 X 5/8 in. Self-Drilling Screws 2
#6-20 X 1/2 in. Square Drive Screw14
1Quantity varies by length of the awning rail.
3.2 Optional Components
Optional Components and Kits Ref. Number
Door Roller Kit 830304
Door Roller Kits (50 Pack) 830304.003
WeatherPro Control 3310287.002
WeatherPro Control 3310287.010
Power Awning Pro Control 3317115.000
Control Switch Accessory 3310455.062
Ignition Interlock Kit 3313283.008
Vinyl Liquid Patch (VLP) 3314216.000
3.3 Model Identification
Each awning is manufactured with a data plate that
includes useful information like the model number, fabric
color and type, awning rail, paint code, and LED. The
data plate is located on the back of the lead rail on the
front cover.
This section explains the parts of the model identification
number.
975 XX XX . X X (#) X
LED
Paint Code
Awning Rail
Fabric Code
Size
Fabric Color
Series Number
Series Number 975 = Elite 975 series awnings
Fabric Color Variable
Size Code
48 = 48 in. (122 cm)
56 = 56 in. (142 cm)
60 = 60 in. (152 cm)
Fabric 0 = Vinyl
1 = Acrylic
Awning Rail 0 = Without awning rail
1 = With awning rail
Paint Code Variable
LED (blank) = Without LED
L = With LED

5
EN
Oasis Elite 975 Series Pre-Installation
4 Specifications
This section describes the components of the awning,
including size, dimensions, and placement.
4.1 Door Clearance
q
w
e
1 Door Clearance
qAwning Rail eMinimum Clearance
10.5 in. (26.7 cm)
wRV Door (Open)
Maintain a minimum distance of 10.5 in. (26.7 cm)
between the awning rail and the entry door.
4.2 Wire Length and Size
To avoid voltage drop, follow this wire length guide for
all awning wiring.
Wire Length Wire Size
10  (3 m) and Under 14 gauge
11  – 30  (3.4 m – 91.4 m) 12 gauge
Over 30  (91.4 m) 10 gauge
4.3 Awning Dimensions
q
w
e
(Front)
(Side)
2 Overall Awning Dimensions
Model q(L) w(H) e(D)
975XX48.XX2(#)(L) 48.5 in.
( 123 cm)
6 in.
(15cm)
4 in.
(10cm)
975XX56.XX2(#)(L) 55.5 in.
(141 cm)
6 in.
(15cm)
4 in.
(10cm)
975XX60.XX2(#)(L) 59.5 in.
(151cm)
6 in.
(15cm)
4 in.
(10cm)
5 Pre-Installation
WARNING: IMPACT OR CRUSH HAZARD.
Make sure the mounting surface on the RV is flat,
has solid structural backing where the fasteners
penetrate surface, and will safely and securely
support the product. Otherwise, the product may
become unstable and could detach, bend, or
collapse. Failure to obey this warning could result in
death or serious injury.
NOTICE: Failure to obey the following notices may
cause damage to the product:
• Make sure the awning rail is parallel to the RV floor
and is not warped or curved before installing the
awning fabric. If the awning rail is not straight, the
awning fabric may wrinkle or stretch.

6EN
Pre-Installation Oasis Elite 975 Series
• Allow for sufficient clearance between the awning
fabric and the entry door to accommodate the
awning slope.
• Do not allow the corner of the entry door to contact
the awning fabric. Otherwise, premature wear or
tearing of the awning fabric could occur.
5.1 Installing the Door Roller and
Edge Guard
Squared-corner entry doors and some rounded-corner
doors may contact the awning fabric and cause damage.
To prevent damage, you must install a door roller kit (not
included). See “Optional Components” on page4
to order door roller kits.
IIf the awning does not need a door roller, skip this
section and proceed to “Determining the Awning
Location” on page6.
q
w
e
r
3 Roller Clearance
qAbove Door
Clearance
0.3–0.4 in.
(0.8–1.0 cm)
wSelf-drilling Screws
eDoor Roller
rOuter Entry Door
1. Place the door roller at the upper corner opposite to
the hinge of the outer entry door.
2. Face the roller out and 0.3–0.4 in. (0.8–1.0 cm) above
the door.
3. Place and tighten the self-drilling screws (provided)
through the mounting holes and into the door.
q
w
4 Installing the Door Edge Guard
qDoor Edge Guard wInner Screen Door
4. Clip the door edge guard onto the upper corner
(opposite to the hinge) of the inner screen door.
IA slight “travel line” may appear where the door
roller contacts the awning fabric. This is normal and
does not affect the integrity of the awning fabric.
5.2 Determining the Awning Location
IIf your Oasis 975 model did not include the awning
rail, you may order it separately (see “Optional
Components” on page4), or you may use an
awning rail from a previous Oasis awning if the rail is
not damaged.
5 Awning Location

7
EN
Oasis Elite 975 Series Pre-Installation
To ensure the correct function and appearance, the
awning rail should be installed on a flat, straight surface.
In addition, the location should:
• Be a solid structure that will support the awning rail
and the back rail at all mounting points.
• Be parallel to the RV floor.
• Be centered over the door.
• Not interfere with the entry door swing when
the awning is completely extended. See “Door
Clearance” on page5.
• Provide a minimum space of 0.5 in. (1.3 cm) at the top
and sides of the awning case. Additional clearance is
recommended to allow easier access for servicing.
5.3 Preparing the Awning Rail
q w
6 Preparing the Awning Rail
qLED Awning
(Top Only)
wTypical Awning
(Top and Bottom)
1. Select the desired awning rail end on the RV into
which you will insert the awning fabric.
2. Use a flat-bladed screwdriver to flare (widen) that end
of rail, and file any sharp edges.
6 Awning Installation
WARNING: IMPACT OR CRUSH HAZARD.
This product should be installed in a controlled
environment (inside). Do not install the product
during windy conditions or when wind is expected.
The product could move unpredictably or become
unstable, causing it to detach, bend, or collapse.
Failure to obey this warning could result in death or
serious injury.
WARNING: FIRE OR ELECTRICAL SHOCK
HAZARD.
Before drilling or cutting into the RV, make sure
there are no obstacles (such as wires, pipes, etc.)
inside the RV’s roof, floor, or walls. Shut off the gas
supply, disconnect the 120 VAC power from the
RV, and disconnect the positive (+) 12 VDC terminal
from the supply battery. Failure to obey this warning
could result in death or serious injury.
CAUTION: LIFTING HAZARD.
Use proper liing technique and control when
liing the product. Failure to obey this caution
could result in minor to moderate injury.
NOTICE: Failure to obey the following notices may
cause damage to the product:
• Always seal the wiring against weather and moisture
where the wiring and fasteners enter the RV’s walls,
roof, or floor. Always use sealant on clean parts and
surfaces . Otherwise, water leakage could occur.
• Do not pinch the wiring or allow it to rub against
sharp edges. If wiring is damaged, it must be
replaced by a qualified service technician.

8EN
Pre-Installation Oasis Elite 975 Series
6.1 Installing the Awning Rail and
Inserting the Awning
q
e
w
7 Installing the Awning
qAwning Rail eAwning Back Rail
Bracket
wAwning Back Rail
1. Apply sealant to the back edge of the awning rail and
to the #6-20 X 1/2 in. screws (provided).
2. Place and tighten the screws through the awning rail
and into the RV wall.
3. Carefully li the awning and align the back rail bracket
to the prepared awning rail end. Use a stepladder if
necessary.
4. Insert the back rail bracket into the awning rail.
5. Carefully slide the awning until it is in the desired
position.
To facilitate sliding along the rail, you may rotate the
awning up and secure the motor wiring out of the
way.
6.2 Making the Electrical
Connections
t
w
e
r
8 Awning Wiring Hole Location
qWiring Hole rBottom Edge to Wiring
Hole: 3.6 in. (9.1cm)
wLe-Hand (LH) Cover
eAwning Back Rail tLH Cover to Wiring
Hole: 0.7 in. (1.8 cm)
1. Mark the awning wiring hole location. With the
awning in the desired position:
a. Make a vertical mark along the LH edge of the
awning back rail.
b. Make a horizontal mark along the bottom edge of
the awning back rail.
c. Carefully slide the awning along the awning rail to
the right, far enough for free access to the marked
location.
d. Measure 3.6 in. (9.1 cm) above the horizontal
mark, and make a new horizontal mark.
e. Measure 0.7 in. (1.8 cm) to the le of the vertical
mark, and make a new vertical mark that crosses
the second horizontal mark.

9
EN
Oasis Elite 975 Series Pre-Installation
2. Using the plug connectors supplied with the wiring
harness and the electronic control kit, make sure the
connections will mate:
– BLACK wire to BLUE awning motor wire
– RED wire to BROWN awning motor wire
3. Drill one 5/8 in. (1.6 cm) diameter hole at the marked
wiring hole location through the RV’s outside wall.
e
w
q
9 Awning Wiring
qLH Cover eAwning Motor
Wiring
wDoor Motor Wiring
Harness
4. Pull the wiring through the drilled hole, the grommet
(installer supplied), and the wiring hole in the LH
cover.
IIf using sealant or heat shrink tubing instead of a
grommet, make sure the sealant or tubing will
provide effective and permanent protection against
wire damage.
5. Add the plug connector to the door motor wiring
harness in compliance with all applicable codes
6. Connect the plug connector to the awning motor
wiring.
6.3 Completing the Installation
1. Carefully slide the awning to the le along the awning
rail until the LH cover align with the first vertical mark.
2. With power applied to the awning, fully extend the
awning.
3. Verify the wiring (if applicable) is not caught between
the awning and the RV wall before tightening the
back rail fasteners.
q q
w
e.e
.
10 Bottom Mounting Holes
qApproximate Location of Bottom Mounting Holes
wDistance above Bottom Edge: 0.5 in. (1.3 cm)
eDistance from End of Back Rail: 4 in. (10 cm)
4. If the bottom mounting holes are not already present,
drill two 9/16 in. (4 mm) diameter holes through the
back rail approximately:
– 0.5 in. (1.3cm) above the bottom edge
– 4 in. (10 cm) from each end of the back rail
5. Apply sealant to the #10-16 X 5/8 in. screws
(provided).
IThe screws provided are self drilling (tapping), so it
is not necessary to drill through the RV wall.
q
w
e
r
11 TEK Screw Location
qTEK Screw eAwning Bracket
wAwning Rail rFrom Bracket Edge
6 in. (15 cm)

10 EN
Electrical Kit Installation Oasis Elite 975 Series
6. Place and tighten the screws through the bottom
mounting holes into the RV.
7. Secure the awning with a #6 X 1/2 in. TEK screw
(installer supplied) on each end of the awning rail,
approximately 6 in. (15 cm) from the awning bracket
edge.
7 Electrical Kit Installation
This section describes how to install electrical
components such as the motor and operating switch,
the LED light switch, and the ignition interlock.
WARNING: IMPACT, CRUSH, OR PROJECTILE
HAZARD. Failure to obey these warnings
could result in death or serious injury:
• Make sure the ignition interlock is working correctly
before traveling with the RV. If the awning responds
to the switch with the ignition in the ON position,
accidental operation during transit could occur.
The awning must be disabled, then serviced by a
qualified technician.
• Do not attempt transport with an awning motor that
has been damaged from an impact. Otherwise, the
awning could extend quickly and unexpectedly,
becoming a projectile during transit. If the awning
has been damaged, contact a licensed or certified
technician for repair.
WARNING: FIRE OR ELECTRICAL SHOCK
HAZARD. Failure to obey these warnings
could result in death or serious injury:
Before drilling or cutting into RV, make sure there
are no obstacles (wires, pipes, etc.) inside the
RV’s roof, floor, or walls. Turn off the gas supply,
disconnect the 120 VAC power from the RV, and
disconnect the positive (+) 12 VDC terminal from
the supply battery.
NOTICE: Failure to obey the following notices may
cause damage to the product:
• Always seal the wiring against weather and
moisture where it enters the RV’s walls, roof, or floor.
Otherwise, water leakage could occur.
• Use a grommet or heat shrink tubing wherever wiring
passes through the RV wall.
• Do not pinch the wiring or allow it to rub against
sharp edges. If the wiring is damaged, it must be
replaced by a qualified service technician.
• Do not expose the LED switch to weather, extreme
temperatures, or long hours in direct sunlight.
7.1 Connecting the Motor and
Operating Switch
1. Pull the motor wiring through the wiring hole and
grommet, and connect it to the appropriate wiring
inside the RV.
2. Make the electrical connections inside the RV per
the instructions supplied with your Dometic Control
Switch Accessory.
7.2 Installing the Ignition Interlock
1. Install the ignition interlock per the instructions
supplied with the ignition interlock kit or an optional
control kit such as Power Awning Pro or WeatherPro.
2. Verify the ignition interlock is working correctly:
a. Turn the ignition to the ON position.
b. Attempt to operate the awning.
If the awning does not respond, the ignition interlock is
operating properly.
If the awning operates:
1. Close the awning.
2. Disconnect the awning from the power source.
3. Have the ignition interlock repaired by a qualified
service technician.
7.3 Installing the LED Light Switch
An LED light switch (installer supplied) is required for
awning models equipped with an LED light strip.
IIf the awning does not have an LED light strip, skip
this section and proceed to “Post Installation” on
page11.
1. Find a suitable location for the LED switch.
2. Inside the RV, route the wiring to the general location

11
EN
Oasis Elite 975 Series Post Installation
where connections to the awning hardware will be
made.
3. Make the appropriate wiring connections inside the
RV per the instructions supplied with the LED light
switch.
Wiring connections to the awning through the outside
RV wall will be made later.
7.4 Installing the LED Light
Connections
IIf the awning does not have an LED light strip, skip
this section and proceed to “Post Installation” on
page11.
1. With the awning open, drill one 5/8 in. (1.6 cm)
diameter hole through the outside RV wall that is:
– Near the right end of the awning.
– Under the awning rail.
– Where the LED wiring can pass through wall
without interference.
2. Pull the wiring through the wiring hole and the
grommet.
3. Connect the LED switch wiring to the factory pre-
wired LED light strip per the instructions supplied
with your LED switch kit (installer supplied).
4. Secure the wiring to prevent pinching or other
damage during awning operation. Allow enough
slack in the wiring to safely accommodate possible
fabric movement.
8 Post Installation
This section describes the tasks you need to do aer
completing the installation.
8.1 Testing the Operation
With power applied to the awning, open and close the
awning to verify that all parts are functioning correctly.
See “Awning Operation” on page12.
8.2 Adjusting the Retraction and
Extension
The awning comes equipped with limit switches to stop
the motor at full extension and full retraction. These
limits are set at the factory and typically should not need
any adjustment by the installer or the user. If the limit
switches need to be adjusted, use a 3 mm hex key.
w
q
12 Limit Switches (Bottom, Le End)
qExtension
Adjustment Screw
wRetraction
Adjustment Screw
Retraction adjustments:
• If the front rail does not fit snugly against the case
when the awning is fully closed, turn the retraction
adjustment screw clockwise to adjust for more
retraction.
• If the motor does not turn itself off and continues
trying to turn when the awning is fully closed, turn
the retraction adjustment screw counterclockwise to
adjust for less retraction.
IIf the motor continues to try to turn when the
awning is fully retracted, damage to the motor or
the awning components may occur.
Extension adjustments:
• If the awning tries to overextend, turn the extension
adjustment screw counterclockwise to adjust for less
extension.
• If the awning does not fully extend, turn the extension
adjustment screw clockwise to adjust for more
extension.

12 EN
Awning Operation Oasis Elite 975 Series
9 Awning Operation
WARNING: IMPACT OR CRUSH HAZARD.
Do not allow water or snow to accumulate on the
awning fabric. This weight will cause the awning to
become unstable, and it could bend or collapse.
Failure to obey this warning could result in death or
serious injury.
WARNING: PINCH HAZARD.
Keep clear of the arm assemblies while closing the
awning. The arm assemblies fold or close against
the back rail. Failure to obey this warning could
result in death or serious injury.
WARNING: ELECTRICAL SHOCK HAZARD.
Disconnect the power from the product before
accessing the wiring connections. There may
be issues mimicking a power failure with electric
current still present, or power may return
unexpectedly. Failure to obey this warning could
result in death or serious injury.
NOTICE: When using an external power source to close
the awning, disconnect the power immediately aer
the awning retracts. Otherwise, damage to the awning
motor could occur.
9.1 Operating the Awning
IN
OUT
q w e
13 Power Switch
qRetract eExtend
wStop
To operate the awning, use the switch as shown in
Figure 13, or use the instructions supplied with the
optional control kit.
The awning automatically stops when the button is
released.
9.2 Closing the Awning Manually
In case of a power failure, you may need to close the
awning manually using power from an external source,
such as a 12VDC automobile battery.
Aer the awning is closed manually, it may require
service by a qualified service technician.
1. Rule out simple causes for power failure, such as:
– RV is not connected to power
– Battery is low or discharged
– Ignition interlock is on
2. Disconnect the 120 VDC power from the RV to the
awning.
3. Unplug the door motor wiring harness connector
from the electronic control box.
IDo not connect to the electronic control box.
Match the wire lead colors to the door motor wiring
harness colors.
– BLACK wire lead to BLUE door motor wire
– RED wire lead to BROWN door motor wire
4. Connect 16-gauge (minimum) wire leads (user
supplied) to the door motor wiring harness
connector, and tape the wires in place with electrical
tape.
5. With someone watching the awning, connect the
other end of the wire leads to the 12 VDC external
power source until the awning retracts to its closed
position:
IThe lead wire connected to the positive (+) terminal
must have a (3 A) in-line fuse installed.
IThe awning will extend if wire leads are reversed.
a. Connect the BLACK wire to the positive (+)
terminal.
b. Connect the RED wire to negative (-) terminal.
c. Disconnect the wire leads from power source
once the awning fully retracts.

13
EN
Oasis Elite 975 Series Travel Storage and Removal
6. If the awning responds to the external power source,
make sure the awning is completely closed and
secure. See “Securing the Awning for Travel” on
page13.
7. If the awning does not respond to the external power
source, the wiring harness may have a short. Proceed
to the next step.
8. Remove the LH cover from the awning, and unplug
the door motor wiring harness from the awning
motor wiring connector. See Figure 9.
9. Connect 16-gauge minimum wire leads (user
supplied) to the awning motor wiring connector, and
secure in place with electrical tape.
IDo not connect to the door motor wiring harness.
Match wire lead colors to the awning motor wiring
colors:
– BLACK wire to BLUE awning motor wire
– RED wire to RED (or BROWN) awning motor wire
10.Repeat steps 5 through 6.
11. If the awning still does not respond to the external
power source, the motor may be defective. Proceed
to “General Care and Maintenance” on page13.
10 Travel Storage and Removal
WARNING: IMPACT OR PINCH HAZARD.
Hold the awning rail firmly while closing the
awning. The awning rail and lateral arm assemblies
are under tension from the gas strut and could
extend quickly and unexpectedly if not controlled.
Failure to obey this warning could result in death or
serious injury.
CAUTION: LIFTING HAZARD.
Use proper liing technique and control when
liing the product. Failure to obey this caution
could result in minor to moderate injury.
10.1 Securing the Awning for Travel
1. Fully close the awning.
2. Verify the awning is secure for traveling.
10.2 Removing the Awning
1. Fully close the awning.
2. With the LH cover removed from the awning, verify
the door motor wiring harness is unplugged from the
awning motor wiring connector. See Figure 9.
3. Remove the two #10-16 X 5/8” screws securing the
awning back rail to the RV. See Figure 10.
4. Remove the #6 X 1/2” TEK screws securing the
awning bracket to the awning rail. See Figure 11.
5. With brief help from additional personnel, carefully
slide the awning from the rail.
6. While maintaining firm control, push the lead rail
back until it closes against the awning casing. Then
securely tie it closed with fabric strapping, light rope,
or several wraps of strong duct tape.
11 General Care and
Maintenance
This section describes basic usage precautions, cleaning
the hardware and fabric, and repairing pinholes in the
fabric.
NOTICE: Failure to obey the following notices could
damage the product.
• Do not use strong chemicals or abrasives to clean
parts, as their protective surfaces will be damaged.
• Do not use abrasive or corrosive cleaners, mildew
removers, or hard bristle brushes on the awning
fabric.
• Do not use silicone sprays near labels. Otherwise,
the label’s adhesive bond to the product surfaces
could weaken.
• Do not use insecticides or other sprays near the
awning fabric. These could cause stains and could
adversely affect the fabric’s ability to repel water.
• Do not expose the awning to adverse environmental
conditions, corrosive agents, or other harmful
conditions.
• Do not allow the corner of the entry door to contact
the awning fabric. Otherwise, premature wear or
tearing of the awning fabric could occur.

14 EN
Disposal Oasis Elite 975 Series
• Do not allow dirt, leaves, or other debris to
accumulate on the awning, which could cause
abrasion and stains. Mildew could grow on the dirt
and organic debris, causing permanent discoloration,
stains, and odors to the awning fabric.
• Never close the awning for storage when wet. The
combination of moisture and dirt could result in
mildew, discoloration, and stains.
IIf it is necessary to close the awning temporarily
while it is wet, make sure you open it and let it dry
as soon as conditions allow before closing it again.
11.1 Cleaning the Hardware
• Clean the awning hardware as needed with a mild
surface cleaner, such as dish soap.
• Apply silicone spray lubricant as needed to keep the
fabric roller tube assembly’s moving parts operating
smoothly.
• Lubricate all sliding surfaces of the arm assemblies
with silicone spray as needed.
11.2 Cleaning the Fabric
Vinyl fabric offers the advantage of durability and water
resistance.
IWrinkling is a normal characteristic of vinyl.
Wrinkling may be more noticeable when retracted,
and aer prolonged periods of being rolled up
and stored. Leave the awning open during warm
weather to minimize the wrinkling.
1. Mix 0.25 cup (59 ml) dish soap and 0.25 cup (59ml)
bleach to 5 gallons (19L) of fresh water to use as a
cleaning solution.
2. Liberally drench the open the awning fabric with
cleaning solution.
3. Close the awning.
4. Let it soak for 5 minutes.
5. Open the awning.
6. Thoroughly rinse the awning to remove the solution,
repeating as oen as needed to be sure you have
removed the solution completely.
IBleach will degrade the awning fabric if it is not
completely removed.
7. Allow the awning to dry thoroughly before rolling up
and stowing.
11.3 Repairing a Pinhole in the
Fabric
NOTICE: Never close the awning when the Vinyl Liquid
Patch (VLP) patch is wet. Otherwise, the VLP will melt
through the layers, causing damage to other parts of the
awning fabric.
You can also use this procedure to repair patches where
coating has flaked off the top layer of the vinyl fabric:
1. Apply a very small dab of VLP on the tip of a cotton
swab.
2. Gently roll the cotton swab around the pinhole. The
VLP melts the coating on the fabric, which quickly fills
in the pinhole and blends with all colored vinyls.
3. Allow the VLP to dry thoroughly before rolling up and
stowing the awning.
12 Disposal
MPlace the packaging material in the appropriate
recycling waste bins, whenever possible. Consult
a local recycling center or specialist dealer for
details about how to dispose of the product in
accordance with all applicable national and local
regulations.

15
EN
Oasis Elite 975 Series Disposal
LIMITED ONE-YEAR
WARRANTY
LIMITED ONE-YEAR WARRANTY AVAILABLE AT WWW.
DOMETIC.COM/WARRANTY.
IF YOU HAVE QUESTIONS, OR TO OBTAIN A COPY
OF THE LIMITED WARRANTY FREE OF CHARGE,
CONTACT:
DOMETIC CORPORATION
CUSTOMER SUPPORT CENTER
1120 NORTH MAIN STREET
ELKHART, INDIANA, USA 46514
1-800-544-4881 OPT 1

Mobile living made easy.
dometic.com
YOUR LOCAL
DEALER
dometic.com/dealer
YOUR LOCAL
SUPPORT
dometic.com/contact
YOUR LOCAL
SALES OFFICE
dometic.com/sales-offices