Dometic Brisk II User manual

CLIMATE CONTROL
AIR CONDITIONERS
WARNING
Cancer and Reproductive Harm
www.P65Warnings.ca.gov Form No. 4445104227 3317817.000 2023-10-31
Brisk II (B57915, B59516, B79516), High Performance (540315, 540316),
Blizzard NXT (H540315, H540316), FreshJet (FJX3473, FJX3573)
EN Rooop Air Conditioner (Air
Distribution Box, Mechanical Controls)
Installation and operation manual . ........2

2EN
Rooop Air Conditioner (Air Distribution Box, Mechanical Controls)
Copyright
© 2023 Dometic Group. The visual appearance of the contents of this manual is protected by copyright and design law.
The underlying technical design and the products contained herein may be protected by design, patent or be patent
pending. The trademarks mentioned in this manual belong to Dometic Sweden AB. All rights are reserved.

Placing the rooop model unit Contents
1 Related documents...................... 3
2 Explanation of symbols and safety
instructions ............................ 4
2.1 Recognize safety information .............4
2.2 Understand Signal words ................4
2.3 Supplemental directives .................4
2.4 General safety messages. . . . . . . . . . . . . . . . . 4
3 Intended use ........................... 5
4 General information ..................... 5
4.1 Tools and materials .....................5
4.2 Model identification ....................5
4.3 ADB components ......................6
4.4 Rooftop component dimensions by model ..6
4.5 Placement requirements .................9
5 Specifications ......................... 10
6 Wiring diagrams ........................11
7 Pre-installation .........................11
7.1 Determining your cooling needs .........12
7.2 Preparing the RV roof opening ...........12
7.3 Routing the wiring .....................13
7.4 Positioning the rooftop component.......14
7.5 Preparing to work inside the RV ..........14
8 Installation ............................ 15
8.1 Installing the foam dividers ..............15
8.2 Securing the unit ......................18
8.3 Wiring the unit to the power supply.......19
8.4 Connecting the power supply ...........19
8.5 Finalizing the installation ................20
9 Operation............................. 20
9.1 Understanding the controls .............21
9.2 Understanding the settings..............21
10 Troubleshooting .......................22
11 Maintenance .......................... 23
11.1 Cleaning the air filter ...................23
11.2 Cleaning the ADB housing ..............23
12 Disposal .............................. 23
Limited One-Year Warranty .................23
Contents
Service center & dealer locations
Visit: www.dometic.com
Please read these instructions carefully and follow all instructions,
guidelines, and warnings included in this product manual in order to
ensure that you install, use, and maintain the product properly at all
times. These instructions MUST stay with this product.
By using the product, you hereby confirm that you have read
all instructions, guidelines, and warnings carefully and that you
understand and agree to abide by the terms and conditions as set
forth herein. You agree to use this product only for the intended
purpose and application and in accordance with the instructions,
guidelines, and warnings as set forth in this product manual as well
as in accordance with all applicable laws and regulations. A failure
to read and follow the instructions and warnings set forth herein may
result in an injury to yourself and others, damage to your product,
or damage to other property in the vicinity. This product manual,
including the instructions, guidelines, and warnings, and related
documentation, may be subject to changes and updates. For up-to-
date product information, please visit www.dometic.com.
3
EN
1 Related documents
Find the installation manual on-line in
French at
http://qr.dometic.com/beGoyi
Find the installation manual on-line in
Spanish at
http://qr.dometic.com/beGp0U

4EN
Explanation of symbols and safety instructions Rooop Air Conditioner (Air Distribution Box, Mechanical Controls)
2 Explanation of symbols and
safety instructions
This manual has safety information and instructions to
help you eliminate or reduce the risk of accidents and
injuries.
2.1 Recognize safety information
This is the safety alert symbol. It is used to alert
you to potential physical injury hazards. Obey all
safety messages that follow this symbol to avoid
possible injury or death.
2.2 Understand Signal words
A signal word will identify safety messages and property
damage messages, and also will indicate the degree or
level of hazard seriousness.
DANGER!
Indicates a hazardous situation that, if not avoided,
will result in death or serious injury.
WARNING
Indicates a hazardous situation that, if not avoided,
could result in death or serious injury.
CAUTION
Indicates a hazardous situation that, if not avoided,
could result in minor or moderate injury.
NOTICE: Used to address practices not related to
physical injury.
IIndicates additional information that is not related
to physical injury.
2.3 Supplemental directives
To reduce the risk of accidents and injuries, please
observe the following directives before proceeding to
install, operate, or service this product:
• Read and follow all safety information and
instructions.
• Read and understand these instructions before
installing, operating, or servicing this product.
• The installation must comply with all applicable local
or national codes, including the latest edition of the
following standards:
U.S.A.
– ANSI/NFPA70, National Electrical Code (NEC)
– ANSI/NFPA 1192, Recreational Vehicles Code
– ANSI Z21.57, Recreational Vehicles Code
Canada
– CSA C22.1, Parts l & ll, Canadian Electrical Code
– CSA Z240 RV Series, Recreational Vehicles
2.4 General safety messages
WARNING: ELECTRICAL SHOCK, FIRE, AND/
OR EXPLOSION HAZARD. Failure to obey the
following warnings could result in death or
serious injury:
• Use only Dometic replacement parts and
components that are specifically approved for use
with the product.
• Avoid improper installation, adjustment, alterations,
service, or maintenance of the product. Installation,
service, and maintenance must be done by a
qualified service person only.
• Do not modify this product in any way. Modification
can be extremely hazardous.
• Use care when diagnosing and/or adjusting
components on a powered product.
• This product is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the product by a
person responsible for their safety.
• Children should be supervised to ensure that they do
not play with the product.

5
EN
Rooop Air Conditioner (Air Distribution Box, Mechanical Controls) Intended use
3 Intended use
The Rooop Air Conditioner (Air Distribution Box,
Mechanical Controls), also referred to as the “product”
or “unit”, is designed and intended for installation
on the roof and interior of a Recreational Vehicle
(RV) during or aer the time it is manufactured. The
product is comprised of two main components: the
rooop component and the internal air distribution box
(ADB) component.
This product can be installed by one person with brief
help from additional personnel. Use these instructions
to ensure a properly installed, and properly functioning
product.
The manufacturer accepts no liability for damage in the
following cases:
• Faulty assembly or connection
• Damage to the product resulting from mechanical
influences and excess voltage
• Alterations to the product without express permission
from the manufacturer
• Use for purposes other than those described in the
operating manual
Dometic Corporation reserves the right to modify
appearances and specifications without notice.
4 General information
This section provides general information about the unit
and its components.
IThe images used in this document are for reference
purposes only. Components and component
locations may vary according to specific product
models. Measurements may vary ±0.38 in. (10 mm).
4.1 Tools and materials
Dometic recommends that the following tools and
materials be used.
Recommended tools and materials
Framing Wood All-Weather Caulk
Knife/Box Cutter Screwdrivers
Electrical Connectors 3/8” Torque Wrench Socket
Basic Electrical Connection
Tools
Torque Wrench1(40 in lbs)
1Models FJX3473 and FJX3573 require a Torque Wrench (22.2 in lbs).
Optional parts1
FreshJet Air Distribution Box
Spacer Kit
9620006638
1 Available as an accessory (not included). Accommodates a roof thickness
greater than 5.5 in. (140 mm) and includes two spare 1.2 in. (30mm) foam
dividers and four 9-1/2 in. long bolts.
4.2 Model identification
The model identification labels are located as follows:
• The rooop component and serial numbers are found
on the identification label located on the bottom of
the base pan. To view the identification label, remove
the return air vent grille from the ADB.
• The ADB component model and serial numbers
are found on the rating plate located on the ceiling
template. To view the rating plate, look through the
filter opening.
IHave this information ready before contacting
Dometic for service.

6EN
General information Rooop Air Conditioner (Air Distribution Box, Mechanical Controls)
4.3 ADB components
This section identifies the main ADB components.
q
w
t
r
e
1 ADB components
qFoam Dividers rADB Cover
wCeiling Template tLong Bolts
eControl Box
4.4 Rooop component dimensions
by model
This section provides the external dimensions and
clearance measurements of the rooop component.
4.4.1 FreshJet
qq
yyt
r
uuii
wwee
2 FreshJet (FJX3473, FJX3573)
q14.4 in. (366 mm) tAir Flow Clearance
Area (Shaded)
w29.6 in. (753 mm)
e27.6 in. (702 mm) yCenter Line of Unit
r18.0 in. (457 mm)
Clearance
uRoof Opening
iFront of Unit

7
EN
Rooop Air Conditioner (Air Distribution Box, Mechanical Controls) General information
4.4.2 Brisk II
qq
rr
i
u
ttyy
ww
ee
3 Brisk II (B57915,B59516, B79516)
q13.7 in. (349 mm) yFront of Unit
w29.6 in. (751 mm) u18 in. (457 mm)
Clearance
e27.6 in.(701 mm)
rCenter Line of Unit iAir Flow Clearance
Area (Shaded)
tRoof Opening
4.4.3 Blizzard NXT
qq
rr
iu
o
u
tt
yy
wwee
4 Blizzard NXT (H540315, H540316)
q13.9 in. (353 mm) u4.0 in. (102 mm)
Clearance
w40.0 in. (1016 mm)
e30.0 in. (762 mm) i18.0 in. (457 mm)
Clearance
rCenter Line of Unit
tRoof Opening oAir Flow Clearance
Area (Shaded)
yFront of Unit

8EN
General information Rooop Air Conditioner (Air Distribution Box, Mechanical Controls)
4.4.4 High Performance
qq
rr
i
u
ttyy
ww
ee
5 High Performance (540315, 540316)
q13.0 in. (330 mm) yFront of Unit
w39.6 in. (1006 mm) u18.0 in. (457 mm)
Clearance
e29.9 in. (760 mm)
rCenter Line of Unit iAir Flow
Clearance Area
(Shaded)
tRoof Opening
4.4.5 ADB component dimensions
This section provides the internal dimensions of the ADB
component.
q
t
y
w
rr
ee
rr
uu
ii
ii
ooaa
uu
6 Dimension measurements
qFront of Unit yCenter Line of Unit
w2.3 in. (59 mm) u11.6 in. (295 mm)
e23.0 in. (583 mm) i3.4 in. (86 mm)
r20.4 in. (518 mm) o6.0 in. (152 mm)
tRoof Opening a3.0 in. (76 mm)

9
EN
Rooop Air Conditioner (Air Distribution Box, Mechanical Controls) General information
4.5 Placement requirements
The rooop component is specifically designed for
installation on the roof of an RV. To determine where to
place the rooop component, consider the following
items:
• A 14.3 in. x 14.3 in. (363 mm x 363 mm)
[±0.1in. (3 mm)] square opening and hereinaer
referred to as “roof opening” is required. The
roof opening is part of the return air system of
the rooop component and must be finished in
accordance with NFPA 1192.
• The raer/joist support frames must be spaced
no greater than 16.0 in. (406 mm) on center. The
rooop component is designed to fit over an existing
roof vent opening.
• The distance between the roof and the RV ceiling
must be between 1.5 in. (38 mm) and 6.0 in.
(152mm).
• When no roof vent is available or when another
location is desired, an opening must be cut through
the roof and ceiling of the RV. This opening must
be located between the roof reinforcing members.
Consider these recommendations along with your
cooling needs:
– For a single rooop component: mount the
rooop component slightly forward of the RV’s
center (front to back) and centered from side to
side.
– For two rooop components: measuring from
the front of the RV and centering from side
to side, mount the first rooop component
at 1/3 the length of the RV and the second
rooop component at 2/3 the length of the RV.
4.5.1 Tilt requirements
When measuring for placement, confirm the following
tilt requirements.
1. Make all measurements while the RV is parked on a
level surface.
2. Install the rooop component on a flat and level roof
section.
3. Use the tilt allowance table to determine the
maximum acceptable roof tilt.
Tilt allowance
Model number Maximum tilt
(All directions)
B57915, B59516, B79516
540315, 540316
H540315, H540316,
FJX3473,FJX3573
15°

10 EN
Specifications Rooop Air Conditioner (Air Distribution Box, Mechanical Controls)
5 Specifications
This section provides the electrical specifications by model.
Model Nominal
Capacity
Cooling
(BTU HR)
Electrical
Rating
Compressor Amps Fan Motor Amps Refrigerant
R-410A
(oz)
Minimum
Wire Size1
AC Circuit
Protection2
(Installer
Supplied)
Minimum
Generator
Size3
(1 Unit/
2 Units)
Rated
Load
Locked
Rotor
Rated
Load
Locked
Rotor
B57915 13,500 115 VAC,
60 HZ,
1 ph
12.4 68.0 2.5 5.8 18.0 12 AWG 20 Amp 3.5 kW/
5.0 kW
B59516 15,000 13.3 70.0 2.0 5.6 18.3
B79516 15,000 13.3 70.0 2.0 5.6 20.1
540315.70X 13,500 12.4 63.0 3.0 8.5 18.5
540315.71X 13,500 12.4 68.0 3.0 8.5 18.5
H540315.72X 13,500 12.7 68.0 2.8 8.0 19.5
540316.70X 15,000 13.3 66.0 2.8 7.6 29.5
540316.71X 15,000 13.3 70.0 2.8 7.6 29.5
H540316.72X 15,000 13.2 70.0 2.8 8.0 20.1
FJX3473MWHAS 13,500 13.0 61.0 3.3 6.9 12.7
FJX3473MBKAS 13,500 13.0 61.0 3.3 6.9 12.7
FJX3573MWHAS 15,000 13.0 73.0 3.3 6.9 13.4
FJX3573MBKAS 15,000 13.0 73.0 3.3 6.9 13.4
1The wiring size indicated is for copper wiring up to 24  (7.3 m) in length. For wire lengths over 24  (7.3 m), consult the National Electrical Code for proper sizing.
2Circuit protection: a time delay fuse or circuit breaker is required.
3Dometic Corporation gives general guidelines for generator requirements. These guidelines come from experiences people have had in actual applications.
When sizing the generator, the total power usage of your RV must be considered. Generators may lose power at high altitudes and from lack of maintenance.

11
EN
Rooop Air Conditioner (Air Distribution Box, Mechanical Controls) Wiring diagrams
6 Wiring diagrams
This section provides the wiring diagrams for the
product.1
Compressor
6 Pin Conn
Motor
Fan
RUN
CAP
Herm
*Comp. Start Assist
Start
Cap
GRN/YEL
EVAP COIL
ENDPLATE
EVAP COIL
ENDPLATE
EVAP COIL
ENDPLATE
GRN/YEL
GRN/YEL
*Not Available for
Use on All Systems
BRN
WHT
WHT
BLK
BLU 1
2
3
4
5
6
YEL
RED
RED PTCR
RED
WHT
WHT
C
R S
O.L.
C
RED
7 FreshJet (FJX3473, FJX3573)
8 Brisk II (B57915, B59516, B79516 )
Compressor
6 Pin Conn
Motor
Run Cap
Fan
Herm Comp. Startter
*Start
Cap
GRN/YEL
GRN/YEL
*Not used on
some models
BRNWHT
WHT
BLK
BLU 1
2
3
4
5
6
YEL
RED
RED PTCR
WHT
WHT
C
R S
O.L.
C
*
RED
9 Blizzard and High Performance (540315, 540316, H540315,
H540316)
Elec Conn
From A/C Thermostat
Rotary Switch
BLK
YEL
RED
BLU C,4
L,3
H,6
GRN/YEL
BLU
BLK
GRN/YELG
L
NWHT
1
1 L1
2 H
4 C
2
3
4
5
6
10 ADB wiring diagram - all models
1Wiring Diagram Definitions; 115 VAC; 60 Hz 1 PH; Use Copper Conductors only
- - - - - - Field Wiring
---------- Factory Wiring
• Line Splice

12 EN
Pre-installation Rooop Air Conditioner (Air Distribution Box, Mechanical Controls)
7 Pre-installation
WARNING: FIRE OR ELECTRICAL SHOCK
HAZARD. Failure to obey these warnings
could result in death or serious injury.
• Shut off the gas supply, disconnect the 115 VAC
power from the RV, and disconnect the positive
(+) 12VDC terminal from the supply battery before
drilling or cutting into the RV.
• Make sure there are no obstacles such as wires or
pipes inside the RV’s roof.
• Provide grounding in compliance with all applicable
electrical codes.
CAUTION: LIFTING HAZARD.
Use proper liing technique and control when
liing the rooop component. Two people are
required to li the rooop component to the roof.
Failure to obey this caution could result in minor or
moderate injury.
NOTICE: Failure to follow these notices could
result in damage to the rooop component and/
or the RV.
• Never create a low spot on the RV roof.
• Maintain the structural integrity of the RV roof. The
roof must be designed to support 130 lbs (59 kg)
when the RV is in motion. Normally, a 200 lb (91 kg)
static load design will meet this requirement.
• Read this entire section before beginning the
installation.
This section describes how to install and set up the unit.
7.1 Determining your cooling needs
When determining your cooling requirements, consider
the following items:
• The size of the RV
• The RV window area (which could increase heat gain)
• The amount of insulation in the walls and the roof
• The geographical location where the RV will be used
• The personal comfort level required
7.2 Preparing the RV roof opening
NOTICE: The roof opening must be structurally framed
to provide adequate support and to prevent air from
being drawn from the roof cavity. Framing stock with
0.75 in. (19 mm) or more thickness must be used.
Remember to provide an entrance hole for power
supplies at the front of the opening. See Figure 12.
This section describes how to prepare the RV roof
opening.
7.2.1 Using an existing roof vent opening
IIf the roof does not have an existing roof vent, skip
to “Making a new roof opening” on page12.
This section describes how to prepare the RV roof when
using an existing vent.
1. Shut off the gas supply, disconnect the 115 VAC
power from the RV, and disconnect the positive (+)
12VDC terminal from the supply battery.
2. Unscrew and remove the roof vent.
3. Remove the caulking compound around the
opening.
4. Seal the screw holes and seams where the roof
gasket will be located. Use a good grade of
all-weather sealant.
5. Measure the roof opening (review “Placement
requirements” on page9). If the roof opening is
within specifications, skip to “Routing the wiring” on
page13.
6. If the opening needs to be resized, proceed to
“Making a new roof opening” on page12.
– If the opening exceeds 14.4 x 14.4 in.
(366 x 366mm), it will be necessary to reduce the
size of the opening.
– If the opening is less than 14.1 x 14.1in.
(358 x 358mm), it ill be necessary to enlarge the
opening.
7.2.2 Making a new roof opening
IIf the roof has an existing roof vent, see “Using an
existing roof vent opening” on page12.
This section describes how to prepare the RV roof when
making a new roof opening.

13
EN
Rooop Air Conditioner (Air Distribution Box, Mechanical Controls) Pre-installation
1. Shut off the gas supply, disconnect the 115 VAC
power from the RV, and disconnect the positive (+)
12VDC terminal from the supply battery.
2. Carefully mark the required roof opening. See
“Placement requirements” on page9.
qq
ww
ee
11 Structure for a new roof opening
qIncorrect eCorrect
wCorrect
3. Make sure the new opening does not compromise
the roof’s structural integrity.
– Do not cut the roof structure or the raers.
– The raers should remain supported by a cross
beam.
– The opening should be between the raers.
4. Carefully cut the required roof opening.
qq
ww
ee
12 Structural framing for a new roof opening
q0.8 in. (20 mm)
Minimum Width for
the Framing Stock
e15.0 in. (381 mm)
Exposed Length
of 115 VAC Power
Supply Wire
w0.3 in. (8 mm)
Minimum Width for
Access Hole
5. Frame the opening so it will not collapse when
bolting the rooop component down.
6. At the front of the frame opening, leave or create
an access hole to allow for the length of exposed
115VAC power supply wiring required to complete
the installation.
7. Using the roof opening as a guide, cut a matching
hole in the ceiling of the RV interior.
7.3 Routing the wiring
IThe power must be on an appropriately-sized
separate time-delay fuse or circuit breaker. See
“Specifications” on page10.
This section describes how to route the wiring for the
rooop component.
1. Position the copper 115 VAC power supply wire, with
ground, in the front portion of the roof opening.

14 EN
Pre-installation Rooop Air Conditioner (Air Distribution Box, Mechanical Controls)
2. Route the 115 VAC power supply wire from the
time-delay fuse or circuit breaker box to the roof
opening. Use a listed/certified non-metallic sheathed
single strand cable. See “Specifications” on
page10.
IIf an AC or a vent fan were removed, the existing
power supply wire may be used provided it is of the
proper type, size, and location, and if it is correctly
fused.
3. Make sure that at least 15.0 in. (381 mm) of the
115 VAC power supply wire extends into the roof
opening to ensure an easy connection at the junction
box.
4. Protect the 115 VAC power supply wire where it
passes into the opening according to local and
national standards.
7.4 Positioning the rooop
component
NOTICE: Do not slide the rooop component along a
surface. Otherwise, damage to the gasket on the bottom
of the rooop component could occur and cause a leak.
1. Remove all the contents from the carton and discard
the carton.
2. Place all the ADB kit contents in the RV. The ADB kit
contains mounting hardware for the ADB that will be
installed inside the RV.
3. Move the rooop component to the roof.
qq
ww
13 Placing the rooop model unit
qFront of the Rooop
Component
wRoof Opening
4. Li and place the rooop component over
the prepared opening using the gasket on the
rooop component as a guide.
IThe outside work is complete. Minor adjustments
can be made from inside the RV if required.
7.5 Preparing to work inside the RV
This section describes the interior preparation.
1. Bring the ADB kit inside the RV. The box contains the
mounting hardware for the ADB that will be used
inside the RV.
qq
14 Centering the rooop model unit from inside the RV
qRoof Gasket
2. From inside the RV, check the gasket alignment of
the rooop component over the roof opening. If
necessary, adjust the rooop component from below
by slightly pushing up.
qq
ww
15 Return air opening
qElectrical Cord wCeiling Thickness

15
EN
Rooop Air Conditioner (Air Distribution Box, Mechanical Controls) Installation
3. Reach up into the return air opening of the
rooop component and pull the rooop component
electrical cord down for later connection.
4. Remove the ADB and the mounting hardware from
the carton. See “ADB components” on page6
for the parts configuration.
8 Installation
8.1 Installing the foam dividers
Roof thicknesses vary among RVs and the ADB
installation may require additional foam to fill any gaps in
thicker roofs.
This section describes how to determine if additional
foam dividers are required, the number required, and
the installation method.
ww
qq
ee
16 Measuring the roof thickness for foam divider installation
qCeiling Opening eRoof Thickness
wRooop Model Unit
Basepan
1. Measure the roof thickness, from a flat surface of the
installed rooop component’s basepan to the ceiling
opening inside the RV.
qq
ww
ee
uu
yy
tt
rr
17 Stacking the foam dividers and placement location
qStacked Foam
Dividers
tFoam Divider -
0.4in. (10mm) (2)
wRoof Thickness yFoam Divider -
1.2in. (30mm) (3)
eTop Foam -
0.4in. (10mm) (1)
uADB Adaptor (1)
rTop Foam Ring -
0.4in. (10mm) (1)
2. Identify the different types and sizes of foam dividers.

16 EN
Installation Rooop Air Conditioner (Air Distribution Box, Mechanical Controls)
8.1.1 Roof thickness 1.25to 5.5 in. (32 to
152 mm)
All models
Roof
Thickness
1.25in.
(32 mm)
1.5 in.
(38 mm)
2.0in.
(51mm)
2.5in.
(64mm)
3.0in.
(76 mm)
3.5 in.
(90 mm)
4.0in.
(102 mm)
4.5in.
(114mm)
5.0in.
(127 mm)
5.5in.
(140 mm)
Total Divider
Thickness
1.7in.
(50 mm)
2.4in.
(60 mm)
2.8in.
(70 mm)
3.5 in.
(90 mm)
3.9 in.
(100 mm)
4.3in.
(110 mm)
4.7in.
(120 mm)
5.5in.
(140 mm)
5.9in.
(150 mm)
6.3in.
(160 mm)
Top Foam
0.4 in.
(10 mm)
x x x x x x x x x x
Top Foam
Ring
0.4 in.
(10 mm)
x x x x x x x x x x
Foam
Divider
0.4 in.
(10 mm)
x x x x x x x
Foam
Divider
0.4 in.
(10 mm)
x x x
Foam
Divider
1.2 in.
(30 mm)
x x x x x x x
Foam
Divider
1.2 in.
(30 mm)
x x x x x
Foam
Divider
1.2 in.
(30 mm)
x x x
ADB
Adaptor
1.2 in.
(30 mm)
x x x x x x x x x x
1Up to 0.4 in. (10 mm) of compression of the foam dividers is acceptable and may be required in some instances.

17
EN
Rooop Air Conditioner (Air Distribution Box, Mechanical Controls) Installation
8.1.2 Roof thickness 6.0-7.5 in.
(152to191mm)
All models
Roof
Thickness
6.0in.
(152mm)2
6.5in.
(165mm)2
7.0in.
(178mm)2
7.5in.
(191mm)2
Total Divider
Thickness
7.0in.
(180mm)
7.5in.
(190mm)
7.9in.
(200mm)
8.3in.
(210mm)
Top Foam
0.4 in.
(10 mm)
x x x x
Top Foam
Ring
0.4 in.
(10 mm)
x x x x
Foam
Divider
0.4 in.
(10 mm)
x x x
Foam
Divider
0.4 in.
(10 mm)
x
Foam
Divider
1.2 in.
(30 mm)
x x
Foam
Divider
1.2 in.
(30 mm)
x x x x
Foam
Divider
1.2 in.
(30 mm)
x x x x
ADB Adaptor
1.2 in.
(30 mm)
x x x x
Spare2
Foam
Divider
1.2 in.
(30 mm)
x x x x
Spare2
Foam
Divider
1.2 in.
(30 mm)
x x x x
1Up to 0.4 in. (10 mm) of compression of the foam dividers is acceptable and may be
required in some instances
2To accommodate a roof thickness greater than 5.5 in. (140 mm), order the optional
accessory kit. See “Tools and materials” on page5.
1. Using the tables, determine the number and
combination of foam dividers required based on the
roof thickness.
qq
ww
ee
18 Confirming the foam divider height measurement
qFlat Surface of the
ADB
eFull Height
Measurement
(Equal to the Roof
Thickness)
wStack of Foam Dividers
2. Place the ADB face down on a stable, protected, flat
surface.
3. Stack the foam dividers required and place them onto
the ADB.
4. Measure the full height, from the flat surface of the
ADB to the top of the foam dividers to confirm the
full height is equal to the previously determined roof
thickness.
5. Adjust the number of foam dividers to reach the
correct full height, as necessary.

18 EN
Installation Rooop Air Conditioner (Air Distribution Box, Mechanical Controls)
ww
ee
qq
rr
0
19 Passing the wire through the filter notch
qFilter eADB Second Slot
wFilter Notch r115 VAC Power Supply Wire
and 6-pin Unit Electrical Cord
6. Slide out the filter to expose the filter notch.
7. Pass all of the available 115 VAC power supply wire
and 6-pin unit electrical cord through the filter notch
and through the second slot of the ADB.
8.2 Securing the unit
NOTICE: Overtightening could damage the
rooop component’s base pan or ceiling template. Not
enough torque will cause an inadequate roof seal, and
could cause a leak.
IAll models in this manual use a four bolt pattern to
secure the ADB kit.
This section describes how to secure the
rooop component to the roof.
1. For units that fit within the 14.0 x 14.0 in.
(366 x 366mm) ceiling opening, press the entire unit
up toward the basepan and into the ceiling opening.
2. Use the following figures to determine the proper
mounting pattern and bolt location.
AB
CD
20 Mounting bolt pattern - all models
ww
ww
ww
ww
qq
21 Mounting bolt location - all models
qCeiling Template wMounting Bolt
3. Start each mounting bolt by hand, through the
ceiling template and up into the rooop component
base pan.
4. Tighten the mounting bolts to the correct torque
specifications.
– For the FreshJet, tighten all four mounting bolts
evenly at 22.2 in. lbs (2.5 N·m).
– For all other models, tighten all four mounting
bolts evenly within 40 to 50 in. lbs (4.7 to
5.6N·m).

19
EN
Rooop Air Conditioner (Air Distribution Box, Mechanical Controls) Installation
8.3 Wiring the unit to the power
supply
oo
rr
ii
w
q
aa
ee
yy
tt
uu
22 Completing the wiring
qJunction Box Cover
Screws
yCable Connector
for 6-pin Unit Electrical
Cord (from the AC)
wJunction Box Cover uCable Connector
for 6-pin Unit Electrical
Cord (from the ADB)
eJunction Box iLive Black and Neutral
White Wires (from the
ADB)
r6-pin Unit Electrical
Cord (from the AC)
o115 VAC Power Supply
Wire (from the roof
opening)
tJunction Box Notch aStrain Relief
This section describes how to wire the power supply to
the rooop component.
1. Unscrew the two junction box cover screws, and
unsnap and remove the junction box cover.
2. Route the 6-pin unit electrical cord from the AC to the
junction box location.
3. Plug the 6-pin unit electrical cord from the AC into
the matching 6-pin cable connector in the junction
box. The plug is keyed and will only fit in one
direction.
4. To avoid damage, run the 6-pin unit electrical cord
through the notch on the side of the junction box.
5. Route the 115 VAC power supply wire from the roof
opening to the junction box location.
6. Thread the 115 VAC power supply wire through the
strain relief.
7. Secure the 115 VAC power supply wire by tightening
the two screws on the strain relief. Make sure not to
damage the 115 VAC power supply wire.
8.4 Connecting the power supply
ww
ee
rr
ttyy
qq
23 Junction box
qJunction Box Cover
Screws
rLive Black Wire
wJunction Box Cover tCopper Wire
eNeutral White Wire yGreen/Yellow
Ground Cord
This section describes how to connect the 115 VAC
power supply wire from the rooop component and the
6-pin unit electrical cord from the AC.
1. Connect the white neutral wires together, using
appropriately-sized connectors.
2. Connect the black live wires to each other, using
appropriately-sized connectors.
3. Connect the bare copper wire to the green/yellow
ground cord, using appropriately-sized connectors.

20 EN
Operation Rooop Air Conditioner (Air Distribution Box, Mechanical Controls)
4. Tape the connectors to the 115 VAC power supply
wire to ensure they do not vibrate loose.
5. Push the connected wires into the junction box.
6. Align the junction box cover to the notch on the side
of the junction box.
7. Snap the junction box cover into place and secure
the junction box cover with the two junction box
cover screws.
8.5 Finalizing the installation
This section describes how to complete the ADB installation.
1. Push the filters in completely.
qq
24 Attaching the control knobs
qControl Knobs (2)
2. Align the keyed control knobs to the control knob
stems on the ADB.
3. Gently push the control knobs into place.
qq
25 Attaching the center cover
qCenter Cover
4. Clip the center cover to the ADB.
5. Turn on the power supply.
6. Verify that all the unit features work.
IRead the following operating instructions before
attempting to run the unit.
9 Operation
This section describes the rooop component’s
operating controls and settings.