Dometic GP-ADV-LiFePO4-300 User manual

Technology Lithium Iron Phosphate
Nominal Voltage 12.8 V
Fully Charged Voltage (FC) 14.6V
Fully Discharged Voltage (FD) 9.2V
Capacity (Ah) 300Ah
Recommended Discharge
Terminated Voltage
Max Continuous Charge Current
10V
Recommended Charge
Voltage 14.2V
300A
Battery Discharge Terminated
Voltage 9.2V
Heater Function
Standard Charge Method
0.2C CC (constant current) charge to FC, then
CV (constant voltage FC) charge till charge current
decline to ≤0.05C
Battery pack includes heater for heating cell module temper-
ature up when battery pack is charged in a freezing en-
vironment
Inner Resistance ≤10mΩ
UL2054, CE, UKCA, UN38.3
Operating Temperature
Charge: -4°F (-20°C) to 131°F (55°C)
Discharge: -4°F (-20°C) to 131°F (55°C)
Storage Temperature1
1 month > 113°F (45°C) to 131°F (55°C) - Max 80% RH
3 months > 77°F (25°C) to 113°F (45°C) - Max 80% RH
6 months > -4°F (-20°C) to 77°F (25°C) - Max 80% RH
177°F (20˚C) ±5 is the recommended storage temperature at 60% State of Charge while
being in Power Off mode.
Humidity
20uA in Shutdown Mode
BMS Leakage Current
P+ / P- : M8
Terminal
19.6in x 14.9in x 8.11in (498mm x 379mm x 206mm)
Dimensions (LxWxH)
70.5lbs (32kg)
Weight
Operating: 5% to 90 % RH
Storage: 45% to 85% RH
GP-ADV-LiFePO4-300
WARNINGS
Only wire 8 batteries maximum in parallel
Do not get wet
Wire a maximum of 4 in series
Find tech tips, manuals and support at gopowersolar.com
BATTERY SPECIFICATIONS
SPECIFICATIONS
Certifications
Negative Terminal
Positive Terminal
Power Button (LED)
RV-C 1
RV-C 2
No.
Descrip�on
1
2
3
4
5
NO. DESCRIPTION
ADVANCED LITHIUM
BATTERY
Quick Start Guide
4 53
2
1
UN38.3
Scan for
full
manual

LED Battery Mode Definition
Solid light Power on mode
Blinking light Sleep/Reserve mode
OFF Power off mode
LED (POWER BUTTON) INDICATORS
CAN PORT WIRING
HOW TO USE
NOTE:
To prevent a surge current, perform a “pre-discharge” as outlined in the steps
below.
Batteries are in Power Off mode when unboxed. Press the Power button for 3
seconds to turn on. If it doesn’t turn on, you will need to charge the battery.
The batteries need to be configured before they can be used. Please see
battery manual for instructions on battery configuration. Battery pack will enter
shutdown mode after 6 seconds in Power OFF mode.
VARIOUS POWER MODES
Step 1 - Ensure all batteries are in Power Off mode.
Step 2 - Connect batteries following the series or parallel connection diagrams found at
gopowersolar.com/advanced-lithium-wiring. Cable 2 must be installed for
each battery pack followed by a Cable 3 cable on the last battery.
Step 3 - Ensure battery pack terminals are correctly installed and connected to the inverter
system.
Step 4 - Press the power button on one of the battery packs for 3 seconds to wake up all
battery packs from Power Off mode. The LED indicator will turn on.
INTERFACE DESCRIPTION
Reserve
Capacity
Reserve
Capacity
Power off
Press and hold for 3s and release
Press and hold for 8s and release
Press and hold for 8s and release
Press and hold for 8s and release
Press and hold for 3s and release
Press and hold for 3s and release
Press and hold for 3s and release
or charge battery to above 5Ah
Press button for more than 3 seconds and release. The battery will enter sleep mode.
The LED will blink. Power off mode should only be used for long term storage or to
reset the BMS. Use sleep mode to disable output power of batteries.
Scan the QR code to download the Go Power! Connect App for
use with the Sun Cycle®Advanced Lithium Battery.
BLUETOOTH®APP
Power on
Power on
Power on
Power off
Power off
Sleep Mode
Sleep
Mode
*cables purchased separately
Pack 1-1
Pack N-1 Pack N-2 Pack N-3 Pack N-4
RV-C system
(if applicable)
Cable 3
Cable 1
RV system add 120ohm
resistor in CAN1
Pack 2-1 Pack 3-1 Pack 4-1
Cable 2