Dometic PLB40 User manual

PLB40
Portable lithium iron phosphate
battery pack
Operating manual . . . . . . . . . . . . . . . . . . . . .4
Batterie lithium fer phosphate
portable
Notice d’utilisation . . . . . . . . . . . . . . . . . . . 17
Batería de litio-ferrofosfato
portátil
Instrucciones de uso . . . . . . . . . . . . . . . . . .30
EN
FR
ES
ENERGY & LIGHTING
BATTERIES
PLB40-O-US.book Seite 1 Donnerstag, 24. Januar 2019 3:23 15

PLB40
2
1
2
3
4
1
2
13 4 87
6
5 9
2
PLB40-O-US.book Seite 2 Donnerstag, 24. Januar 2019 3:23 15

PLB40
3
!
211111 3 4 5 6
78
9
3
PLB40-O-US.book Seite 3 Donnerstag, 24. Januar 2019 3:23 15

EN
Explanation of symbols PLB40
4
Please read this instruction manual carefully before first use, and store it in
a safe place. If you pass on the product to another person, hand over this
instruction manual along with it.
Table of contents
1 Explanation of symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
2 General safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
3 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
4 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
5 Technical description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
6 Using the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
7 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
8 Maintaining and cleaning the product. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
9 Limited warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
10 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
11 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
1 Explanation of symbols
!
!
A
WARNING!
Safety instruction: Failure to observe this instruction can cause death
or serious injury.
CAUTION!
Safety instruction: Failure to observe this instruction can lead to injury.
NOTICE!
Failure to observe this instruction can cause material damage and impair
the function of the product.
PLB40-O-US.book Seite 4 Donnerstag, 24. Januar 2019 3:23 15

EN
PLB40 General safety instructions
5
I
2 General safety instructions
The manufacturer accepts no liability for damage in the following cases:
•Damage to the product resulting from mechanical influences and incorrect
connection voltage
•Alterations to the product without express permission from the manufacturer
•Use for purposes other than those described in the operating manual
The declaration of conformity can be requested from the manufacturer (contact infor-
mation on the back).
Note the following basic safety information when using electrical devices to protect
against:
•Electric shock
•Fire hazards
•Injury
2.1 General safety
!WARNING! INSTRUCTIONS PERTAINING TO RISK OF FIRE, ELEC-
TRIC SHOCK, OR INJURY TO PERSONS.
•Only use the device as intended.
•Disconnect the device from the mains
– Before cleaning and maintenance
–Afteruse
– Before changing a fuse
•To reduce risk of damage to the electric plug and cord, pull the plug
rather than the cord when disconnecting the device.
•Do not use a device that is damaged or modified. Damaged or modi-
fied devices may exhibit unpredictable behavior resulting in fire,
explosion or risk of injury.
•Do not operate the device with a damaged cord or plug, or a dam-
aged output cable.
•Do not disassemble the device, take it to a qualified service person
when service or repair is required. Incorrect reassembly may result in a
risk of fire or electric shock.
NOTE
Supplementary information for operating the product.
PLB40-O-US.book Seite 5 Donnerstag, 24. Januar 2019 3:23 15

EN
General safety instructions PLB40
6
•To reduce the risk of electric shock, unplug the device from the outlet
before attempting any instructed servicing.
•Do not expose to liquid, vapor, rain, sleet, snow or the like.
•The device shall be stored indoors and protected from the elements.
•Never smoke or allow a spark or flame in vicinity of battery or engine.
•When charging the device, work in a well ventilated area and do not
restrict ventilation in any way.
•Do not expose the device to fire or excessive temperature. Exposure
to fire or temperature above 130°C(266°F)maycauseexplosion.
•Electrical devices are not toys.
Always keep and use the device out of the reach of children.
•Children must be supervised to ensure that they do not play with the
device.
ANOTICE! MATERIAL DAMAGE.
•Do not insert foreign objects into the output or input terminals.
•Do not put fingers or hands into the device.
•Do not attempt to replace the internal battery cells.
•Before using for the first time, charge your battery pack using one of
the methods described in chapter “Charging the lithium iron phos-
phate battery pack” on page 11.
•Before using the device for the first time, check that the voltage speci-
fication on the rating plate matches that of the power supply.
•Never pull on the power cord to unplug the device from the power
socket.
•Store the device in a dry and cool place.
2.2 Operating the device safely
!WARNING! INSTRUCTIONS PERTAINING TO RISK OF FIRE, ELEC-
TRIC SHOCK, OR INJURY TO PERSONS.
•Only use the charger supplied to charge the device. Use of an attach-
ment not recommended or sold by the manufacturer may result in a
risk of fire, electric shock, or injury to persons.
•The power socket to which the device is connected must be close by
and easily accessible.
PLB40-O-US.book Seite 6 Donnerstag, 24. Januar 2019 3:23 15

EN
PLB40 Scope of delivery
7
!CAUTION! FIRE AND/OR EXPLOSION HAZARD.
•Do not operate the device
– In the vicinity of corrosive fumes
– In the vicinity of combustible materials
– In areas where there is a danger of explosions
•Do not place the device next to heat sources such as fires.
•Place the device in a shady place. Avoid direct sun exposure in hot
and humid surroundings for a proper usage.
ANOTICE! MATERIAL DAMAGE.
•Do not disconnect any cables when the device is still in use.
•Only use the device in upright position.
3Scopeofdelivery
4 Intended use
The portable lithium iron phosphate battery pack is for use in camping application. It
comes with four outlets to power devices like tablet, mobile phone, portable
fridge/freezer etc.
The battery pack is suitable for
•the connection to 12 V appliances with low power consumption e.g. small invert-
ers up to 150 W,
•the connection to a laptop with an additional 150 W inverter connected to the
12 V DC connection socket output.
It is not allowed
•to use the battery pack as a starter battery for a vehicle,
•to use two battery packs in parallel connection.
No. in
fig. 1, page 2 Description
1 Portable lithium iron phosphate battery pack
2 DC charge cable
3 AC power supply unit
4 2x DC Fuse
PLB40-O-US.book Seite 7 Donnerstag, 24. Januar 2019 3:23 15

EN
Technical description PLB40
8
5 Technical description
The portable lithium iron phosphate battery pack (LiFePO4) enables mobile power
supply for portable refrigeration, USB devices and small inverters up to 150 W con-
tinuous output.
A DC consumer unit (e.g. a portable refrigeration) can be simultaneously supplied
with power while the lithium iron phosphate battery is being charged via the power
supply unit.
The housing is shock, heat and UV resistant.
The lithium iron phosphate battery can be charged in three ways:
•via the supplied AC/DC charger on the AC mains (max. 8 A)
•via DC connection through vehicle alternator (max. 8 A)
•via DC connection through solar panel
The device has the following protective functions:
•Overtemperature, undertemperature protection
•Overvoltage protection
•Undervoltage protection
•Overcurrent protection
•Short circuit protection
•Incorrect polarity protection
PLB40-O-US.book Seite 8 Donnerstag, 24. Januar 2019 3:23 15

EN
PLB40 Technical description
9
5.1 Connections and display
5.2 Display
No. in
fig. 2, page 2 Description
1 Power button
2 Display (LCD)
3 2 x USB socket (5 V, max. 4.2 A overall)
412Vg 2-pin connection output to portable refrigeration
512Vg heavy duty connection socket output for portable
refrigeration and 12 V applicances
6 Adjustable handle
7 2x fuse holder
8 AC/DC adapter input socket
9 DC/DC Anderson™ SB™ input socket
No. in
fig. 3, page 3 Description
1 A failure occurred (chapter “Troubleshooting” on
page 13).
2 See chapter “Troubleshooting” on page 13.
3 See chapter “Troubleshooting” on page 13.
4 The battery pack supplies energy to an USB device.
5 The battery pack supplies energy to a device connected to
the 2-PIN output.
6 The battery pack supplies energy to a device connected to
the DC output.
7 State of charge as a percentage
!
PLB40-O-US.book Seite 9 Donnerstag, 24. Januar 2019 3:23 15

EN
Using the appliance PLB40
10
6 Using the appliance
6.1 Before first use
➤Before first use or storing plug the battery pack into the wall charger until it is fully
charged.
➤Observe the information given in chapter “Charging the lithium iron phosphate
battery pack” on page 11.
6.2 Starting and switching off
Starting the lithium iron phosphate battery pack
➤Press the power button (fig. 21, page 2) for at least 3 seconds to start the
device.
✓The device emits 2 beeps.
✓The display shows the operational status:
: the lithium iron phosphate battery is being charged
: the lithium iron phosphate battery is being discharged
: the lithium iron phosphate battery is on idle mode
✓The display switches off automatically after 1 minute.
Switching the display on
➤Press the power button (fig. 21, page 2) briefly to switch on the display.
8 Battery is being discharged
Battery is being charged
Battery is being charged and discharged at the same time
9 See chapter “Troubleshooting” on page 13.
No. in
fig. 3, page 3 Description
PLB40-O-US.book Seite 10 Donnerstag, 24. Januar 2019 3:23 15

EN
PLB40 Using the appliance
11
Switching off the lithium iron phosphate battery pack
The battery pack switches off automatically after 24 hours if no load and no charger
are connected.
➤Press the power button (fig. 21, page 2) for at least 3 seconds to switch the
device off.
✓The device emits 1 beep.
✓The display switches off.
6.3 Charging the lithium iron phosphate battery pack
!
➤Adjust the handle upwards.
➤Place the lithium iron phosphate battery on a firm base.
Charging with the power supply unit
➤Connect the power supply unit to the connection socket (fig. 28, page 2).
➤Connect the power supply unit to the AC mains.
✓The symbol lights up.
✓The display shows the charging status.
Charging with the smart alternator, 12 V accessory socket or solar panel
➤Connect the charge cable to the connection socket (fig. 29, page 2).
➤Connect the DC plug to the DC inlet Anderson socket on battery side.
✓The symbol lights up the battery state of charge as a percentage.
✓The display shows the charging status.
WARNING! FIRE AND/OR EXPLOSION HAZARD.
Lithium iron phosphate batteries that are charged with too high voltage
can ignite. Use 8 to 25 V input voltage to charge the battery pack.
PLB40-O-US.book Seite 11 Donnerstag, 24. Januar 2019 3:23 15

EN
Using the appliance PLB40
12
➤If charging the battery pack with a solar panel, observe the following require-
ments:
–Use without a solar controller:
Ensure that the solar panel outputs between 8 – 25 V DC and a maximum
charging current of 10 A.
–Use with a solar controller:
Ensure the solar charger does not need a counter voltage from the battery
side to start charging. Ensure that the maximum charging current is 10 A
(check with the solar panel manufacturer).
6.4 Checking the charge level
➤Press the power button (fig. 21, page 2).
✓The display shows the battery state of charge as a percentage.
✓The symbol flashes when the battery capacity is below 20 %.
6.5 Connecting consumer devices
fig. 2, page 2
➤Open the cap for the desired device:
–USBdevices(3)
–2-pin12VDCsocketoutlet(4)
–12VDCsocket(5)
➤Insert your device’s plug into the corresponding socket.
✓The symbol and the related output symbol light up.
6.6 Replacing fuses
➤Ensure that the battery pack is not connected to AC/DC or DC/DC charger.
➤Disconnect all loads.
➤Press the power button for at least 3 s to switch the battery pack off.
➤Undo the fuse holder.
➤Replace the fuse with a 20 A 3 AG glass-slow acting fuse.
PLB40-O-US.book Seite 12 Donnerstag, 24. Januar 2019 3:23 15

EN
PLB40 Troubleshooting
13
7 Troubleshooting
Problem Cause Remedy
The display shows the
warning symbol and the
low / high temperature sym-
bol flashes. An error sound is
continuously beeping dur-
ing charging.
The ambient temperature for
charging the device is too
low / high.
Stop charging the device.
Turn the device off. Wait until
the ambient temperature
comes to a permitted value
(chapter “Technical data” on
page 15).
The display shows the
warning symbol and the
low / high temperature sym-
bol flashes. The device
beeps for 15 seconds and
then switches off automati-
cally during discharging.
The ambient temperature for
discharging the device is too
low / high.
Stop discharging the device.
Turn the device off. Wait until
the ambient temperature
comes to a permitted value
(chapter “Technical data” on
page 15).
The display shows the warn-
ing symbol and the fuse
blown symbol flashes. An
error sound is continuously
beeping for 30 seconds.
The DC output fuse has
blown. Additionally the DC
symbol flashes in the display.
Turn the device off.
Change the DC fuse (chapter
“Replacing fuses” on
page 12).
The 2-PIN fuse has blown.
Additionally the 2-PIN
symbol flashes in the display.
Turn the device off.
Change the 2-PIN fuse (chap-
ter “Replacing fuses” on
page 12).
The display shows the warn-
ing symbol and the charge
arrow symbol flashes. An
error sound is continuously
beeping.
The input voltage of the
charger is wrong.
Turn the charger off. Connect
a charger with the standard
charge voltage (chapter
“Technical data” on
page 15).
The display shows the warn-
ing symbol. The discharge
arrow and either the USB or
2-pin or DC symbol flashes.
An error sound is beeping for
60 seconds.
Over current protection was
triggered.
Turn the device off. Release
some of the load before
switching the device on
again.
Short circuit protection was
triggered.
Turn the device off. Clear the
short circuit before switching
the device on again.
PLB40-O-US.book Seite 13 Donnerstag, 24. Januar 2019 3:23 15

EN
Maintaining and cleaning the product PLB40
14
8 Maintaining and cleaning the product
A
➤Occasionally clean the product with a damp cloth.
A
9 Limited warranty
LIMITED WARRANTY AVAILABLE AT
DOMETIC.COM/WARRANTY.
IF YOU HAVE QUESTIONS OR TO OBTAIN A COPY OF THE LIMITED WARRANTY
FREE OF CHARGE, CONTACT THE DOMETIC WARRANTY DEPARTMENT:
DOMETIC CORPORATION
CUSTOMER SUPPORT CENTER
1120 NORTH MAIN STREET
ELKHART, INDIANA 46514
1-800-544-4881 OPT. 3
The battery symbol is flash-
ing. An error sound beeps
every 3 seconds for 10 times.
After the beeps the device
switches off automatically.
The battery capacity is 0 %. Charge the device.
NOTICE! MATERIAL DAMAGE.
•Do not use sharp or hard objects or cleaning agents for cleaning as
these may damage the product.
•Do not use alcohol based cleaning materials for cleaning the gloss
top cover.
NOTICE! MATERIAL DAMAGE.
Fully charge the lithium iron phosphate battery at least every six months.
Overloading the battery or storing it for too long without charging it may
cause permanent damage to the battery.
Problem Cause Remedy
PLB40-O-US.book Seite 14 Donnerstag, 24. Januar 2019 3:23 15

EN
PLB40 Disposal
15
10 Disposal
➤Place the packaging material in the appropriate recycling waste bins wherever
possible.
MIf you wish to finally dispose of the product, ask your local recycling centre
or specialist dealer for details about how to do this in accordance with the
applicable disposal regulations.
BProtect the environment!
Do not dispose of any batteries with general household waste.
Return defective or used batteries to your retailer or dispose of them at
collection points.
11 Technical data
PLB40
Battery type: Lithium iron phosphate/LiFePO4
Battery rated capacity: 40 Ah
Rated battery voltage: 12.8 Vg
Rated output current (derating of 5 % per
channel/ per °C for temperatures above
40 °C (104 °F)):
DC socket: 15 A
2-PIN socket: 15 A
USB socket: 2.4 A per socket, 4.2 A overall
Input voltage range: 8 – 25 Vg
Maximum DC/DC charging current: 8 A
Lifecycle:Potential lifecycle at 80 % depth of discharge
(depending on charge cycle and storage
condition)
Up to 2000 charging cycles
Rated input voltage:
Power supply unit / battery:
PWM solar controller:
12 Vg
14.6 Vg
Cut off voltage: 10 – 11 Vg
PLB40-O-US.book Seite 15 Donnerstag, 24. Januar 2019 3:23 15

EN
Technical data PLB40
16
Power supply unit
Maximum self-discharge rate at 25 °C
(77 °F):
5 % per month
Ambient temperature for operation: 0 °C to +45 °C (+32 °F to +113 °F)
Dimensions(LxWxH): 197x197x257mm(7.76x7.76x10.12in)
Weight: 7.54 kg (16.62 lbs)
Inspection/certification:
PLB40
AC supply (power supply unit):
AC Input:
DC output:
100 – 240 Vw/ 50/60 Hz, 2.5 A
12 Vg, 10 A
PLB40
UN 38.3
PLB40-O-US.book Seite 16 Donnerstag, 24. Januar 2019 3:23 15

EN
PLB40 Signification des symboles
17
Veuillez lire ce manuel attentivement avant de mettre l'appareil en service
et conservez-le. En cas de passer le produit, veuillez le transmettre au
nouvel acquéreur.
Sommaire
1 Signification des symboles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
2 Consignes générales de sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
3 Contenu de la livraison . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4 Usage conforme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
5 Description technique . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
6 Utilisation de l’appareil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
7 Guide de dépannage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
8 Entretien et nettoyage du produit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
9 Limitation de la garantie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
10 Mise au rebut. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
11 Caractéristiques techniques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
1 Signification des symboles
!
!
A
AVERTISSEMENT!
Consigne de sécurité : le non-respect de ces consignes peut entraîner
la mort ou de graves blessures.
ATTENTION!
Consigne de sécurité : le non-respect de ces consignes peut entraîner
des blessures.
ATTENTION!
Le non-respect de ces consignes peut entraîner des dommages
matériels et des dysfonctionnements du produit.
PLB40-O-US.book Seite 17 Donnerstag, 24. Januar 2019 3:23 15

EN
Consignes générales de sécurité PLB40
18
I
2 Consignes générales de sécurité
Le fabricant décline toute responsabilité pour des dommages dans les cas suivants :
•des sollicitations mécaniques et une tension de raccordement incorrecte ayant
endommagé le matériel
•des modifications apportées au produit sans autorisation explicite de la part du
fabricant
•une utilisation différente de celle décrite dans la notice
La déclaration de conformité peut être demandée auprès du fabricant (coordonnées
au dos).
Lors de l’utilisation d’appareils électriques, les consignes générales de sécurité sui-
vantes doivent être respectées afin d’éviter :
•une décharge électrique,
•un incendie,
•des blessures.
2.1 Sécurité générale
!AVERTISSEMENT! INSTRUCTIONS RELATIVES AUX RISQUES
D’INCENDIE, DE CHOC ÉLECTRIQUE OU DE BLESSURES CORPO-
RELLES.
•Utilisez l’appareil conformément à l’usage pour lequel il a été conçu.
•Débranchez l’appareil du secteur
– avant tout nettoyage et entretien
– après chaque utilisation
– avant le changement d’un fusible
•Pour réduire le risque d’endommagement de la fiche et du cordon
électrique, tirez sur la fiche plutôt que sur le cordon lorsque vous
débranchez l’appareil.
•N’utilisez pas un appareil endommagé ou modifié. Les appareils
endommagés ou modifiés peuvent présenter un comportement
imprévisible pouvant entraîner un incendie, une explosion ou un
risque de blessure.
REMARQUE
Informations complémentaires sur l'utilisation du produit.
PLB40-O-US.book Seite 18 Donnerstag, 24. Januar 2019 3:23 15

EN
PLB40 Consignes générales de sécurité
19
•N’utilisez pas l’appareil avec un cordon ou une fiche endommagés,
ou un câble de sortie endommagé.
•Ne démontez pas l’appareil mais confiez-le à un technicien qualifié
lorsqu’un entretien ou une réparation est nécessaire. Un remontage
incorrect peut entraîner un risque d’incendie ou de choc électrique.
•Pour réduire le risque de choc électrique, débranchez l’appareil de la
prise de courant avant d’entreprendre toute opération d’entretien
recommandée.
•Ne pas exposer à des liquides, de la vapeur, à la pluie, aux giboulées,
à la neige ou similaire.
•L’appareil doit être entreposé à l’intérieur et protégé des intempéries.
•Ne jamais fumer ou laisser une étincelle ou une flamme à proximité de
la batterie ou du moteur.
•Lors de la charge de l’appareil, travaillez dans une zone bien aérée et
ne limitez en aucune façon la ventilation.
•N’exposez pas l’appareil à un incendie ou une températureexcessive.
Une exposition à un incendie ou une température supérieure à 130 °C
(266 °F) peut provoquer une explosion.
•Les appareils électriques ne sont pas des jouets pour enfants.
Placez et utilisez l’appareil hors de leur portée.
•Les enfants doivent être surveillés pour s’assurer qu’ils ne jouent pas
avec l’appareil.
AATTENTION! DOMMAGES MATÉRIELS.
•N’introduisez aucun corps étranger dans les bornes de sortie ou
d’entrée.
•Ne glissez ni les doigts ni les mains dans l’appareil.
•N’essayez pas de remplacer les cellules internes de la batterie.
•Avant la première utilisation, chargez la batterie en utilisant l’une des
méthodes décrites dans chapitre «Charge de la batterie lithium fer
phosphate» à la page 24.
•Avant la mise en service de l’appareil, vérifiez que la tension indiquée
sur la plaque signalétique correspond à l’alimentation électrique dont
vous disposez.
•Ne tirez jamais sur le câble de raccordement de l’appareil pour sortir
la fiche de la prise.
•Stockez l’appareil dans un endroit frais et sec.
PLB40-O-US.book Seite 19 Donnerstag, 24. Januar 2019 3:23 15

EN
Contenu de la livraison PLB40
20
2.2 Consignes de sécurité concernant le fonctionnement
de l’appareil
!AVERTISSEMENT! INSTRUCTIONS RELATIVES AUX RISQUES
D’INCENDIE, DE CHOC ÉLECTRIQUE OU DE BLESSURES CORPO-
RELLES.
•Utilisez exclusivement le chargeur fourni pour charger l’appareil. L’uti-
lisation d’un accessoire non recommandé ou non vendu par le fabri-
cant peut entraîner un risque d’incendie, de choc électrique ou de
blessures corporelles.
•La prise à laquelle est raccordé l’appareil doit être à proximité et faci-
lement accessible.
!ATTENTION! RISQUE D’INCENDIE ET/OU D’EXPLOSION.
•N’utilisez pas l’appareil
– à proximité de vapeurs agressives,
– à proximité de matériaux inflammables,
– ou dans un environnement explosif.
•Ne placez pas l’appareil à proximité de sources de chaleur telles que
des incendies.
•Placez l’appareil dans un lieu ombragé.Évitez touteexposition directe
au soleil dans un environnement chaud et humide pour un usage
approprié.
AATTENTION! DOMMAGES MATÉRIELS.
•Ne débranchez pas de câbles pendant le fonctionnement de l’appa-
reil.
•Utilisez l’appareil en position verticale uniquement.
3 Contenu de la livraison
Pos. dans
fig. 1, page 2 Description
1 Batterie lithium fer phosphate portable
2 Câble chargeur CC
3 Bloc d’alimentation CA
4 2x fusible CC
PLB40-O-US.book Seite 20 Donnerstag, 24. Januar 2019 3:23 15