Dormakaba LA GARD 700 Series User manual

LA GARD SERIES 700
System User Guide
CA150 Installation Guide. xp_Layout 1 2019-03-26 1:52 PM Page 1

dormakaba USA Inc. System User Guide 7040.0321 | 1
Table of Contents
1 Introduction............................................................................................... 5
1.1 Approved Standards .........................................................................................................................5
1.1.1 705 Keypad FCC & IC Info..................................................................................................................... 5
1.2 Electrical Precautions........................................................................................................................5
1.3 Tools..................................................................................................................................................6
2 Typical System Layout (Single & Multi)..................................................... 7
2.1 Safe Lock Hardware..........................................................................................................................8
2.2 System Components.........................................................................................................................8
2.2.1 Keypad.................................................................................................................................................... 8
2.2.2 Multiplexer .............................................................................................................................................. 8
2.2.3 Safe Lock................................................................................................................................................ 8
2.2.4 AC Adapter............................................................................................................................................. 8
2.2.5 Battery Box............................................................................................................................................. 8
2.2.6 Alarm Box............................................................................................................................................... 8
2.2.7 Reset Box............................................................................................................................................... 8
2.2.8 Fob.......................................................................................................................................................... 9
2.2.9 Power Considerations ............................................................................................................................ 9
2.3 Getting Started..................................................................................................................................9
3 How to Use the System .......................................................................... 10
3.1 Keypad Model Definitions...............................................................................................................10
3.2 Menu Settings .................................................................................................................................12
3.2.1 Menu Settings –Display Keypad.........................................................................................................12
3.2.2 Menu Settings –Non-Display Keypad................................................................................................. 14
3.3 Install and Open a Lock..................................................................................................................14
3.3.1 Install (Electronically Pair) Lock and OLED Display Keypad............................................................... 14
3.3.2 Install (Electronically Pair) Lock and non-Display Keypad..................................................................14
3.3.3 Open a Lock –Display Keypad............................................................................................................ 14
3.3.4 Open a Lock –Non-Display Keypad....................................................................................................15
3.3.5 Open a Lock –Remote Disable........................................................................................................... 15
3.4 Reinstall Keypad .............................................................................................................................15
3.5 Change Combination ......................................................................................................................15
3.5.1 Change Combination –Display Keypad..............................................................................................15
3.5.2 Change Combination –Non-Display Keypad...................................................................................... 16
3.6 Change Time/Date/DST..................................................................................................................16
3.6.1 Change Time/Date/DST –Display Keypad..........................................................................................16

dormakaba USA Inc. System User Guide 7040.0321 | 2
3.6.2 Change Time/Date/DST –Non-Display Keypad..................................................................................16
3.7 Assign Time Lock Schedules..........................................................................................................17
(704 & 705 Models Only) ......................................................................................................................17
3.8 Users ...............................................................................................................................................17
3.8.1 Lock User Types................................................................................................................................... 17
3.8.1.1 Master..............................................................................................................................................................17
3.8.1.2 Manager...........................................................................................................................................................17
3.8.1.3 Other Users .....................................................................................................................................................18
3.8.1.4 User Capability –Access Lock........................................................................................................................18
3.8.1.5 User Capability –Audit Lock...........................................................................................................................18
3.8.1.6 User Capability –Time Delay Override with Combination..............................................................................18
3.8.1.7 User Capability –Time Delay Override with Fob Credential...........................................................................18
3.8.2 Add User............................................................................................................................................... 21
3.8.2.1 Add User –Display Keypad ............................................................................................................................21
3.8.2.2 Add User –Non-Display Keypad.....................................................................................................................21
3.8.3 Edit User............................................................................................................................................... 21
3.8.3.1 Edit User –Display Keypad.............................................................................................................................21
3.8.3.2 Edit User –Non-Display Keypad.....................................................................................................................22
3.8.4 Delete User...........................................................................................................................................22
3.8.4.1 Delete User –Display Keypad ........................................................................................................................22
3.8.4.2 Delete User –Non-Display Keypad ................................................................................................................22
3.9 System Functions............................................................................................................................23
3.9.1 System Info (Display Only)...................................................................................................................24
3.9.2 Backlight Mode..................................................................................................................................... 24
3.9.2.1 Backlight Mode –Display Keypad...................................................................................................................24
3.9.2.2 Backlight Mode –Non-Display Keypad...........................................................................................................24
3.9.3 Buzzer Mode.........................................................................................................................................24
3.9.3.1 Buzzer Mode –Display Keypad......................................................................................................................24
3.9.3.2 Buzzer Mode –Non-Display Keypad ..............................................................................................................24
3.9.4 Combination Length .............................................................................................................................25
3.9.4.1 Combo Length –Display Keypad....................................................................................................................25
3.9.4.2 Combo Length –Non-Display Keypad............................................................................................................25
3.9.5 User Mode............................................................................................................................................25
3.9.5.1 User Mode –Display Keypad..........................................................................................................................25
3.9.5.2 User Mode –Non-Display Keypad..................................................................................................................26
3.9.6 Credential Mode (705 Model Only)......................................................................................................26
3.9.7 Duress Mode (Silent Alarm)................................................................................................................. 26
3.9.7.1 Duress Mode –Display Keypad......................................................................................................................26
3.9.7.2 Duress Mode –Non-Display Keypad..............................................................................................................27
3.10 Locks .............................................................................................................................................27
3.10.1 Install a Lock....................................................................................................................................... 27

dormakaba USA Inc. System User Guide 7040.0321 | 3
3.10.2 Uninstall a Lock.................................................................................................................................. 27
3.10.2.1 Uninstall a Lock –Display Keypad................................................................................................................27
3.10.2.2 Uninstall a Lock –Non-Display Keypad........................................................................................................27
3.10.3 Reset a Lock....................................................................................................................................... 27
3.10.3.1 Master Reset.................................................................................................................................................28
3.10.3.2 Mechanical Reset..........................................................................................................................................28
3.11 Time Delay ....................................................................................................................................28
3.11.1 Enable/Disable Time Delay................................................................................................................ 28
3.11.1.1 Enable/Disable Time Delay –Display Keypad..............................................................................................28
3.11.1.2 Time Delay Count Mode –Display Keypad ..................................................................................................29
3.11.1.3 Enable/Disable Time Delay –Non-Display Keypad......................................................................................29
3.11.2 Open a Lock During Time Delay........................................................................................................ 30
3.11.2.1 Open a Lock During Time Delay –Display Keypad......................................................................................30
3.11.2.2 Open a Lock During Time Delay –Non-Display Keypad..............................................................................30
3.11.3 Cancel a Time Delay..........................................................................................................................30
3.11.3.1 Cancel a Time Delay –Display Keypad........................................................................................................30
3.11.3.2 Cancel a Time Delay –Non-Display Keypad................................................................................................30
3.11.4 Time Delay Override...........................................................................................................................31
3.11.4.1 Allow Time Delay Override –Display Keypad ..............................................................................................31
3.11.4.2 Allow Time Delay Override –Non-Display Keypad.......................................................................................31
3.11.5 Open Lock During Time Delay Using Override with Combo ............................................................. 31
3.11.5.1 Open Lock During Time Delay Using Override with Combo –Display Keypad ...........................................31
3.11.5.2 Open Lock During Time Delay Using Override with Combo –Non-Display Keypad ...................................32
3.11.6 Open Lock During Time Delay Using Override with FOB .................................................................32
3.12 Battery Levels................................................................................................................................33
3.12.1 Low Battery Warning.......................................................................................................................... 33
3.12.1.1 Low Battery Warning –Display Keypad........................................................................................................33
3.12.1.2 Low Battery Warning –Non-Display Keypad................................................................................................33
3.12.2 Critical Low Battery Warning..............................................................................................................33
3.12.2.1 Critical Low Battery Warning –Display Keypad............................................................................................33
3.12.2.2 Critical Low Battery Warning –Non-Display Keypad....................................................................................34
3.12.3 Replacing Batteries in Critical Low Battery State .............................................................................. 34
3.13 Wrong Try Penalty ........................................................................................................................34
3.14 View Audits (Display Only)............................................................................................................34
4 System Security...................................................................................... 35
4.1 Data Encryption...............................................................................................................................35
4.2 Initial Combination Handling...........................................................................................................35
5 LA GARD Software................................................................................. 36
5.1 Adding a User..................................................................................................................................36
5.2 Install a User into the Keypad.........................................................................................................36

dormakaba USA Inc. System User Guide 7040.0321 | 4
5.3 Firmware Update.............................................................................................................................37
5.4 Retrieve Audits................................................................................................................................37
5.5 Add Time Lock Schedules..............................................................................................................38
Appendix A: # Commands......................................................................... 39
Appendix B: List of Audits.......................................................................... 42

dormakaba USA Inc. System User Guide 7040.0321 | 5
1 Introduction
This guide outlines general information for using and programming LA GARD electric combination safe locks and all its
components, including accessories and software client. This guide assumes the installer has knowledge of electrical,
mechanical, and computer concepts, as well as having familiarity with safe lock systems and associated components. For
reliable and safe operation of the equipment, comply with all safety precautions outlined in this guide.
1.1 Approved Standards
The LA GARD family of safe locks conform to the following approved standards:
•UL 2058 (High Security Electronic Locks)
•EN 1300:2018 *Pending
•705 Keypad –FCC ID: 2ASNP-705, IC ID: 24793-705
•DKLG70X FOB –FCC ID: 2ASNP-DKLG70X, IC ID: 24793-DKLG70X
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna
•Increase the separation between the equipment and receiver
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
•Consult the dealer or an experienced radio/TV technician for help
CET APPAREIL EST CONFORME À LA NORME RSS INDUSTRIE CANADA EXEMPT DE LICENCE. Son
fonctionnement est soumis aux deux conditions suivantes:(1) Cet appareil ne doit pas provoquer d’interférenceset(2) Cet
appareil doit accepter toute interférence, y compris les interferences pouvant causer un mauvais fonctionnement du
dispositif. Cet appareil numérique de la classe [B] respecte toutes les exigences du Réglement sur le matériel brouilleur
du Canada.
1.1.1 705 Keypad FCC & IC Info
Follow these steps to view the FCC & IC information on a 705 Keypad:
1. Enter the ID and Combination to access the menu.
2. Navigate through the Main Menu and select System.
3. Select FCC Label from the sub-menu.
4. Navigate through the FCC & IC information on screen with the arrow buttons.
1.2 Electrical Precautions
Ensure alkaline batteries (where applicable) are new and in good condition; leaking batteries can cause damage to
components and can also cause serious bodily harm. Do not apply power (where applicable) before completing all steps
of the installation; doing so may damage the components. Ensure all power supplies are plugged into grounded electrical
receptacles that comply with local building code(s). When AC mains power is required the power supply shall be installed
in accordance with NFPA 70 and any applicable electrical codes.

dormakaba USA Inc. System User Guide 7040.0321 | 6
1.3 Tools
dormakaba USA Inc. recommends having the following tools on hand to install LA GARD safe locks and their
components:
•Digital voltmeter
•Wire cutters and needle nose pliers
•Set of screwdrivers
•Drill and drill bits
•Automatic saw (band saw, hand saw)
•US or Metric taps
•File or equivalent tool
•All installation/hardware documentation for quick reference

dormakaba USA Inc. System User Guide 7040.0321 | 7
2 Typical System Layout (Single & Multi)
The following sub-sections review safe lock system components with related diagrams. Refer to each product’s individual
documentation for more detailed information on hardware installation and proper device usage.
The following diagrams (Figures 1 and 2) show completed system layouts for both single and multi-lock systems. Please
note that your system may not include all components shown.
Figure 1 –Single Lock System
Battery box, alarm
box, or AC adaptor
LA GARD Prgm Cable
LA GARD Keypad
Figure 2 –Multi-Lock System
Battery box, alarm
box, or AC adaptor
LA GARD Prgm Cable
LA GARD Keypad
Lock #1
Multiplexor

dormakaba USA Inc. System User Guide 7040.0321 | 8
2.1 Safe Lock Hardware
Consult each component’s individual documentation for proper mounting, connectivity and installation. The safe itself
must be appropriate for the lock hardware to provide maximum security; certain makes and models of safes may not be
appropriate for this LA GARD safe lock system. If unsure, consult with dormakaba USA Inc. Sales or Support for further
information.
2.2 System Components
Each system may differ depending on customer requirements. The sub-sections outlined below cover the full suite of the
LA GARD safe lock system.
2.2.1 Keypad
The Keypad comes in two varieties: Display and non-Display. The Display variant shows messages on screen while the
non-Display version implements a series of LED flashes and beeps for messages. The Keypad is the user interface for
the entire system. Refer to the Keypad Installation Guide (Document #7033.0320) for more information.
2.2.2 Multiplexer
The Multiplexer is used in multi-lock systems and allows multiple safe locks to connect with the Keypad. Refer to the
Multiplexer Installation Guide (Document #7038.0320) for more information. The Multiplexer is not UL evaluated.
2.2.3 Safe Lock
The safe lock is either a dead bolt, a spring bolt or a swing bolt, that locks and unlocks when the Keypad receives correct
user credentials. This lock system comes in many varieties depending on the application. Refer to the Safe Lock
Installation Guide (Document #7034.0320) for more information.
2.2.4 AC Adapter
The AC Adapter can be used to power the System where batteries alone would not be appropriate. Refer to the AC
Adapter Installation Guide (Document #7037.0320) for more information.
2.2.5 Battery Box
The Battery Box can serve as the secondary power source to the LA GARD System. Refer to the Battery Box Installation
Guide (Document #7035.0320) for more information. The Battery Box is not UL evaluated.
2.2.6 Alarm Box
The Alarm Box is a hard-wired external alarm device. If used, the Alarm Box must be plugged into the BAT port of Lock
#1. The Alarm Box allows for a remote disable input that can block the open command to the lock if asserted. Refer to the
Alarm Box Installation Guide (Document #7036.0320) for more information. The Alarm Box is not UL evaluated.
2.2.7 Reset Box
The Reset Box, when attached to a lock BAT port will remove users and resets the Master Combination on LA GARD safe
locks. The lock being reset should be disconnected from the Keypad and must power up from a battery within the Reset
Box. The Reset Box LED will light when the reset function is performed. If a lock is already reset, applying the Reset Box
will not light the LED.
The Reset Box will only work in conjunction with LA GARD safe locks with a BAT port (will not work with older model LG
BASIC Series locks). Refer to the Reset Box User Guide (Document #7039.0320) for more information. The Reset Box is
not UL evaluated.

dormakaba USA Inc. System User Guide 7040.0321 | 9
2.2.8 Fob
The Fob is used as a secondary Bluetooth® credential to user’s combination. The fob can be enrolled at the Model 700
Keypad and assigned to a user.
For UL 2058 compliance, the fob credential was not evaluated by UL. However, if a fob credential is employed, it’s
required to be accompanied by a user combination to open a lock. The fob cannot be used as sole means to operate and
open the lock.
2.2.9 Power Considerations
The system common power across all components. As long as 9V DC power is supplied to the system, the system will
work as intended. It is unnecessary to apply multiple sources of power to some or all components.
Some considerations to follow:
•In the normal-profile Keypad, 2.9V batteries can be inserted into the tray
•In the low-profile Keypad, there is a connection for an emergency battery connection for application outside of the
safe container
•A LA GARD 700 Series Battery Box accessory is available to be attached inside the secure container to grant power
to the system
•A LA GARD 700 Series Alarm Box can be connected to the primary lock to provide power to the system. This Alarm
Box must be physically located in the secure side of the container
•A LA GARD 700 Series AC/DC Power Adaptor accessory can be used to apply line power to the system. The power
adapter can be connected to any lock’s BAT port in a multi-lock configuration
•In multi-lock installations while using a Multiplexer, it is strongly recommended that the AC/DC Power Adaptor be
used
•When resetting a lock via the LA GARD Series 700 Reset Box, a 9V battery must be inserted into the Reset Box to
apply power for the short duration usage
2.3 Getting Started
This section outlines typical use of a System with a single or multi-lock/single or multi-user setup with references to
various sections found through this document.
Follow these steps to get started implementing a System:
1. Review Section 2.2 System Components for installation procedures regarding each component of a System. For
single lock Systems, the use of a Multiplexer is not required.
2. Review section 3.9 Locks for information on installing, uninstalling and resetting safe locks.
3. Read section 3.7.2 Add User to add all non-Master users, including Managers.
4. Read section 3.2 Open a Lock for instructions on how to use the System once all pieces are connected.

dormakaba USA Inc. System User Guide 7040.0321 | 10
3 How to Use the System
This section outlines how to use the installed system and how to execute specified functions. Please note that your
instillation may not include everything outlined in this section.
3.1 Keypad Model Definitions
Model 701
Model 702
Model 703
Model 704
Model 705
OLED Display
Keypad
No
No
1.28”
Monochrome
OLED Display,
128 x 64
1.28”
Monochrome
OLED Display,
128 x 64
1.28” Monochrome
OLED Display, 128
x 64
Compatible Lock
Types
Swing/
Dead/
Spring Bolt
Swing/
Dead/
Spring Bolt
Swing/
Dead/
Spring Bolt
Swing/
Dead/
Spring Bolt
Swing/
Dead/
Spring Bolt
# of Users
1 Master/1
Manager/1
User
1 Master/1
Manager/2
8 Users
1 Master/1
Manager/28
Users
1 Master/1
Manager/47
Users
1 Master/1
Manager/97 Users
# of Locks
1
1
2
5
5
Dual-User Mode
No
Yes
Yes
Yes
Yes
Reset Function
Yes
Yes
Yes
Yes
Yes
Time Delay
No
0-99 Min.
0-99 Min.
0-99 Min.
0-99 Min.
Confirmation
Window
No
1-60 Min.
1-60 Min.
1-60 Min.
1-60 Min.
Time Delay
Override (TDO)
No
Yes
Yes
Yes
Yes
TDO with BLE
Key Fob
No
No
No
No
Yes
Programmable
at Keypad
Yes
Yes
Yes
Yes
Yes

dormakaba USA Inc. System User Guide 7040.0321 | 11
Model 701
Model 702
Model 703
Model 704
Model 705
Programmable
by PC
No
Yes
Yes
Yes
Yes
Audit Events
No
500
500
2000
6000
View Audit Trail
No
No
Yes
Yes
Yes
Downloadable
Audit Trail
No
Yes
Yes
Yes
Yes
Duress Alarm
No
Yes
Yes
Yes
Yes
Combination
Length
11
(2id + 6-9)
11
(2id + 6-9)
11
(2id + 6-9)
11
(2id + 6-9)
11
(2id + 6-9)
Back Lit Keypad
No
Yes
Yes
Yes
Yes
Bolt Switch
Option*
No
Yes
Yes
Yes
Yes
Wrong Try
Penalty
Yes
Yes
Yes
Yes
Yes
Batter Power
2 x 9V
2 x 9V
2 x 9V
2 x 9V
2 x 9V
Low-Profile
Option
No
Yes
Yes
Yes
No
AC Power
Option*
Yes
Yes
Yes
Yes
Yes
VdS 2396 –
Class 2
Pending
Pending
Pending
Pending
Pending
UL 2058 –UL
Type 1
Yes
Yes
Yes
Yes
Yes
EN1300 –Level
B
Pending
Pending
Pending
Pending
Pending
SBSC –3880-
2015
Pending
Pending
Pending
Pending
Pending

dormakaba USA Inc. System User Guide 7040.0321 | 12
Model 701
Model 702
Model 703
Model 704
Model 705
CNPP q2p –
Level B/E
Pending
Pending
Pending
Pending
Pending
Time Lock
Schedule
No
No
No
Yes
Yes
Dual Credential
No
No
No
No
Yes
Warranty
2yr
from DoM
2yr
from DoM
2yr from DoM
2yr from DoM
2yr from DoM
Extended
Warranty*
Yes
Yes
Yes
Yes
Yes
Updatable
Firmware
Yes
Yes
Yes
Yes
Yes
*Sold separately
3.2 Menu Settings
3.2.1 Menu Settings –Display Keypad
To enter the Main Menu, press any non-numeric button followed by your user credentials.
Below is a list of buttons and their functions on the Keypad:
•Number Pad –Can be used for entering User combinations, # commands (for non-Display Entries) and specific
optional functions on screen (for Display Entries)
•Pound Key (#) –Is used to return to a previous screen, or to wake up the Keypad without entering a number
•Up and Down Arrows (˄˅) – Navigate through options with these (for Display Entries)
•Return Key (←) – Confirms a selection or completed a key sequence
Below is a table outlining each Menu Setting and sub-setting within the Keypad display interface. Note that the menu
available changes based on the User Privileges.
Table 1 –Menu Settings (Display Keypad)
Open Lock
Allows the User to open a lock.
Change combo
New Combo
Allows the User to change their combination.
Time/Date
Time Format
Choose between a 12 and 24HR time format.
Date Format
Change the date format.
Set Time Date
Change the time and date.
Observe DST
Select Enable/Disable to observe Daylight Saving Time
(DST).

dormakaba USA Inc. System User Guide 7040.0321 | 13
Time Lock
Assign Access
Designate a lock as 24/7 or assign one of two schedules.
View Access 1
View the access of schedule #1.
View Access 2
View the access of schedule #2.
View Holiday
View the assigned holidays.
Audits*
Displays transactional data from a lock.
PC Link*
Connects the Keypad to a PC running the LA GARD
software client.
Users
Add
Add a User based on their User ID.
Edit
Edit a User based on their User ID.
Delete
Delete a User based on their User ID.
System
Sys Info
Keypad
Displays Battery Status, Firmware version, Model and Serial
#s.
Lock
Shows firmware versions, serial numbers, port & Lock # and
Open Count.
Backlight
Toggle the Backlight On and Off.
Buzzer
Toggle the Buzzer sound On and Off.
TD Cnt Mode
Set counting period to count up, down or not show time in
the periods.
Combo Length
Determines the length of a combination.
User Mode
Choose between Single, Dual and Dual + Mgr.
Cred Mode
Choose between Single, Dual and Dual + Mgr.
Duress Mode*
Enables/Disables Duress Mode (Silent Alarm).
Locks
Choose between Install, Uninstall, TL Schedule, Time Delay
configuration times, Time Delay Override allowed and
Reset.
FW Update
Enables a firmware update when connected to a PC running
the LA GARD software client.
FCC Label
Display the FCC label information.
*Not evaluated by UL

dormakaba USA Inc. System User Guide 7040.0321 | 14
3.2.2 Menu Settings –Non-Display Keypad
Below is a table outlining each # Command and their function for non-display entries. See Appendix A for complete
definitions.
Table 2 –# Commands (non-Display Keypad)
*Not
evaluated by UL
3.3 Install and Open a Lock
3.3.1 Install (Electronically Pair) Lock and OLED Display Keypad
Follow these steps to “INSTALL” (logically, electronically pair) a safe lock to an OLED Display Keypad:
1. Press any button to Open factory setting Menu
2. Press <rtn key> to test the opening of the lock, OR
3. Press <down> to highlight INSTALL LOCK
4. Press <rtn key>
5. Enter Master ID + default combination [00 12345678]
6. If this is the Primary Lock in a system of multiple locks, scroll to “YES”, then
7. Press <rtn key>
8. Message appears –“Success Lock Installed”
3.3.2 Install (Electronically Pair) Lock and non-Display Keypad
Follow these steps to “INSTALL” (logically, electronically pair) a safe lock to a non-OLED Display Keypad:
1. Push any key to wake up the system in factory mode –it will beep and display the red function indicator
light for 10 seconds. While the red LED is illuminated, the system is awake, and the “1” key will open the
lock or the keypad is ready process “#” set-up commands.
2. With the system awake, enter #22 Master ID+combination 00 12345678 <rtn key>
3. The lock is now Installed (paired with the keypad).
4. Once “Installed”, there is no need to “wake up” the system before another intended key sequence.
3.3.3 Open a Lock –Display Keypad
Follow these steps to open a safe lock on a Display Keypad:
1. Enter the User ID.
Set Combo Length
#11
Reinstall Keypad
#32
Delete User
#56
Set User Mode
#12
Set Backlight On/Off
#40
Reset User Combo
#57
Set Duress
(Silent Alarm)
#14
Set Buzzer On/Off
#41
Set Time/Date
#65
Install Lock
#22
Add User
#50
Set TD/OW Values for
Lock #1
#72
Uninstall Lock
#23
Change Own Combo
#52
Set TDO Allowance for
Lock #1
#73
Reset Keypad
#25
User Enable/Disable
#54
Cancel Time Delay
#74
Open PC Link*
#30
Set User Lock Privileges
#55
Enable FW Update
#99

dormakaba USA Inc. System User Guide 7040.0321 | 15
2. Enter the User Combination.
3. If required, present and click the button on the user fob when requested.
4. If required, enter User #2 credentials.
5. If this is the user’s first time opening a lock, the Keypad display interface will ask the User to change their original
combination. Input a new combination with the keypad. Re-enter the same combination to confirm.
Note: The new Combination must be different from the old Combination. The User is advised to use a non-trivial
combination.
6. The lock’s latch will open and the screen will display Lock Open. After 3 seconds, the lock’s latch will close.
If Time Delay is in effect, menus will be different. Consult the Time Delay section in this document for more information.
3.3.4 Open a Lock –Non-Display Keypad
Follow these steps to open a safe lock on a non-Display Keypad:
1. Enter the User ID and Combination.
2. If this is the User’s first time opening a lock, the Keypad will require a new Combination. Using the Keypad keypad,
input #52 + Authorized User ID and Combination + User ID and new Combination + User ID and new Combination
again + Return Key.
3. The lock’s latch will open. After 3 seconds, the lock’s latch will close.
If Time Delay is in effect, the lock will not automatically open.
3.3.5 Open a Lock –Remote Disable
With the application of the Alarm Box, the opening sequence can be disabled by asserting a signal on the Alarm Box. The
signal may come from an external alarming system that could feed into this lock to prevent it from opening.
Please observe the following while using the Remote Disable:
•The Remote Disable assertion will not block users from accessing the menus on a Display Keypad
•The signal must be asserted prior to the user authentication for it to be recognized by the system
•Duress combinations will still trigger the alarm signal, even if Remote Disable is asserted
•An Keypad with a display will show ‘Lock #x NOT open’ when the Remove Disable is asserted. The ‘x’ would be
replaced by a lock that is targeted to be opened
3.4 Reinstall Keypad
A new Keypad can be installed into the system if the current one is defective or needs to be replaced. If the new Keypad
is a non-Display screen variant, a command sequence would need to be followed with an authorized user. If the Keypad
has a display screen, prompts will appear to guide the user through the process. An Audit will be generated to indicate
which user installed the new Keypad. Once paired, the system returns to regular operation. Refer to the Keypad
Installation Guide (Document #7033.0320) for more information.
Note: The system will only recognize the same Keypad model as before, otherwise it will reject the reinstall process. If
installing a new model of Keypad, all locks attached to the system must be reset/uninstalled and reinstalled prior to
installing the new Keypad.
3.5 Change Combination
3.5.1 Change Combination –Display Keypad
Follow these steps to change a User combination on a Display Keypad:
1. From the Keypad display Main Menu, select Change combo.
2. New Combo appears on screen. Input a new combination with the number pad.

dormakaba USA Inc. System User Guide 7040.0321 | 16
Note: The new Combination must be different from the old Combination. The User is advised to use a non-trivial
combination.
3. Confirm appears on screen. Input the same combination from the previous step to confirm. Success will appear on
screen. The new combination is set and will be in affect the next time the User enters their combination. The
Keypad will beep three times with a green LED and return to the Enter ID menu once complete.
3.5.2 Change Combination –Non-Display Keypad
Follow these steps to change a User Combination on a non-Display Keypad:
1. If a Master/Manager User is changing another User’s combination, do the following:
a. Using the Keypad, input #57 + Authorized User ID and Combination + User ID and new Combination +
User ID and new Combination again + Return Key.
b. The Keypad will beep three times and flash a green LED
2. If a User is changing their own combination, do the following:
a. Using the Keypad, input #52 + User ID and Combination + User ID and new Combination + User ID and
new Combination again + Return Key.
b. The Keypad will beep three times and flash a green LED once complete
3.6 Change Time/Date/DST
3.6.1 Change Time/Date/DST –Display Keypad
Follow these steps to change the Time/Date/DST on a Display Keypad:
1. Navigate through the Main Menu and select Time/Date.
2. Select one of the follow sub-menu options:
a. Time Format –Choose between 24Hr and 12Hr
b. Date Format –Choose between yy_mm_dd, mm_dd_yy, and dd_mm_yy
c. Set Time Date –Input the time and date with the number pad
d. Observe DST –Select either Enable or Disable
3. The Keypad will beep three times and flash a green LED once complete.
To effectively use the DST settings, the DST tables must be sent down from the PC software when setting time via the
PC. If the Time/Date is not set after a prolonged power outage, access time lock schedules cannot be enforced and may
result in the inability to open the lock until the Time/Date is set.
3.6.2 Change Time/Date/DST –Non-Display Keypad
Follow these steps to change the Time/Date/DST on a non-display Keypad:
Note: Model 701 does not allow for the time to be set.
1. To change the Time/Date, using the Keypad, input #65 + Authorized User ID and Combination + 10-digit Time Date
(YY-MM-DD-24HR Clock) + Return Key.
2. To change DST, using the Keypad, input #63 + Authorized User ID and Combination + Enable DST (1) or Disable
DST (0) + Return Key.
3. The Keypad will beep three times and flash a green LED once complete.

dormakaba USA Inc. System User Guide 7040.0321 | 17
3.7 Assign Time Lock Schedules
(704 & 705 Models Only)
This section outlines how to assign pre-loaded Schedules and view pre-loaded Holidays from the Keypad. To load specific
dates and times to Schedules and Holidays from the PC software. Refer to section 5.5 Add Time Lock Schedules for more
information.
The Time Lock feature can restrict access to a safe lock at specific times during the week or allow access for an entire
day, a day spans midnight to midnight of the next day.
Follow these steps to create time access periods from a week per lock or view Holiday lockout day(s):
1. Navigate through the Main Menu and select Time Lock.
2. To Assign Access, do the following:
a. Select Assign Access
b. For multi-lock Systems, select the lock by pressing the corresponding number on the number pad.
Otherwise, skip to the next step
c. Choose between 24/7 Access or a pre-loaded Schedule
3. To View Access, do the following:
a. Select View Access
b. Navigate through the information on screen with the arrow buttons
4. During a Holiday, the lock will not open at any time on the specified day(s). To view holiday(s), do the following:
a. Select View Holiday
b. Navigate through the information on screen with the arrow buttons
Note: If Time/Date is not set after a prolonged power outage, access time lock schedules cannot be enforced and may
result in the inability to open the lock until the time/date is set.
3.8 Users
3.8.1 Lock User Types
There are three types of users, each with different capabilities. The sub-sections outlined below cover each Lock User
Type and their respective functions.
3.8.1.1 Master
•There will always be 1 Master User per safe lock
•Combination length is always 8 digits and is not modified by the combination length system setting
•The default factory combination is 1-2-3-4-5-6-7-8
•The User ID is always 00 and cannot change
•Cannot open the lock directly
•Can change their combination either via the Keypad or the LA GARD Software client
•Needs to authenticate with an old combination prior to being allowed to update their combination
•The forced-change-on-first-use rule does not apply to Master combinations
•The Master combination should be changed from the default value prior to adding any other non-Master Users to
the System
3.8.1.2 Manager
•Should be enabled within the system, but not required

dormakaba USA Inc. System User Guide 7040.0321 | 18
•Multiple Managers may be defined depending on the lock type
•Only Master-authenticated users can modify the Manager’s settings
•The combination is in the format of 2 ID digits plus 6 to 9 combination digits
•The combination length required for the system applies to Manager(s) and all other users
•The combination length will be the same for all Users in the system, including Manager(s)
•May change their combination via the Keypad
•May open the lock if the access settings are enabled for the lock
•May set other access Users’ one-time-combo via the Keypad menus or via the LA GARD Software client
•May be granted Time Delay Override if Time Delay option is applied to a safe lock
3.8.1.3 Other Users
•The combination is in the format of 2 ID digits plus 6 to 9 combination digits
•In a multi-lock installation, the User may be enabled for some locks and disabled for others
•All User settings apply to all locks in a multi-lock configuration
•Users can be configured to have one or more capabilities
3.8.1.4 User Capability –Access Lock
A user may be allowed to open the lock. This capability allows the user to open the lock when they present proper
credential(s). Each access user may be granted individually the ability to bypass the time delay, if time delay is
configured. If the system is in Dual User Mode, either user with this option will cause the time delay to be bypassed.
3.8.1.5 User Capability –Audit Lock
A user can be given the capability to retrieve audits via a software application (authenticated via the ID and combo) or for
review at the Keypad via the menus. A user identified as one that can collect audits can retrieve audits from any lock that
they have access to via the software connected to the Keypad (and lock), or manually via the Keypad menus.
3.8.1.6 User Capability –Time Delay Override with Combination
This capability allows the user to override the time delay, if enabled for the user, with their combination and open the lock
without waiting for the time delay period to expire. They may or may not need a key fob for the second credential if
required for Model 705.
3.8.1.7 User Capability –Time Delay Override with Fob Credential
This capability allows the user to override the Time Delay with their assigned fob credential, but they may not open the
lock.
The Table below shows the permitted mix of capabilities a user may perform. The configuration software and lock
firmware shall enforce this capability mix.
Table 3 –User Capabilities
TDO
w/FOB
TDO
w/Combo
Audits
Access
Notes
1
0
0
0
User can Override Time Delay only.
May not open the lock nor retrieve
audits. The user must present the FOB
during an open sequence initiated by an
authorized user(s).
0
0
1
0
User may retrieve audits only. May not
open the lock.
0
0
0
1
User may open the lock only.

dormakaba USA Inc. System User Guide 7040.0321 | 19
0
0
1
1
User may open the lock and retrieve
audits.
0
1
0
1
User may open the lock and override
the Time Delay with their credential(s).
0
1
1
1
User may open the lock, retrieve audits
and override Time Delay with their
credential(s).
Table 4 –System User Functions
Functions
Master
Manager
Access
User
Audit
User
TDO
Fob
User
Install Lock
x
Uninstall Lock
x
Reinstall Keypad
x
x
x
Configure Time Lock Access Schedule
x
x
View Time Lock Access Schedule on Keypad
x
x
Configure Time Lock Holiday Schedule
x
x
View Time Lock Holiday Schedules on Keypad
x
x
Set Time Format
x
Set Date Format
x
Daylight Saving Time (DST) Enable/Disable
x
x
Set Date/Time
x
x
View Audits on Keypad
x
x
x
Retrieve Audits to PC
x
x
x
Activate PC Link
x
x
x
Assign Time Lock Access Schedule
x
x
Enable/Disable Dual User Mode
x
Enable/Disable Dual User Mode Applies to
Managers
x