Doro 80 User manual

   
doro 80
Manual

9
7
8
1
2
3
5
4
6

1
Talk button
2
OK/Menu button
3
*
and Scroll up button
4
Speed Dial button
5
Redial button
6
Channel change button
7
Recall button
8
#
and Scroll down button
9
Erase button

English
4
www.doro.com
Index
Installation
5
Unpacking
...........................
5
Connection
.........................
5
Belt clip
...............................
6
Battery
................................
6
Battery charge indicator
.....
7
Range
.................................
7
Headset
..............................
7
Operation
8
Making a call
.......................
8
Receiving a call
..................
8
Redial function
....................
8
Recall
..................................
8
Volume control
....................
9
Timer
...................................
9
Paging
.................................
9
Phone Book
........................
9
Caller Identi cation
10
Menu System
......................
10
Handset Settings
11
Ringer volume
....................
11
Auto Answer
.......................
11
Contrast
..............................
11
Date/time
............................
11
Other
12
Troubleshooting
..................
12
Speci c Absorption Rate
(SAR)
..................................
13
Guarantee
...........................
14

English
www.doro.com 5
Installation
Unpacking
The package contains:
- Handset
- Mains adapter
- Base unit
- Line cord
- NiMH Battery pack
- Belt clip
Connection
1.
Connect the mains adapter to the socket on the base unit and to an electrical
wall socket.
2.
Insert the battery plug ensuring correct polarity is observed and  t the
battery into the handset. Carefully  t the battery cover.
3.
Place the handset in the base unit, with the keypad facing outwards.
Once
the handset is correctly positioned in the base unit, a beep will be heard.
4.
Charge the handset battery without interruption for 24 hours before initial
use. Thereafter fully discharged batteries will take 12 hours to recharge.
5.
ONCE CHARGED, connect the telephone line cord to the TEL LINE
socket on the base unit and to telephone network wall socket .
6.
The telephone is now ready for use.
Important notes!
Under mains power failure conditions this telephone will not work. Please ensure that a
separate telephone not dependent on local power is available for emergency use.
The earpiece of the handset may attract small ferromagnetic objects such as staples and pins,
care should be taken when placing the handset near such items.
Do not place the base unit close to other electrical equipment such as TV sets, computer screens,
telecom equipment, fans etc. This will minimise the risk of interference.
Do not place the base unit in areas of high humidity or where it will be exposed to direct
sunlight or other major heat sources.

English
6
www.doro.com
6 www.doro.com6
Installation
Belt clip
The supplied belt clip can be  tted to the back of the handset, allowing the
handset to be attached to a belt, shirt pocket or similar. To attach the clip, line
up the indents on either side of the handset and press into place over the back of
the handset.
Battery
The telephone is supplied with an environmentally-friendly nickel metal hydride
(NiMH) battery pack. As with all batteries, performance may degrade over time;
should you notice that talk and standby times have reduced considerably or there
are signs of leakage, the battery pack should be replaced.
Fully-charged batteries will last for approx. 10 hours in standby or approx. 6
hours’ call time. These operation times apply at normal room temperature using
a fully charged battery.
Completely discharged batteries will take about 12 hours to fully recharge.
Please note that the battery charge indicator in the handset display  ashes while
charging and will stop  ashing when the battery is fully charged. The indicator
on the base unit will stay lit as long as the handset is located in the base unit,
and will not go out when the battery is fully charged.
The base unit has an automatic charging mechanism that prevents the batteries
from being overcharged or damaged by prolonged charging.
Please note!
To ensure and maintain good charging of the handset batteries we recommend that the base and
handset charge contacts are cleaned regularly, ie monthly, with a pencil eraser and/or a soft
dry cloth. The recharging system used in this model may result in the handset and the batteries
becoming warm. This is normal and will not damage the equipment.
When the telephone is installed for the  rst time, the batteries must be charged for 24 hours
before using the telephone. Use DORO original batteries only. The guarantee does not cover
any damage caused by incorrect use of batteries. Please dispose of any batteries in a responsible
and environmentally friendly manner.

English
www.doro.com 7
Installation
Battery charge indicator
The
]
symbol in the display indicates when it is time to recharge the
batteries. When the battery is running low, a warning signal sounds. If the
handset is not recharged at this time, the phone will cease to function until it is
recharged.
Range
The range of the telephone varies depending on different factors in the
surrounding environment. Radio waves transmitting the call may be hindered
by obstructions or signal re ections that can reduce the range.
Speci ed ranges require unobstructed transmission between the handset and
the base unit. In such ideal conditions the telephones range can be up to 400
metres.
In densely populated areas, houses, apartments, etc. the range will be reduced.
Try to get the best range by relocating the base unit, the ideal location is a high
and unobstructed place. The range can be improved by turning your head so
that the handset is pointing towards the base unit.
If you carry the handset in close proximity to the range limit during a call, the
sound quality will decrease and the call may be disconnected
.
Headset
When using an optional headset, there is no change in the way a call is received
or made. When a headset is connected, the microphone and speaker on the
handset are automatically disconnected.
This telephone supports the use of the mute function with a button on the
headset cable.
Please note!
The earpiece volume may be very high on the headset. We recommend you immediately adjust
the earpiece volume when connecting an optional headset.

English
8
www.doro.com
8 www.doro.com8
Operation
Making a call
1.
Enter the required number. Mistakes can be corrected using
C
.
2.
Press
q
to dial the number.
3.
Press
q
again to terminate the call.
q again to terminate the call. q
Receiving a call
1.
When the telephone rings.
2.
Press
q
to answer the call.
q to answer the call. q
3.
Press
q
again to terminate the call.
q again to terminate the call. q
Please note!
You must press
q
to terminate any call; closing the  ip cover will not terminate a call.
If the telephone cannot connect to a line, a warning tone will be heard. The problem may be due to
the batteries running low, the handset being too far from the base unit or all of the transmission
channels being engaged.
If you experience strong interference during the call, this may be corrected by changing the operating
channel. Press the
button to scan the available operating channels for the best and clearest
operation.
Redial function
The most recently dialled number (up to 28 digits) can be easily redialled using
r
.
1.
Press
r
.
2.
Press
q
to dial the number.
Recall
Access to additional network services can be gained by using the recall button
R
.
For example Call Waiting: when the call waiting tones are heard press
R
, listen for
dial tone then press 2. Please note some networks require only the
R
button to be
pressed, please contact your network provider for further service information.
If this product is connected to a business PBX system, to transfer a call press the
recall button R followed by the extension number.

English
www.doro.com 9
Operation
Volume control
The volume may be adjusted during a call using the switch on the side of the
handset. You can select between Low, Mid and High settings
.
Timer
Immediately following the connection of a call, a call timer will be shown on
the display. The timer is a simple way to help you keep track of how long the call
lasts.
Paging
Pressing
J
on the base unit will activate the paging signal of the handset. This
function is used to help locate the handset or to page the person carrying the
handset. The signal will stop automatically after a while.
Phone Book
This telephone has 10 speed dial memory locations.
A stored phone number can be dialled using fewer keystrokes. The memory
locations are numbered 0-9.
Storing speed dial memory locations
1.
Enter telephone number (up to 14 digits). Use
C
to erase or change.
2.
Press
b
. The display will show STORE?
3.
Press
0
. The display will show ENTER LOCATION:
0
. The display will show ENTER LOCATION:
0
4.
Enter memory location,
0
-
9
.
Please note!
Press
r
if you need to insert a pause in the telephone number.
If you need to change a number, store the new number in the same location as the old one by
following the above instruction.
Dialling using speed dial memories
1.
Press
b
.
2.
Enter memory location,
0
-
9
.
3.
Press
q
to dial the number.
q to dial the number. q

English
10
www.doro.com
10 www.doro.com10
Caller Identi cation
Menu system
The telephone has  ve areas that are accessed with the
w
button. Each area is
described below.
Explanation of Caller ID
Caller ID allows you to see who is calling before you answer a call or to see who has
called in your absence.
The memory will store up to 56 telephone numbers.
When the log is full, the oldest number will be deleted automatically as the new call is
logged. New calls are indicated in standby mode by NEW in the display and the red
indicator
on the top edge of the handset  ashing.
! OLDEST and ! LATEST are displayed at the start and end of the call log.
Retrieving and dialling incoming numbers
1.
Press
w
.
2.
Scroll to CID LIST using
{
/
}
. Press
}
. Press
}
0
0
.
0
3.
Scroll to the required log entry using
{
/
}
}
.
}
4.
Press
q
to dial or press
q to dial or press q
w
to return to standby mode.
Important note!
New Zealand users: To insert the leading 0 of the area code at dial back, press
w
0
before pressing
q
q
.
q
In order for numbers to be shown, you must subscribe to the Caller ID service provided by your network
operator and have a current subscription in place. Contact your operator for more information.
Messages
Besides showing telephone numbers, the display may also show a number of messages.
UNAVAILABLE
It is an International call or a call from a PBX (no information
received).
WITHHELD
Information on the number is blocked. The call could also be from
a PBX.
Transferring numbers to memory
1.
Press
w
scroll to CID LIST using
{
/
}
. Press
}
. Press
}
0
0
.
0
2.
Press
b
. The display will show STORE?
3.
Press
0
. The display will show ENTER LOCATION:
0
. The display will show ENTER LOCATION:
0
4.
Enter memory location
0
-
9
. The display will show COMPLETED. and the
handset returns to standby mode.
Erasing Numbers
1.
Press
w
scroll to CID LIST using
{
/
}
. Press
}
. Press
}
0
0
.
0
2.
Scroll to the required log entry using
{
/
}
}
.
}
3.
Press and hold
C
until the display shows DELETE?
4.
Press
0
to con rm.
0 to con rm. 0