Doro CONGRESS 150 User manual

SENSOR 150
Telephone with calling number display
User guide

AUDIOLINE SENSOR 150 TABLE OF CONTENTS
TABLE OF CONTENTS
Installation ............. 1Calling Number Display .... 7
Location of controls ........ 1Explanation of CND ........... 7
Battery .................. 2New calls ................... 7
Connection .............. 2To view the new call information .. 8
Wall mounting ............ 2Caller display log full ........... 8
Warning ................. 3Dialling from the caller display log .9
The display .............. 3Erase caller display number ...... 9
Setting the date and time ..... 3
Using the telephone ..... 4Phone Book (Memories) ... 10
Ringer volume ............ 4Programming ................. 10
Select Language ........... 4Dialling from memory .......... 11
Handset On/Off ........... 4Erasing ..................... 11
Earpiece volume ........... 4 Answering incoming calls
5 .................. Settings 12 .................... To
make a call ................ 5 Least Cost Routing (LCR) ....... 12
Call timer ................ 5 Programming ................. 12
Last number redial ......... 5
Additional network services .. 5 Other ................. 13
Main Menu ............... 6 Troubleshooting ............ 13
Cleaning ................ 13
REN/RN .................. 13
Thunderstorm Warning ........ 14
Guarantee ................. 14

ABC
WXYZTUVPQRS
MNOJKLGHI
DEF
C
OK
MENU
4
9
10
11
12
2
3
5
6
7
1
8
1
INSTALLATION AUDIOLINE SENSOR 150
LOCATION OF CONTROLS
1Earpiece 7Scroll UP and * button
2Display 8Microphone
3Talk/OK button 9Scroll DOWN and # button
4Menu button 10 Recall button
5Last number redial 11 End call/Erase button
6Keypad 0-9 12 New call indicator

2
AUDIOLINE SENSOR 150 INSTALLATION
BATTERY
3x1.5 V batteries (AAA) must be installed, otherwise functions such as caller display,
memory etc will not work. When the batteries are low the symbol will illuminate on
the display.
PRemove the line cord before installing or replacing batteries.
PRemove the screw from the battery compartment on the rear of the handset. Fit the
batteries (supplied) observing correct polarity.
NOTE: For the telephone to operate correctly batteries must be installed. If no
batteries are installed the talk button must be pressed and held down for 1-2 seconds
to access the telephone line.
CONNECTION
PFit the batteries, as described above.
PConnect the line cord to a telephone wall socket.
WALL MOUNTING
The telephone can be placed on the desk or on the wall with the supplied wall bracket.
Check for hidden cables, water pipes, etc, before drilling holes, also ensure that the
intended mounting point is within reach of a telephone socket.
PUse the wall bracket provided to mark two holes (86 mm apart) on a wall, one above
the other.
PHold the wall bracket to the wall and secure with two screws (not supplied.)
WARNING The handset may retain small ferromagnetic objects, such as pins
and staples around the earpiece. To prevent injury, you should check for the
presence of these objects before use.

3
INSTALLATION AUDIOLINE SENSOR 150
THE DISPLAY
When the Sensor 150 is in standby mode, the 11 character/13 digit display will show the
current date and time, how many incoming calls are stored in the caller log, and if the
battery is low.
Text information
Incoming telephone number
Low battery
New call Number Time Date
indicator of calls
SETTING THE DATE AND TIME
PPress the MENU button. The display will show "VOLUME"
PPress the button repeatedly until the display shows "SETTING". Press OK.
PPress the button repeatedly until the display shows "SET TIME". Press OK.
PThe hour digit(s) will flash on the display. Use the buttons to set the
correct hour. Press OK to store the setting.
PSet the minute, day and month in the same way. Press OK after every setting.
PPress the Cbutton to store the setting and return to standby.

4
AUDIOLINE SENSOR 150 USING THE TELEPHONE
RINGER VOLUME
The ringer can be set to either high, low or off.
nPress the MENU button. The display will show "VOLUME".
nPress theor buttons until the display shows "SETTING". Press OK.
nThe display will show "RING". Press OK.
nThe display shows the current setting (2 = High, 1 = Low, 0 = Off).
nPress the or buttons to set the volume. Press OK.
SELECT LANGUAGE
The Sensor 150 can change the display texts language. The languages available are
English, German, French and Spanish.
nPress the MENU button. The display will show "VOLUME".
nPress the or buttons until the display show "SETTING". Press OK.
nPress the or buttons until the display show "LANGUAGE". Press OK.
nThe display will show the current setting.
nPress the or buttons to select the desired language. Press OK.
HANDSET ON/OFF
The Sensor 150 does not have a hook switch. Access to the telephone line is via two
buttons, TALK/OK and END CALL/C.
#Press the TALK/OK button you will hear dial tone.
#Press the END CALL/C button to terminate the call.
EARPIECE VOLUME
The earpiece volume can be set to two levels (1=low, 2=high).
nPress the MENU button. The display will show "VOLUME". Press OK.
nPress the or buttons to set the volume. Press OK.

5
USING THE TELEPHONE AUDIOLINE SENSOR 150
ANSWERING INCOMING CALLS
nTo answer an incoming call press the TALK/OK button
nPress the End Call button to terminate the call.
NOTE: For the telephone to operate correctly batteries must be installed. If batteries
are not installed the talk button must be pressed and held down for 1-2 seconds to
access the telephone line.
TO MAKE A CALL
nDial the telephone number you wish to call. If you enter an incorrect digit this can be
erased using the Cbutton.
#Press the TALK/OK button .
#Press the END CALL/C button to terminate the call.
Alternatively
#Press the TALK/OK and then dial the telephone number required.
#Press the END CALL/C button to terminate the call.
CALL TIMER
Afew seconds after a call has started, the call timer will display the elapsed time of the
call.
LAST NUMBER REDIAL
If the last number dialled was engaged or the call was not answered, it is possible to redial
the number using the Redial button .
nPress the last number Redial button .
nPress the TALK/OK button.
ADDITIONAL NETWORK SERVICES
Network services such as call waiting, call forward etc., can be accessed via the Recall
[R], #and *buttons. For further information, contact your Network Operator.

6
AUDIOLINE SENSOR 150 USING THE TELEPHONE
MAIN MENU
The Sensor 150 has a simple menu system which displays texts, this is accessed using
five buttons.
The MENU button is used to enter the menu system.
The and buttons are used to scroll through the menu system.
The OK button is used to confirm your choice.
The Cbutton is used to erase an incorrect entry.
THE MAIN MENU HAS FOUR HEADINGS:
VOLUME - Earpiece volume
You can select the earpiece volume required. See page 4 for more information.
CALLER ID - Calling Number Display
The incoming telephone numbers can be displayed and dialled. See pages 7-9 for more
information.
PHONE BOOK - Memories
Most frequently dialled telephone numbers/names can be stored into memory. See pages
10-11 for more information.
SETTING - Settings
All of the settings for the telephone ringer, language etc can be altered. See page 4 for
more information.

7
CALLING NUMBER DISPLAY AUDIOLINE SENSOR 150
EXPLANATION OF CALLING NUMBER DISPLAY
Calling Number Display allows you to see who is calling before you answer a call, and
also to see who called in your absence. When you have subscribed with your telephone
network service provider to the "Calling Number Display" service, the telephone number,
name (if the number is stored in the phonebook), date and time of your calls will be
displayed. Up to 15 numbers can be stored in the Sensor 150 call log.
It is not possible to view the call log and take a new call at the same time.
NOTE: Calling Number Display is an optional telephone Network service. This
telephone will provide Calling Number Display information provided the service is
available via your Network service provider and any subscription charges have been
paid. Check with your service provider for full details.
If the Calling Number Display service is not implemented on your telephone line,
incoming call information will not be displayed.
NEW CALLS
When a new call is received the new call indicator at the top of the telephone will flash,
the words "NEW CALLS" and the total number of new calls will be displayed.
Below is an example of four new numbers/calls, with a total of thirteen calls in the call log.

8
AUDIOLINE SENSOR 150 CALLING NUMBER DISPLAY
TO VIEW THE NEW CALL INFORMATION
nPress the MENU button. The display will show "VOLUME"
nPress the button until the display shows "CALLER ID". Press OK.
nPress the or to see the incoming telephone numbers.
nPress the MENU button to exit.
The button scrolls from the beginning of the call log, showing the oldest telephone
number first.
The button scrolls from the end of the call log, showing the newest telephone
number first.
The time & date when a call is received, the phone number and the ascending caller
displaylog number will be shown. For example: Phone number 0462805000, time
received 18:08 on the 16th of October. Caller display ID log number is 20. DORO is
stored in the phonebook memory.
OUT OF AREA
If the display shows "OUT OF AREA" instead of a telephone number, this means that
no information was received from the Network. The call may have been an international
call or from a PBX.
PROTECT
If the display shows "PROTECT" it indicates that the calling number is an unlisted
(silent) number or the caller has barred the number so it will not be displayed. It could
also come from a mobile telephone or a PBX.
CALLER DISPLAY LOG FULL
When the call log is full (15 calls) the oldest call will be deleted automatically.