Dors 1170 User manual

USER MANUAL
www.dors.com
Pantone 300C EBKM.1100M1.00.00.000-02UM Int
11
70
MULTIFUNCTIONAL COUNTERFEIT DETECTOR
1170
DORS, LLC
26A 1st Vladimirskaya Str., Moscow 111141 Russia
www.dors.com
User Manual
Rev 0Int © KB DORS LLC, 2016
Production date:

FOR NOTES
3
MULTIFUNCTIONAL COUNTERFEIT DETECTOR DORS 1170
Thank you for purchase of the multifunctional detector DORS 1170D.
READ THIS MANUAL THOROUGHLY
BEFORE OPERATING THE DEVICE!
BRIEF INFORMATION FOR CUSTOMER
The multifunctional detector DORS 1170D is developed in Russia by
DORS R&D and is assembled in China by DORS Industries (China) Ltd.,
Service term is 7 years*.
* Under condition that detector is being used in strict accordance with this
user manual and applied technical standards.
CONTENT
BRIEF INFORMATION FOR CUSTOMER............................................ 3
THE PURPOSE OF THE DETECTOR.................................................. 4
IMPORTANT INFORMATION................................................................ 4
SAFETY PRECAUTIONS...................................................................... 4
DELIVERY SET ............................. ........................................................ 5
APPEARANCE AND KEY COMPONENTS OF THE DEVICE ........... ... 6
PREPARING FOR OPERATION ..................... ...................................... 7
OPERATION ........................... ............................................................... 7
DESCRIPTION OF THE TYPES OF CONTROL................................... 9
TROUBLESHOOTING........................................................................... 11
SPECIFICATIONS.................................................................................. 12
TRANSPORTATION, STORAGE AND DISPOSAL 2................................ 1
SUPPORT AND WARRANTY................................................................. 12

4
The multifunctional detector DORS 1170D (henceforth – the device) is
designed for visual detection of authenticity of banknotes and security
printing documents with protective marks that can be verified by this device.
Device features
The device is equipped with:
• 7” colour LCD TFT display,
• Infrared camera that transmits to the display a general view of
banknote (document) placed closely to the device,
• Source of infrared (IR) light (850nm and 940nm) intended to illuminate
the viewing area of general view camera,
• 10x camera that transmits to the display a magnified view of a part of
banknote (document),
• Source of IR, white, and ultraviolet (UV) lights intended to illuminate
the viewing area of 10x camera,
• Digital video output for connection to PC using an USB interface.
The device helps to:
1 Check the presence of IR images in reflected light, including a mode of
interchangeable wavelengths (940nm and 850nm).
2 Check an authenticity of security elements made by Orloff intaglio
printing (these elements can be printed in several colours or by
metameric ink).
3 Check the presence of intaglio printing at the certain elements of a
banknote.
4 Check the presence and authenticity of banknote’s microperforation.
5 Check the banknote’s general luminescence under UV light.
6 Verify the UV images (pictures, protective threads and fibers).
7 Transfer the image from device’s screen to PC for examination and
saving for a further reference.
The viewing area of 10x camera is available for examination by naked
eye. It allows to combine a visual control of UV images and a control by
means of device’s sensors.
The device has the only button that makes its usage fast and simple.
The device can be used by a cashier that has been trained to verify an
authenticity of banknotes – upon a condition that this manual has been read
attentively.
DELIVERY SET
Multifunctional counterfeit detector DORS 1170D................................ 1 pc.
AC adapter............................................................................................ 1 pc.
User manual.......................................................................................... 1 pc.
Packaging............................................................................................. 1 set
THE PURPOSE OF THE DETECTOR
5
IMPORTANT INFORMATION!
:Safety precautions
IT IS PROHIBITED TO TOUCH THE DEVICE AND THE POWER CORD PLUG
WITH WET HANDS. IT MAY RESULT IN AN ELECTRIC SHOCK.
WARNING! TO AVOID ANY DAMAGE OF THE CABLE OR ITS BREAK,
UNPLUG THE POWER CORD FROM THE POWER OUTLET BY GETTING HOLD
OF ONLY THE PLUG.
ATTENTION! IF THE DEVICE HAS BEEN UNDER COLD CONDITIONS FOR A
LONG TIME, IT SHALL BE KEPT UNDER ROOM TEMPERATURE FOR NOT LESS
THAN TWO HOURS BEFORE ITS SWITCHING ON.
ATTENTION! TO PROVIDE A SUCCESSFUL OPERATION OF THE DEVICE FOR A
LONG TIME WITHOUT A SERVICE ENGINEER’S INTERFERENCE, PLEASE
OBSERVE THE FOLLOWING RULES:
• THE DEVICE SHALL BE INSTALLED ON AN EVEN HORIZONTAL SURFACE;
• WHEN INSTALLING THE DEVICE, AVOID ITS EXPOSURE TO DIRECT
SUNLIGHT AND ARTIFICIAL SPOT LIGHT.
MULTIFUNCTIONAL COUNTERFEIT DETECTOR DORS 1170MULTIFUNCTIONAL COUNTERFEIT DETECTOR DORS 1170

7
6
APPEARANCE AND KEY COMPONENTS
OF THE DEVICE
Front view Rear view
1170
1
2
3
5
4
1
Control button
2
3
General view camera
Screen
4Jack for AC adapter
510x camera
6Slot for banknote
Fig. 1. Appearance of the device
Control button (item 1 of Fig.1) is intended for switch on / off the device,
for switching between general view camera and 10x camera. The button is
sensitive to three types of touch: short, long, and double.
Screen (item 3 of Fig.1) is designed to display the general view of
banknote under IR light or the part of banknote with 10x magnification.
Besides, the symbol of current mode is indicated in the left bottom corner of
the screen.
General view camera (item 2 of Fig.1) captures the full-size image of
banknote for its further displaying on the screen of device. To examine a
banknote, put it on the table close to detector’s base or hold it in hands. The
camera produces the picture in infrared light that allows a user to watch the
infrared image of a banknote. The general view camera is equipped with 2
sources of IR light (at wavelengths 850nm and 940 nm). If a banknote has a
security element which image at 850nm is different of that at 940nm (for
example, US dollars), a user has to activate a mode of blinking IR (i.e.
interchangeable turning on both sources). Therefore in blinking IR mode a
user sees on the display a blinking of such security element.
Slot for banknote (item 6 of Fig.1) is designed to insert a banknote (short
size forward) in order to examine it with 10x magnification or to verify its UV
image. Once a banknote is inserted into the slot, the screen automatically
displays an image captured by 10x camera. If there is no banknote in the slot,
the screen displays an image from the general view camera.
10x camera (item 5 of Fig.1) is located just above the slot. A user can see
the viewing area of 10x camera through a transparent glass of a front panel of
detector. This camera is equipped with 3 sources of light in order to verify the
different security features:
• Double-sided white oblique light allows to examine a microstructure
of a printed layer of a banknote, including tangier grids and guilloches,
and microlettering as well. 10x magnification is good enough for
verification of Orloff intaglio printing. Due to small angle of incidence of
a beam, user can see relief and structure of paper’s surface, a height of
printing layer’s relief, and a microperforation. When white light is on,
user can see a banknote through a transparent glass and find faster a
fragment for examination with a magnification.
• Double-sided IR oblique light allows to examine IR images and their
microstructure. IR light applied together with white light helps to verify
an authenticity of Orloff intaglio printing made by metameric ink, and
makes visible a raised relief of paper in the areas covered by
metameric ink to verify an authenticity of intaglio printing.
• UV light at wavelength 365nm makes visible UV images and a
banknote’s general luminescence under UV light. This control mode
allows to watch a microstructure of UV images, including luminescent
fibers of paper. Looking through a transparent glass, user can move a
banknote to examine certain elements of UV images.
Digital video output (item 8 of Fig.1) is designed to transfer a picture
from device to PC through mini-USB cable. If the relevant driver is installed on
PC, the latter recognizes the device as a video source. The transferred
picture can be displayed on PC’s monitor and can be saved as digital image
or video file.
The text messages displayed on the screen of device (refer to Fig.4)
do not transferred through the digital video output.
7Mini-USB jack
(digital output)
7
6
Take the detector out of its package and install it on a desk thus a screen of
device faces a user. Provide a free space in front of detector in order to place
a banknote inside a viewing area of general view camera, as well as behind a
device to let a banknote pass through the slot.
If it is supposed to transfer a picture from device to PC, connect mini-USB
jack of device to USB port of PC using relevant cable (a cable is not included
in the delivery set). Install to PC a special driver that can be downloaded from
DORS web site.
To start the device operation, connect the supplied AC adapter to the
power jack of the device (item 4 of Fig.1) and plug AC adapter to power
supply 100 -240V ~50/60 Hz. Then switch on the device by long press (about
1 second) on the control button (item 1 of Fig.1). The screen of device shall
turn on to show that the device is switched on and ready to operation.
PREPARING FOR OPERATION
OPERATION
You can choose the operation mode by putting a banknote on the table
close to detector’s base (general view mode, refer to Fig.2) or by inserting a
banknote into the slot (zoom mode, refer to Fig.3). Depending on a position
of a banknote, the device chooses the required operation mode auto-
matically. To choose a certain source of light in any operation mode, use the
control button. The list of available types of control is given in Spreadsheet 1.
MULTIFUNCTIONAL COUNTERFEIT DETECTOR DORS 1170MULTIFUNCTIONAL COUNTERFEIT DETECTOR DORS 1170

1170
1x IR
IR
1x IR
IR
8 9
Position
of
a banknote
Operation mode &
type of light On-screen indication of
a control mode
Before
the device
In the slot
General view mode,
IR control (both 850nm and 940nm)*
General view mode, IR blinking control
(interchangeable 850nm / 940nm)
1x IR
1х IR BLINK
Zoom mode,
White light control*
Spreadsheet 1
* This type of light is activated after the device is switched on.
Fig.4 shows where on the screen the messages are indicated.
The functions of the control button (item 3 of Fig.1):
1. If the device is switched off, the long pressing of the control button (about 1
second) switches it on.
2. In the general view mode (refer to Fig.2), a short pressing of the control
button switches the device between IR control and IR blinking control.
• IR control (1x IR) is supported by wideband infrared light (830nm to
960nm).
• IR blinking control (1x IR BLINK) is supported by interchangeable
infrared light (850nm / 940nm). If a banknote has IR blinking mark, the
latter appears and disappears on the screen of device.
3. In the zoom mode (refer to Fig.3), a short pressing of the control button
subsequently switches the following types of light for 10x camera:
• Permanent white light (10x WHITE),
• Interchangeable light for control of intaglio printing by metameric inks
(10x INTAGLIO),
• Permanent IR light (10x IR),
• Permanent UV light (10x UV).
Then these types of light are repeated by cycle. Double click on the control
button reverses the sequence.
4. If the device is switched on, the long pressing of the control button (about 1
second) switches it off.
Note: The status of a light source is saved separately for the general view
mode and for the zoom mode. When you re-enter an operation mode, the
status of its light source is restored automatically.
Fig.2
General view
control mode
Fig.3
Zoom
control
mode
DESCRIPTION OF THE TYPES OF CONTROL
IR control
Place a banknote to be verified close to detector’s base. Do not expose a
banknote under a direct sunlight or artificial spot light. Otherwise an
examination of IR image will be difficult or even impossible. Activate IR
control (a message «1x IR» is appeared on the screen of device). Examine IR
image of a banknote on the screen of device. Compare IR image on the
screen with that of genuine banknote of the same denomination and
generation.
IR blinking control
Place a banknote to be verified close to detector’s base. Do not expose a
banknote under a direct sunlight or artificial spot light. Otherwise an
examination of IR image will be difficult or even impossible. Activate IR
blinking control (a message «1x IR BLINK» is appeared on the screen of
device). Examine IR image of a banknote on the screen of device. IR images
should distinctly blink approx. 2 times per second.
Type
of
camera
General view
camera
10х camera
10х WHITE
10х INTAGLIO
Zoom mode,
Control of intaglio printing by metameric ink
(interchangeable white light and IR light)
Zoom mode,
IR control
Zoom mode,
UV control
10х IR
10x UV
Viewing area of
10x camera
1170
1170
Viewing area
of the general
view camera
10x IR
IR
Fig.4. Indication of
an operation mode
and a type of control
on the screen of device
MULTIFUNCTIONAL COUNTERFEIT DETECTOR DORS 1170MULTIFUNCTIONAL COUNTERFEIT DETECTOR DORS 1170

10 11
Control of IR images made by intaglio printing
Insert a banknote to be verified into the slot. Activate the control of intaglio
printing (a message «10x INTAGLIO» is appeared on the screen of device).
Looking at the viewing area of 10x camera, check whether an IR image made
by intaglio printing is visible. A part of such IR image is printed by IR-
transparent (metameric) ink, while its other part is printed by IR-non-
transparent ink. Make sure that A) on the screen of device a part of such IR
image is completely disappeared and re-appeared while its other part is
always visible; B) thin lines of image continue without interruptions or steps.
UV control
Insert a banknote to be verified into the slot. Activate the UV control mode
(a message «10x UV» is appeared on the screen of device).
• Looking at the viewing area of 10x camera, check whether a fragment
with UV image is visible. Watch UV image, pay attention to a color of its
luminescence. Make sure that UV image on the screen matches this
type of banknote. The information on location and content of UV
image(s) at certain banknote is available on web site of the relevant
Central Bank.
• Looking at the viewing area of 10x camera, check whether a fragment
without UV images is visible. Make sure that there is no background
luminescence of a banknote. A counterfeit note usually has bright
background luminescence (white or light blue).
• Looking at the viewing area of 10x camera, find a fragment with a
luminescent fibre. Such fibres are distributed over a surface of a
genuine banknote in a random way. Watch a fibre on the screen. It
should look thin, even, and well-shaped. It’s allowed that a fibre has a
brightly luminescent thickening with sharp edges. If a fibre is too thick
and its edge is uneven and blur, it can testify that this fibre is forged.
Switching off the device
Press the control button by long touch, upon that the screen of the device
has to be faded. Take the AC adapter off the electrical socket.
Control of intaglio printing
Insert a banknote to be verified into the slot. Activate the control of intaglio
printing (a message «10x INTAGLIO» is appeared on the screen of device).
Looking at the viewing area of 10x camera, check whether an image with
a raised relief printed by IR-transparent (metameric) ink is visible. Make sure
that A) when an image on the screen is disappeared, on its place you see a
raised relief of banknote’s paper; B) a raised relief is situated on the same
place and has the same shape that an image on the screen. This type of
control can be combined with a detailed control of IR images.
Control of Orloff intaglio printing made by multicolor inks
Insert a banknote to be verified into the slot. Activate the white light control
mode (a message «10x WHITE» is appeared on the screen of device).
Looking at the viewing area of 10x camera, check whether a fragment of a
banknote printed by Orloff intaglio printing with multicolor inks is visible. This
area has the image(s) printed in two colors in such way that the lines suddenly
change their colors without interruption or step or blur. Carefully examine the
contacts of sections of different colors. This type of control is also available in
the intaglio printing control mode (a message «10x INTAGLIO» is on the
screen).
Control of microperforation
Insert a banknote to be verified into the slot. Activate the control of intaglio
printing (a message «10x INTAGLIO» is appeared on the screen of device).
Looking at the viewing area of 10x camera, check whether a microperforated
fragment is visible. You need to see on the screen at least 4 holes of
microperforation. Make sure that: A) all these holes are equal in size, have
even edges, with no prominent fibres, with no traces of burning, B) there is no
raising relief around a hole.
Control of microlettering
Insert a banknote to be verified into the slot. Activate the control of intaglio
printing (a message «10x INTAGLIO» is appeared on the screen of device).
Looking at the viewing area of 10x camera, check whether a fragment with
microlettering is visible. Make sure that the microlettering on the screen is
readable, its content matches this type of banknote, the lines have no
interruption or ink spreading. The information on location and content of
microlettering at certain banknote is available on web site of the relevant
Central Bank. This type of control is also available in the white light control
mode (a message «10x WHITE» is on the screen).
Maintenance
To clean the soiled surfaces of the device, use a neutral water-based
detergent (like dishwashing liquid) or a cleaning stuff based on isopropyl
alcohol. A surplus of detergent or cleaning stuff should be carefully removed
from the surfaces of the device.
WARNING! BEFORE A CLEANING OF DEVICE’S SURFACE, MAKE SURE
THE AC ADAPTER HAS BEEN REMOVED FROM THE ELECTRIC SOCKET!
WARNING! TO AVOID AN ELECTRIC SHOCK, PREVENT A PENETRATION OF
A DETERGENT OR A CLEANING STUFF INSIDE THE DEVICE!
WARNING! WHEN YOU CLEAN THE SURFACE OF DEVICE, USE ONLY A
SOFT TISSUE TO APPLY A DETERGENT OR A CLEANING STUFF. IT IS
PROHIBITED TO USE A BRUSH, A SPRAYER OR AN AEROSOL SPRAY TO
APPLY A DETERGENT OR A CLEANING STUFF.
TROUBLESHOOTING
The device fails to switch on (the screen doesn't light).
Check the device connection to AC adapter. Remove AC adapter from
electric socket, wait one minute, then insert again the adapter into electric
socket, and try to switch on a device. If the device still fails to switch on, call
your supplier.
MULTIFUNCTIONAL COUNTERFEIT DETECTOR DORS 1170MULTIFUNCTIONAL COUNTERFEIT DETECTOR DORS 1170

12 13
SPECIFICATIONS
Supply voltage of AC adapter ........................... 100V – 240V, 50/60 Hz
Current consumption of AC adapter.................. 0.15A – 0.06A
Supply voltage of detector ................................ 5V DC
Current consumption of detector ...................... not more than 1.5A
Net weight (incl. AC adapter) / gross weight ...... 0.32kg / 0.54kg
Overall dimensions (Width x Depth x Height): .. 122x111x245 mm
Width of the slot for banknote ........................... 114 mm
Screen size...................................................... 7” (177mm)
Linear magnification on the screen:
general view camera ....................................... 1x
10x camera ……………................................... 10x
Light sources of general view camera:
IR mode ........................................................... wideband 830nm - 960nm
IR blink mode ................................................... 850nm / 940nm
Light sources of 10x camera:
IR mode ........................................................... double-side oblique 940nm
Visible mode .................................................... double-side oblique white
light
UV mode ......................................................... direct 365nm
Power of the laser ............................................ 50mW
Digital video output interface............................. USB 2.0
Operating temperature..................................... +5 оC to +35оC
о
Relative humidity of the air at +25 C.................. 40% to 80%
Atmospheric pressure...................................... 84kPa to 107 kPa
TRANSPORTATION, STORAGE AND DISPOSAL
The device shall be transported in its standard package by sea (in
containers), by railway (in closed wagons), by air (in a pressurized baggage
or a cargo compartment), and by truck (in an enclosed body or in a container
under a waterresistant tent along the public paved roads). The transportation
conditions are temperature – 30°C to + 50°C, relative humidity up to 95 %
without water condensation at +25°C, atmospheric pressure 84 to 107 kPa
(630 to 800 mm Hg).
The device shall be stored in its package in a heated warehouse at
temperature +10°C to +25°C, at relative air humidity not exceeding 80%.
The device meets the requirements of the European Union's RoHS Directive
which decreases the environmental pollution by hazardous substances. The
device may be disposed as a domestic waste.
SUPPORT AND WARRANTY
The manufacturer guarantees 12 month of the device operation since
the moment of its purchase. The manufacturer by means its local dealer is
obliged to repair the failed device if the user has observed all the
requirements of this User Manual.
FOR NOTES
MULTIFUNCTIONAL COUNTERFEIT DETECTOR DORS 1170MULTIFUNCTIONAL COUNTERFEIT DETECTOR DORS 1170