D+H VCD 204 User manual

VCD 204 instructions
Please order bracket sets separately
VCD 204/yyy
VCD 204/yyy-DS
Option – loopthrough (DS)

99.831.06 1.3/02/16
4/16 Deutsch
VCD 204 VCD 204
Safety extra low voltage 24 V DC!
Do not connect directly to the mains supply!
- Connection has to be carried out only by an
authorized electrical specialist
- Danger of violent pressure in handaccessible area
- Keep away People from the operating area of the
drive
- Keep away children from the control
- Use only in dry rooms
- Only for inside mounting.
Use rain detector with danger of rain
(e.g. at domelights or roof windows)
- Just use unchanged original D+H parts
- Observe mounting instructions of bracket set!
Observe enclosed r ed safety slip!
Safety notes
Intended use
- Chain drive for electric opening and closing of
windows and flaps in the facade and roof area
- Useable for daily natural ventilation
- Operating voltage 24 V DC
- Only for inside mounting
Drive unit with 2,5 m PVC cable. Dependent on the
type of window, different bracket sets are available
separately.
Extent of supply
Performance features
- Micro processor controlled electronics
- Individually programmable via Powerline (PLP1
and SCS)
- Stroke programming with magnet
- Low running noises
- Connection via plug connector
- Symmetrical chain outlet
- Tandem-safety function for operation of two
VCD 204 drives on one sash
Up to two VCD 204 drives and one locking drive can be
used in tandem. Combined TMS+ and BRV signal.
The BRV signal is only output when in the end
position - this prevents locking drives and modules
from malfunctioning.
During the learning phase, the activated stroke is
transferred to the tandem drive via the TMS+
function.
TMS+ / -BRV function
Bei der Verwendung von zwei VCD 204 an einem Fenster müssen zum Hub einstellen beide
Antriebe elektrisch verbunden sein, es muss aber nur ein Antrieb mit dem Magnet in den
Hubanlernmodus versetzt werden.
Hubbegrenzung mit Magnet
Antrieb einfahren.
1Antrieb so lange in AUF-
Richtung fahren lassen bis
gewünschter Hub erreicht wurde.
Sollte ein falscher Hub eingestellt
oder versehentlich die Fahrt
unterbrochen worden sein
oder der Antrieb wieder auf
maximale Hublänge gebracht
werden, muss wieder mit Punkt 1
begonnen werden.
STOP
3
Am Antrieb muss in ZU-
Richtung weiter Spannung
anliegen.
Magnet anAntrieb halten (ca. 2
sek.), bis nach einem pulsie-
renden Ton ein Dauerton kommt
> Antrieb ist im Anlernmodus.
Der Magnet kann entfernt werden.
Die Spannung muss nicht mehr
am Antrieb anliegen.
ca.100 mm
Anlernmodus
ca. 2 sek.
2
Antriebe mechanisch spannungsfrei montieren.
Hierdurch wird eine gleichmäßigere Lastverteilung
auf alle Antriebe gewährleistet.
Montagehinweise
Elektrogeräte, Zubehör, Batterien und Verpackungen
sollen einer umweltgerechten Wiederverwertung
zugeführt werden. Werfen Sie Elektrogeräte und
Batterien nicht inden Hausmüll!
Nur für EU-Länder:
Gemäß der Europäischen Richtlinie 2012/19/EU
über Elektro- und Elektronik-Altgeräte und ihrer
Umsetzung in nationales Recht müssen nicht mehr
gebrauchsfähige Elektrogeräte getrennt gesammelt
und einer umweltgerechten Wiederverwertung
zugeführt werden.
Entsorgung
Maintenance and cleaning
Maintenance work is only allowed when the device is in
a de-energized condition! Inspection and maintenance
has to be carried out according to D+H maintenance
notes. Only original D+H spare parts may be used.
Repair is to be carried out exclusively by D+H.
Wipe away debris or contamination with a dry, soft
cloth.
Do not use cleaning agents or solvents.
Guarantee
You will get 2 years guarantee for all D+H products
from date of verified handing over of the system up to
maximal 3 years after date of delivery, when
mounting and starting has been carried out by an
authorized D+H-distributor.
D+H guarantee is expired, with connection of D+H
components with external systems or with mixing of
D+H products with parts of other manufacturers.
Declaration of Conformity
We declare under our sole responsibility that the
product described under “Technical Data” is in
conformity with the following directives:
2014/30/EU, 2014/35/EU
Technical file at:
D+H Mechatronic AG, D-22949 Ammersbek
Dirk Dingfelder Maik Schmees
Member of the Board Authorized signatory, Technical Director
24.02.2016
WARNING
Read all safety warnings, instructions, illustrations
and specifications provided with this product.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.

English
99.831.06 1.3/02/16 VCD 204
VCD 204 7/16
Closing edge protection
In the "CLOSE" direction the drive has an active
protection for the main closing edge. If there is an
overload in the closing ranges 3 and 2, the drive runs
"OPEN" for 20 seconds, then "CLOSE" again. If
closing is not possible after three attempts, the drive
remains in this position.
In addition, the drive is equipped with passive
protection. The closing speed in closing range 2 and
1 is reduced to 5 mm/s.
Significantly greater forces can be
exerted at the secondary closing edges.
Danger of crushing hands and fingers!
Main closing edge
Beside closing edge
Beside - closing edge
Stroke limiting with magnets
Voltage must continue to
be applied to the drive when
moving in the “CLOSE”
direction. Hold the magnet next
to the drive as shown in the
diagramme (2 sec.) until you hear
a pulsating ton > The drive is now
in learning mode. The magnet can
now be removed and the drive no
longer has to be under voltage.
Close drive.
1Allow the drive to run
“OPEN” until you reach the
required stroke.
If the stroke is set incorrectly,
the procedure is accidentally
interrupted or the drive
continues to the full stroke
length, please return to point 1
and start again.
STOP
3
appr.100 mm
learning mode
appr. 2 sec.
2
When using two VCD 204s on one window, both drives must be electrically connected in order to
set the stroke, although only one drive needs to be switched to the stroke learning mode with the
magnet.
All forces + approx. 20 % switch-off reserve (temporary)
Closure Ranges
~6 mm/s
150 N
(Safety cut-off force)
5 mm/s
150 N
77 mm
~6 mm/s
200 N
23 mm
Mount the drives mechanical stress-free.
With that, a better load distribution is ensured on all
the drives.
Mounting informations
Running speed and forces
Type VCD 204
Power supply 24 V DC / ± 20 %
Nominal current 0,35 A
Nominal force 200 N
Nominal locking force approx. 2000 N (Excluding bracket)
Service life >20 000 double strokes
Duty cycle 30 % (With cycle time 10 minutes)
Housing Zinc-diecasting, powdercoated
Ingress protection IP 30
Temp. range 0 ... +60 °C
Emission sound pressure level LpA ≤ 70 dB(A)
/
Nominal stroke length * ** See type plate
Additional functions ** Closing edge protection activated (3 stroke repeatings);
Locking relief activated
*Adjustable with PLP 1 ** Programmable with PLP 1 and SCS
Technical data
Electrical devices, accessories, batteries and packa-
ging should be sorted for environmental-friendly
recycling. Do not dispose electrical devices and
batteries into household waste!
Only for EC countries:
According the European Guideline 2012/19/EU for
waste electrical and electronic equipment and its
implementation into national right, electrcal devices
that are no longer usable must be collected separa-
tely and disposed of in an environmentally correct
manner.
Disposal

English 99.831.06 1.3/02/16
VCD 204
6/16 VCD 204
Closing edge protection
In the "CLOSE" direction the drive has an active
protection for the main closing edge. If there is an
overload in the closing ranges 3 and 2, the drive runs
"OPEN" for 20 seconds, then "CLOSE" again. If
closing is not possible after three attempts, the drive
remains in this position.
In addition, the drive is equipped with passive
protection. The closing speed in closing range 2 and
1 is reduced to 5 mm/s.
Significantly greater forces can be
exerted at the secondary closing edges.
Danger of crushing hands and fingers!
Main closing edge
Beside closing edge
Beside - closing edge
Stroke limiting with magnets
Voltage must continue to
be applied to the drive when
moving in the “CLOSE”
direction. Hold the magnet next
to the drive as shown in the
diagramme (2 sec.) until you hear
a pulsating ton > The drive is now
in learning mode. The magnet can
now be removed and the drive no
longer has to be under voltage.
Close drive.
1Allow the drive to run
“OPEN” until you reach the
required stroke.
If the stroke is set incorrectly,
the procedure is accidentally
interrupted or the drive
continues to the full stroke
length, please return to point 1
and start again.
STOP
3
appr.100 mm
learning mode
appr. 2 sec.
2
When using two VCD 204s on one window, both drives must be electrically connected in order to
set the stroke, although only one drive needs to be switched to the stroke learning mode with the
magnet.
All forces + approx. 20 % switch-off reserve (temporary)
Closure Ranges
~6 mm/s
150 N
(Safety cut-off force)
5 mm/s
150 N
77 mm
~6 mm/s
200 N
23 mm
Mount the drives mechanical stress-free.
With that, a better load distribution is ensured on all
the drives.
Mounting informations
Running speed and forces
Type VCD 204
Power supply 24 V DC / ± 20 %
Nominal current 0,35 A
Nominal force 200 N
Nominal locking force approx. 2000 N (Excluding bracket)
Service life >20 000 double strokes
Duty cycle 30 % (With cycle time 10 minutes)
Housing Zinc-diecasting, powdercoated
Ingress protection IP 30
Temp. range 0 ... +60 °C
Emission sound pressure level LpA ≤ 70 dB(A)
/
Nominal stroke length * ** See type plate
Additional functions ** Closing edge protection activated (3 stroke repeatings);
Locking relief activated
*Adjustable with PLP 1 ** Programmable with PLP 1 and SCS
Technical data
Electrical devices, accessories, batteries and packa-
ging should be sorted for environmental-friendly
recycling. Do not dispose electrical devices and
batteries into household waste!
Only for EC countries:
According the European Guideline 2012/19/EU for
waste electrical and electronic equipment and its
implementation into national right, electrcal devices
that are no longer usable must be collected separa-
tely and disposed of in an environmentally correct
manner.
Disposal

Standard Optional signals
max. 50 V / 0,5 A
WH (Mot. a)
YE (TMS+/BRV)
BN (Mot. b)
GN (SZ (no))
GY (SZ+SA (o))
PK (SA (no))
-SA-SZ
WH (Mot. a)
YE (TMS+/BRV)
BN (Mot. b)
GN (SKS)
GY (SKS)
-SKS
WH (Mot. a)
YE (TMS+/BRV)
BN (Mot. b)
GN (SGI)
GY (SGI)
-SGI
WH (Mot. a)
YE (TMS+/BRV)
BN (Mot. b)
WH (+24 V)
YE (TMS+)
BN (–)
GN (n.c.)
WH (+24 V)
YE (TMS+)
BN (–)
GN (n.c.)
VCD 204/yyy
WH (Mot. a)
YE (TMS+/BRV)
BN (Mot. b)
VCD 204/yyy-DS
Option – loopthrough (DS)
Standard
Options see above
99.831.06 1.3/02/16 VCD 204
VCD 204 15/16
DE / EN / FR / ES
Anschluss / Connection / Connexion / Conexión
Mot. b
(BN)
Mot. a
(WH)
(BN) brown
(YE) yellow
(GN) green
(WH) white
(PK) pink
(GY) grey
Pin Assigment
1 Antrieb / 1 drive /
1 motorisation / 1 motore
max. 2 Antriebe / max. 2 drives /
max. 2 motorisations / máx. 2 motores
(BN)
(YE)
(WH)
Mot. b
TMS+ /
BRV
Mot. a
VCD 204/yyy
Mot. b
TMS+ /
BRV
Mot. a
(BN)
(YE)
(WH)
VCD 204/yyy
Mot. a Mot. b
Abzweigdose /
Junction box /
Boîte de dérivation /
Caja de conexión
max. 2 Antriebe / max. 2 drives /
max. 2 motorisations / máx. 2 motores
GN (n.c.)
GN (n.c.)
Gegen Kurzschluss sichern /
Protect against short circuit /
Protéger contre les courts-circuits /
Proteger contra cortacircuitos
(BN)
(YE)
(WH)
Mot. b
TMS+ /
BRV
Mot. a
VCD 204/yyy
Mot. a Mot. b
Abzweigdose /
Junction box /
Boîte de dérivation /
Caja de conexión
Mot. b
TMS+ /
BRV
Mot. a
(BN)
(YE)
(WH)
VCD 204/yyy
(BN)
(YE)
(WH)
Mot. b
TMS+ /
BRV
Mot. a
VCD 204/yyy-DS
Option - Durchgeschliffen (DS) /
Option – loopthrough (DS) /
Option – Bouclé (DS) /
Opcional – Lijado (DS)
Gegen Kurzschluss sichern /
Protect against short circuit /
Protéger contre les courts-circuits /
Proteger contra cortacircuitos
Mot. a Mot. b
Abzweigdose /
Junction box /
Boîte de dérivation /
Caja de conexión

Standard /
Estándar
Optionale Meldungen / Optional signals /
Signals optional / Señales opcional
max. 50 V / 0,5 A
WH (Mot. a)
YE (TMS+/BRV)
BN (Mot. b)
GN (SZ (no))
GY (SZ+SA (o))
PK (SA (no))
-SA-SZ
WH (Mot. a)
YE (TMS+/BRV)
BN (Mot. b)
GN (SKS)
GY (SKS)
-SKS
WH (Mot. a)
YE (TMS+/BRV)
BN (Mot. b)
GN (SGI)
GY (SGI)
-SGI
WH (Mot. a)
YE (TMS+/BRV)
BN (Mot. b)
WH (+24 V)
YE (TMS+)
BN (–)
GN (n.c.)
WH (+24 V)
YE (TMS+)
BN (–)
GN (n.c.)
VCD 204/yyy
WH (Mot. a)
YE (TMS+/BRV)
BN (Mot. b)
VCD 204/yyy-DS
Option - Durchgeschliffen (DS) / Option – loopthrough (DS) /
Option – Bouclé (DS) / Opcional – Lijado (DS)
Standard
Options see above / Options see above /
Options voir haut / Opciones ver más arriba
99.831.06 1.3/02/16
VCD 204
14/16 VCD 204
DE / EN / FR / ES
Connection
Mot. b
(BN)
Mot. a
(WH)
(BN) braun / brown / brun / marrón
(YE) gelb / yellow / jaune / amarillo
(GN) grün / green / vert / verde
(WH) weiss / white / blanc / blanco
(PK) rosa / pink / rose / rosa
(GY) grau / grey / gris / gris
AderbelegungStecker / Pin Assigment / Brochagedes fiches/ Asignacióndecables
1 Antrieb / 1 drive /
1 motorisation / 1 motore
max. 2 drives
(BN)
(YE)
(WH)
Mot. b
TMS+ /
BRV
Mot. a
VCD 204/yyy
Mot. b
TMS+ /
BRV
Mot. a
(BN)
(YE)
(WH)
VCD 204/yyy
Mot. a Mot. b
Junction box
max. 2 drives
GN (n.c.)
GN (n.c.)
Protect against short circuit
(BN)
(YE)
(WH)
Mot. b
TMS+ /
BRV
Mot. a
VCD 204/yyy
Mot. a Mot. b
Junction box
Mot. b
TMS+ /
BRV
Mot. a
(BN)
(YE)
(WH)
VCD 204/yyy
(BN)
(YE)
(WH)
Mot. b
TMS+ /
BRV
Mot. a
VCD 204/yyy-DS
Option – loopthrough (DS)
Protect against short circuit
Mot. a Mot. b
Junction box

30 mm
41,2 mm
480 mm
47 mm
aa
Dimensions
Dyer Environmental Controls Ltd
Unit 10 Lawnhurst Trading Estate, Cheadle Heath,
Stockport SK3 0SD
Tel: [phone]
E-Mail: [email protected]
www.dyerenvironmental.co.uk