Dräger BiliLux User manual

User Quick Reference Guide
BiliLux LED Phototherapy Light
© Drägerwerk AG & Co. KGaA
WARNING!
This quick guide is intended for informational purposes only. It is not a
replacement or substitute for the Instructions for Use. Any use of this medical device
requires a full understanding and strict observation of the Instructions For Use.
SCAN QR code
for FAQs, product and application information, usage and reprocessing of
the Dräger medical device.
CONTACT
your local representative for further information
Effective Phototherapy

Page | 2
BiliLux LED Phototherapy Light
Effective Spectrum ●High Irradiance ●Effective Surface Area
The BiliLux phototherapy light has its irradiance peaks in the most effective
wavelength range to reduce the bilirubin which is 460-490nm. By achieving
extremely high irradiance levels >30 μW/cm2/nm, the BiliLux fulfills the
requirements of intensive phototherapy. The irradiance can be dimmed in five
steps to provide the adequate therapy for the patient. The phototherapy light
features a large surface area to cover full term and premature babies. The
irradiance is evenly distributed over the entire mattress to ensure superior
1
Top View
1. Control Panel
2. Quick-Connect Plug (connection to spring arm)
2

Page | 3
BiliLux LED Phototherapy Light
Bottom View
1. Blue Phototherapy LED Lights
2. White Observation LED Lights
3. Rating Plate
2
3
1
1. On/off switch
2. Power cable receptacle
3. Quick-connect plug (connection to spring arm)
4. RS-232 communication port
5. Receptacle for radiometer cable
6. USB port
1
2
4
Rear View
6
5
3

Page | 4
BiliLux LED Phototherapy Light
1. Quick-connect for phototherapy light
2. Spring arm
3. Cable clips
4. Rail clamp for phototherapy light (to connect to pole/rail)
BiliLux with Optional Spring Arm
1
4
3
2

Page | 5
BiliLux LED Phototherapy Light
1. Spring arm
2. Tightening knob for spring arm
3. Trolley pole
4. Height adjustment knob
5. Cable holder (optional)
6. Trolley base with locking castors
BiliLux with Optional Trolley
1
2
3
4
5
6

Page | 6
BiliLux LED Phototherapy Light
Radiometer (optional)
1. Sensor
2.
Store
button (to store an irradiance measurement)
3. Cable (to connect to phototherapy light)
4. Calibration due date label
5. Magnets
1
2
3
4
5

Page | 7
BiliLux LED Phototherapy Light
1. Key to start, pause, and resume therapy.
2. Key to decrease irradiance of phototherapy light in 5 decrements
of 20%.
3. Key to increase irradiance of phototherapy light in 5 increments
of 20%.
4. On/off key for observation light. The observation light operates
independently of the phototherapy light.
5. Menu key used to select among various operational and service
screens.
6. Buttons whose functions are defined on the currently selected
screen.
7. LED indicators for irradiance of phototherapy light. Each bar
represents an increment of 20%. One bar indicates 20% irradiance
and five bars indicates 100% irradiance.
8. On/Off LED indicator for observation light.
How to Operate
2
3
4
5
6
7
8
1

Page | 8
Displaying BiliLux Screens
The user can display the following screens:
oPhototherapy screen (default)
oRadiometer screen
oPhototherapy report screen
oConfiguration screen
oDevice status screen
1.
To navigate to the next screen, press the key once
oThe screens will be displayed in succession.
oPhototherapy can continue while the user navigates among
different screens.
oAfter 15 seconds of inactivity (3 minutes on the radiometer
screen), the display reverts to the default phototherapy screen.
BiliLux LED Phototherapy Light
1

Page | 9
BiliLux LED Phototherapy Light
Phototherapy Screen (Default)
oShows the elapsed duration of therapy in hours and minutes,
as well as therapy status (on/off/paused)
Radiometer Screen
oAllows the user to view and store irradiance readings
measured by the radiometer.
Phototherapy Report Screen
oAllows export of the phototherapy report to a USB
flash drive.

Page | 10
BiliLux LED Phototherapy Light
Configuration Screen
oAllows the user to adjust date, time, and language.
Device Status Screen
oDisplays LED usage in hours, firmware version, and inspection
dates.