Draper 218031 User manual

Assembly Instructions
Cinefold Portable Projection Screen by Draper
Frame Hinges and
hinge locks
Handy
Crank Viewing
Surface
KE
Adjustment
Knob
2" Min.
44" Max.
Anti-sway stabilizers
optional with HD legs
Standard
T-Leg
Frame
Snaps
Handy Crank Viewing
Surface
Bottom row of snap
studs to accept skirt
Standard T-Leg
Heavy duty legs optional
Frame/Screen Assembly
①Open carrying case and remove pouch containing screen surface, and
three aluminum assemblies. The largest package is the frame. Unwrap and
unfold it completely in one direction only, locking all hinges. Frame should
lie with snaps facing up.
②Remove surface from its envelope. With male snaps at bottom, snap
surface to frame. For easier surface attachment, start in one corner, then
work your way around the frame. Make sure snaps are secure.
Please note: For steps 3-5, screen should remain on floor or table, with
surface facing up. Carefully lift screen from floor or table to complete each
step.
③Lock corner braces.
④Unfold leg assemblies and lock hinges. Check that adjustment knob is in
the hole desired (upper for vertical screen position, lower for keystone
elimination). DO NOT unfold feet at this time.
⑤Attach legs to back side of vertical frame sections, as indicated by the
color coded markings, using Handy Cranks. For standard screen height,
match colored tapes exactly. Height is adjustable in 6" increments.
⑥Raise Cinefold to a vertical position and unfold feet. Tighten adjustment
knobs to maintain legs at desired angle. If your screen includes Heavy-
Duty Legs, unfold and lock the extensions on the backs of the feet, hinge
up to the backs of the leg, and attach with Handy Crank.
⑦If Anti-Sway stabilizers are supplied with your screen, refer to illustration
and attach with Handy Cranks.
A Note About Surfaces
①Always fold with snaps face-to-face. Do not permit screen fabric to
contact border material or snaps when folded. Store in pouch
provided.
②Take care at all times not to permit Cinefold viewing surface to contact any
dusty or dirty area, nor any varnished or painted object.
③When necessary, clean Cinefold viewing surface according to cleaning
instructions for the particular surface you are using.
Caution
①Read instructions through completely before proceeding; retain for future
reference.
②Handle viewing surface with care; do not allow it to come in contact with
sharp or dirty objects.
③Use Handy Cranks provided; failure to do so may lead to screen damage.
④Make sure screen is level.
⑤Do not write on viewing surface.
⑥The ideal temperature range for assembling folding screens to prevent
damaging the surface is 68°-78° F (20°-26° C). Assembling below
recommended temperatures may damage surface and void warranty.
Copyright © 2012 Draper Inc. Form Cinefold_Inst12 Printed in U.S.A.
®
Caution: Beware
of pinch points.
Caution: Make sure all hinges and joints are locked
before raising screen to standing position.
Caution: Make sure screen
is placed on level surface.
Warning: This product is intended for indoor use only. Failure to
follow warning may result in product damage or personal injury due to
unforeseen acts of nature.

Assembly Instructions
Truss-Style Cinefold Portable Projection Screen by Draper
Truss Assembly
①Remove pouch containing viewing surface from case and set aside.
Remove all aluminum assemblies.
②Unfold all folded aluminum assemblies completely, noting labels and
color-coded marks. Lock all hinges. Position Stage Right and Stage Left
sections in appropriate positions with snaps facing up. Top and Bottom
sections should be set with snaps facing down.
③To increase frame rigidity, hinges on top and bottom frame sections have
rivnuts marked with red and green. Insert a Handy Crank through the
threadless rivnut (red) and tighten into the threaded rivnut (green).
④Apply small sections marked “Stiffener Bars” to back of Bottom frame
section, using eight Handy Cranks each. Failure to use all Handy Cranks
may result in damage to screen frame. Turn Bottom frame section over so
snaps face up.
⑤If your screen frame is less than 25' wide, repeat step 4 for Top frame sec-
tion. Frames 25' wide and over are equipped with a special full-width Stiff-
ener for the top frame section. To attach it, place Stiffener flat with green
rivnuts face down. Place top frame section on top of and at right angles
to Stiffener, over the green rivnuts. Insert and tighten standard Handy
Cranks. Install 45° angle braces to the Top frame section and Stiffener with
short Handy Cranks. Turn Top frame so snaps face up.
Dress-Up Kit Assembly
PLEASE NOTE: All components are labeled and color coded to
facilitate assembly.
A. Valance Bar attaches to frame with simple bayonet-style mounting.
B. Draper Bars mount to Valance Bar, bayonet-style.
C. Optional adjustable Skirt Bar is secured to frame at desired level with
positive-locking plunger mechanism. If Skirt Bar is not used, Skirt may
be snapped to bottom of viewing surface.
D. Valance, Drapes, and Skirt snap onto Mounting Bars.
E. Gaps between the frame and the valance can be easily removed by
pulling the bottom edge of the valance to close the gap.
F. Pulling and smoothing the edges of the panels will remove any
wrinkles or puckers that might be present when product is unfolded.
Drapery
Bar
Valance Bar
Drapery
Bar
Adjustable Skirt Bar
Rigid
Truss
Frame
Anti-Sway
Stabilizers
Heavy-Duty
Legs
Frame & Legs
Assemble with
Handy Cranks
Handy Crank
⑥Join Top and Bottom to Stage Right and Stage Left, using two Handy
Cranks on each of the four corners. Match numbers on white labels, and
keep in mind that no Handy Crank should protrude outside screen frame.
⑦Remove surface from pouch. With the row of male snaps at bottom, posi-
tion screen surface over frame. Snap each of the four corners, then snap
across bottom, up sides, and across top.
⑧Attach feet to inner side of legs with Handy Cranks, matching color-coded
markings. Attach legs to Stage Right and Stage Left with Handy Cranks,
matching colored tapes.
⑨Raise screen to a vertical position. Add Heavy-Duty Legs and Anti-Sway
Stabilizers with Handy Cranks in the positions indicated below.
Copyright © 2012 Draper Inc. Form Cinefold_Inst12 Printed in U.S.A.
®
Caution: Make sure all hinges and joints are locked
before raising screen to standing position.
Caution:
Make sure
screen is placed
on level surface.
Caution:
Beware of
pinch points.
Caution
①Read instructions through completely before proceeding; retain for future
reference.
②Handle viewing surface with care; do not allow it to come in contact with
sharp or dirty objects.
③Use Handy Cranks provided; failure to do so may lead to screen damage.
④Make sure screen is level.
⑤Do not write on viewing surface.
⑥The ideal temperature range for assembling folding screens to prevent
damaging the surface is 68°-78° F (20°-26° C). Assembling below
recommended temperatures may damage surface and void warranty.
A Note About Surfaces
①Always fold with snaps face-to-face. Do not permit screen fabric to
contact border material or snaps when folded. Store in pouch
provided.
②Take care at all times not to permit Cinefold viewing surface to contact any
dusty or dirty area, nor any varnished or painted object.
③When necessary, clean Cinefold viewing surface according to cleaning
instructions for the particular surface you are using. Surface must be com-
pletely dry before folding.
Warning: This product is intended for indoor use only. Failure to
follow warning may result in product damage or personal injury due to
unforeseen acts of nature.