DREAMS 215-00945 User manual

215-00945 (Solid slats)
Knoxbed 215-00946 (Sprung slats)
Assembly Instructions
1. We suggest you spend a short time reading through this leaflet and then follow
the simple step by step instructions.
2. If you follow the instructions carefully the end result should be worth the effort.
3. Do not discard any of the packaging until you have checked that you
have all the parts and the pack of fittings.
4. Assemble this product on a carpet.
5. To ensure an easier assembly, we strongly advise that all fittings are only
finger tightened during initial assembly. Only upon completion of the.
Assembly should all fixing points be fully tightened.
6. We recommend a periodic check on all fixing points to make sure they remain
fully tightened.
7. Keep glue and fittings out of children s reach.
In the unlikely event that this product has missing or damaged parts, please call
03442 920000 to obtain spares
Before you
Start, here
are some
helpful
advices.
Revision number 1/1

M6x35mmx6 pcs
M3x35mmx1pc
M6nut x6pcs
M6 Washer x6 pcs
M4Allen key x 2pcs
M5Allen key x 1pc
Revision number 1/1
PARTS
Fittings
QTY
1
1
2
1
A
B
4
NO. PART LIST
(1) HEADBOARD
(2) FOOTBOARD
(3) WOODEN FEET
(4) SIDE RAILS
(5) SUPPORT LEG
F
Not included
G
Plastic Washer x 4pcs

ASSEMBLY
STEP 1
( ). Loosen the pre-assembled bolts
on the headboard and footboard
with the Allen Key(F)
Note: Leave 10 mm protruding as
in the diagram
Revision number 1/1
Plastic Washer x4pcs
F
M5 Allen key × 1pcs
G
F
(1). Attach the Wooden Feet to the
headboard and footboard by using
Plastic Washer (G) .
10mm

ASSEMBLY
STEP 2
(1). Attach the side rails to the
headboard and footboard.
Revision number 1/1

ASSEMBLY
STEP 3
MAKE CERTAIN THE BED IS
SQUARED UP .AS SHOWN ON
THE RIGHT.
Once all four comers are located.
make sure the bed is still square
as in the sketch.then tighten all
the bolts 100% using Allen key
(F).
Revision number 1/1
F
F
M5 Allen key × 1pcs

s
ASSEMBLY
STEP 4
NOTE: Slats not supplied shown
for reference only.
Both slats on "step 3" and "step
4" can be assembled to the
bedstead. You can make a choice
between the two slats.
OPTION"A": DREAMS FIXED
WOOD SLATS
（1）Carefully locate the slats
onto the unit. Fix one end
of slats.
（2）Use bolt (A) ,Washer (D)
and JCN nut (C) to fix the
unit using Allen Key (E) .
（3）Use Tapping Screw (B) to
fix the Support leg
（4）Fix all other slats.
（5）By hand insert adjustable
feet into each support leg
by turning clockwise.
Revision number 1/1
A
M6 × 35 mm x 6 pcs
B
M3 × 35 mm x 1 pc
C
M6 nut x 6 pcs
D
M6 Washer x6pcs
E
M4 Allen key × 2 pcs
E
C
A
E
D
E
C
A
E
D
B
Not included
E
C
A
E
D
10mm

ASSEMBLY
STEP 5
OPTION"B": DREAMS SPRUNG
SLATS
1) Use the bolt to fix support leg
onto the slat frame. Please note
that these bolts are to be found
inside the slat frame box.
2) Carefully locate the slats onto
the unit.
3) Use bolt (A) ,Washer (D) and
JCN nut (C) to fix the unit using
Allen Key (E)
Revision number 1/1
A
M6 × 35 mm x 6 pcs
C
M6 nut x 6 pcs
D
M6 Washer x6pcs
E
M4 Allen key × 2 pcs