DREAMS Seoul Sleepmotion 200i User manual

Parts Identification
Parts Checklist
Page 1 of 13
3
3
2
SEOUL LIFESTYLE TV BED
SLEEPMOTION 200i
1
456
78 9
Qty Qty
Ref. Description DescriptionRef.
1
2
3
1
1
2
4
5
6
7
8
9
Headboard
190112
Footboard
Side Rails
5
5
1
1
1
1
PLEASE NOTE:
TO CONTROL THE BED VIA AN APP, PLEASE GO TO THE APP STORE OR GOOGLE PLAY AND DOWNLOAD THE
'NAPP BY DREAMS'.
ONCE DOWNLOADED AND REGISTERED 'ADD DEVICE' THEN FOLLOW THE INSTRUCTIONS.
ONCE CONNECTED YOU WILL BE ABLE TO CONTROL THE TV LIFT VIA NAPP BY DREAMS.
OCASSIONALLY, DUE TO ATMOSPHERIC CONDITIONS OR WHEN RE-PLACING THE REMOTE CONTROL, ONE
NEEDS TO RE-PAIR THE SYSTEM:
1) TURN OFF ALL POWER.
2) PRESS UP OR DOWN SWITCH ON TV BED REMOTE KEEPING IT PRESSED.
3) TURN POWER BACK ON.
EITHER THE TV BED REMOTE CONTROL OR THE NAPP CAN BE USED TO RAISE OR LOWER THE TV LIFT.
BEFORE STARTING ASSEMBLY PLEASE REFER TO THE OWNERS MANUAL
SUPPLIED WITH YOUR SLEEPMOTION 200i BED BASE AND FOLLOW THE
INSTRUCTIONS TAKING NOTE OF ANY SAFETY PRECAUTIONS OR
OPERATIONAL SAFETY REQUIREMENTS OF THE INSTALLATION.
BUILD THE BED BASE FIRST USING ONLY THE EIGHT LONGER LEGS
6" (15 cm), SEE STAGE 1.
IMPORTANT: PLACE THE BASE IN FINAL POSITION IN THE ROOM OF USE, CONNECT THE POWER AND CHECK
THE OPERATION THEN STEP BY STEP FOLLOW THE TV BED ASSEMBLY INSTRUCTIONS BELOW, TO BUILD THE
TV BED AROUND THE SLEEPMOTION 200i BED BASE.
PARTS SHOWN IN DOTTED LINES ARE PACKED IN THE SLEEPMOTION BED BASE CARTON
10
TV
Installation
Kit
Pack Inside
accessory
box in
footboard
Pack 2
10 1
Mains Power Lead - 3 mt
Aerial Lead - 4 mt
HDMI Lead - 5 mt
Cable Clips
Cable Ties
TV Lift Remote Control
TV Installation Kit

Fittings Checklist
Page 2 of 13
In the unlikely event of missing or damaged parts, please
contact the customer service team on 0344 292 00 00.
When calling this number, please quote the part code
reference numbers shown in this leaflet when
requesting spare or replacement parts.
Please retain your assembly instruction and
tools provided for future use.
Periodically check that all bolts are still tight.
Additional Tools Required
General Hints & Tips When they are supplied and are
part of the assembly of this bed,
ensure that the barrel nuts are
fitted the correct way so the
hole in the nut is facing towards
the intersecting hole in the panel.
Intersecting
Hole
Care & Maintenance
We recommend the bed is
assembled in
the room it shall be
located in.
A ssembly requires two persons.
Approximate time to
assemble this product
1.5
HRS
Stage
1
Screw in the Legs and put Bed Base in the position in which it will be used
x8
A
x16 C
x16
Spring Washers (for M8 bolts) D
Flat Washers (for M8 bolts)
BAllen Key (for M8 bolt)
x1
Bolts (M8x30mm) for
fitting side rails (3&4)
)2&1(draobtoof&draobdaehot
x16
HARDWARE NEEDED FOR FIXING SIDE RAILS TO HEADBOARD & FOOTBOARD
PACKED IN SIDE RAIL PACK 3 - HARDWARE PACK (A)
Tape Measure
Qty QtyRef Description DescriptionRef.

1
Page 3 of 13
Stage
2
Stage
3
Prepare the Head & Foot Ends for assembly
AD
B
C
10mm
Ax8 Bx8 Cx8
D
x1
2
1
1
3
Ax4 Bx4
Cx4
D
x1
A
B
CD
90%
1
3
Assemble Head End and one Side Rail using hardware Pack 'A'
10mm
20mm
1
3

Position Foot End and connect Side Rail brackets..
Page 4 of 13
Stage
4
Stage
5
Ax4 Bx4 Cx4
D
x1
2
90%
2
3
Raise the Head and Foot Ends of the Bed Base
D A BC

Stage
7
Page 5 of 13
Electrical & Cable Connections
Stage
6
4
Connect Main Power Lead (4) to
your wall socket - for safety this
must be an earthed power supply.
Press the “UP”
button to raise
the TV lift.
9

8
Page 6 of 13
Stage
TIP:
BEFORE FITTING THE TV,
PUSH CABLES THROUGH
EACH DUCT FROM THE TOP.
CHOOSE THE BEST SIDE TO
USE DEPENDING ON WHERE
THE CONNECTION PORTS
ARE ON BACK OF YOUR TV.
NEVER CROSS CABLES FROM
ONE SIDE TO THE OTHER.
Note: For illustration purposes
only, TV connections may vary.
TV Power Lead
supplied with your TV
5
6

Page 7 of 13
a
a
Loosen Tighten
b
Stage
9
a x2
b x2
Screw-Washer sets
(M8x25mm) Use
5mm Allen Key (D)
Counter-Sunk Screws
(M6x12mm)
Counter-Sunk
Screws (M4x12mm)
Allen Key (4mm) Allen Key (2.5mm)
IF SCREWS ARE SUPPLIED WITH TV, PLEASE USE THOSE IN PREFERENCE
TV Installation - Normal Vesa Fixing

Stage
10a
Stage
10b
Page 8 of 13
TV Installation - Vesa 100x100
aa
b
100mm
100mm
REMOVE CROSS-BRACKET
AND FIX DIRECTLY TO BACK OF TV
a x2
b x2
Screw-Washer sets
(M8x25mm) Use
5mm Allen Key (D)
Counter-Sunk Screws
(M6x12mm)
Counter-Sunk
Screws (M4x12mm)
Allen Key (4mm) Allen Key (2.5mm)
IF SCREWS ARE SUPPLIED WITH TV, PLEASE USE THOSE IN PREFERENCE

TV Installation - Vesa 100x100
Stage
10c
Page 9 of 13
Loosen Tighten
i.
ii.

Page 10 of 13
Electrical & Cable Connections
Stage
11
Note: For illustration purposes
only, TV connections may vary.
TV Power Lead
supplied with your TV
PLUG IN - KEEP ALL CABLES
TIGHT - USE CLIPS & TIES
PROVIDED.
Keep wires tight - peel
off cover from cable clips
& adhere to back of TV.
8
6
5
7