DREAMS JEMMA 3 User manual

JEMMA 3'
Assembly Instructions Date: 27-03-2008
Do not throw away any of the packing or the instruction book until you have checked all the
components and fittings and the furniture is fully assembled.
In the unlikely event that this product has missing or damaged parts, please call 0870 3333 612 to
obtain spares. Page 1 of 6
1000mm
Jemma 3'
2020mm
982mm

Components parts and fittings contained in the box
Please sort out all parts before you begin to assemble the item. This to make sure you always use the correct part.
Fittings
Hazard Warning !
Keep small components out of the reach of children.
Parts
AB1 pc. Allen key - 4mm C
D
8 pcs. - Bolt M8 x 15 mm
E
6 pcs. - Flat Washer Ø6 x Ø20mm
F
4 pcs. - Lock Washer Ø8 x Ø12mm
G
4 pcs. - Bolt M6 x 50 mm 4 pcs. - Sleeve Nut M6 x 15 mm
6 pcs. - Screw Ø4 x 40mm
309 / 0002
304 / 0047 409 / 0005
409 / 0006 304 / 0055 408 / 0003
302 / 0038
12
3
Headboard
1 pc.
Footboard
1 pc.
Siderail
2 pcs.
1000 x 982mm
700 x 982mm
1900 x 115mm
219 / 0071 219 / 0072
108 / 0088
Page 2 of 6 Jemma 3'

Key diagram and tools needed.
Key diagram.
Tools needed.
1
2
3
3
Page 3 of 6 Jemma 3'

Assembly
Step 1
Fix the siderails "3" to the
headboard "1" using bolts
"A" as shown.
Tighten the bolts using the
allen key "B".
Step 2
Fix the footboard "2" to the
siderail using bolts "A" as
shown.
Tighten the bolts using the
allen key "B".
B
A
A
1
2
1
3
3
3
3
A
A
A
Page 4 of 6 Jemma 3'

Assembly
Step 3
DREAMS SPRUNG SLAT
SYSTEM
Open the metal Slat
Frame outwards.
Turn the metal Slat Frame
falling upward and
carefully lower the Slat
frame into the bed.
Ensure that the frame sits
on the guides located on
the Side Rails "3".
Position the Slat Frame so
that the holes in the Frame
align with those in the Side
Rails "3". Secure the
Frame to the Side Rails "3"
by threading Bolt "E"
through Lock Washer "D"
and Washer "C" and
through the holes in the
frame and the Side Rails
"3".
Finally, tighten the Bolt "E"
into the sleeve nut "F" from
the top of slat frame.
Step3
F
C
D
E
B
ED
C
ED
C
ED
C
ED
C
3
3
3
FIXED WOOD SLATS
Place the Fixed Wood
Slats onto the slatholders
on siderail "3".
Fix the slats at both ends
and the middle using
screws "G" and washer
"C". Total of six screws
and washers.
3
G
G
CC
G
G
Page 5 of 6 Jemma 3'

Assembly
Please note that the product you have purchased is a natural living timber.
Just like nature itself, wood varies in shape and colour. Knots, vein patterns, resin pockets and
colour differences contribute to giving the piece of furniture its beauty and form a natural part of
solid wood.
Although the tree has been cut down and dried, it is still alive and therefore will react to high and
low temperatures, light, humidity, drought and time.
In cold and dry periods, the wood contracts which may lead to small cracks in the piece of
furniture. The reverse happens in warm and humid periods where the wood expands and this may
result in slight unevenness.
The colour of the wood also changes with time, particularly if the furniture is place in a light place.
This is natural process and part of owning a piece of furniture made of solid wood.
Any flexing that has occurred during transport will re-correct it self once this product is correctly
assembled.
Tighten all joins of furniture after six months. Please keep these instructions in a safe place for
future use.
Dear customer.
Page 6 of 6 Jemma 3'