DREAMS Deacon Ottoman User manual

Deacon Ottoman bed
Assembly Instructions
1. We suggest you spend a short time reading through this leaflet and then follow
the simple step by step instructions.
2. If you follow the instructions carefully the end result should be worth the effort.
3. Do not discard any of the packaging until you have checked that you
have all the parts and the pack of fittings.
4. Assemble this product on a carpet.
5. To ensure an easier assembly, we strongly advise that all fittings are only
finger tightened during initial assembly. Only upon completion of the.
Assembly should all fixing points be fully tightened.
6. We recommend a periodic check on all fixing points to make sure they remain
fully tightened.
7. Keep glue and fittings out of children s reach.
In the unlikely event that this product has missing or damaged parts, please call
03442 920000 to obtain spares
Minimum No.of people
recommended to assemble
this product:
Approx assembly time:
2
hour
1
Before you
Start, here
are some
helpful
advices.
Revision number 1/1

Revision number1/1
PARTS
Fittings
QTY
1
1
4
2
2
NO. PARTLIST
(1) HEADBOARD
(2) FOOTBOARD
(3) SIDE RAILS ( R&L)
(4) SUPPORT BRACKETS
(5) BOTTOM BOARD
(6 ) SLATTED BED FRAME ( R&L)
(7 ) JOINING BRACKETS
(8) MATTRESS HOLDER
(9) FABRIC PULL HANDLE
2
2
2
1

ASSEMBLY
STEP1
(2). Attach the side rails to the
headboard and footboard.
Note: Leave10mmprotruding as
in thediagram
Revision number1/1
(1). Loosen thepre-assembled bolts
ontheheadboard and footboard
withtheAllen Key (J) (K) .

ASSEMBLY
STEP2
Revision number1/1
MAKE CERTAINTHE BED IS
SQUARED UP.AS SHOWNON
THE RIGHT.
Onceallfour comers arelocated.
makesurethebed isstillsquare
asinthesketch.then tighten all
thebolts100%usingAllen key
(J)(K)

ASSEMBLY
STEP3
Revision number1/1
(1). Attach the support brackets
to the headboard and
footboard by using bolts (A) ,
washer (H) and allen key (K).

ASSEMBLY
STEP4
Revision number1/1
(1). Fix the bottom boards

ASSEMBLY
STEP5
1) Join the two halves together using
the bolt (B) through the holes
and tighten with the M8 nut.
Revision number1/1
2)Slot the bolts (C) through the
holes and tighten with the M6 JCN
nuts. Complete at head and foot
end of frame.
3)Push the two mattress bars into
the holes both sides of the head
end of the frame.

ASSEMBLY
STEP 6
1) While one person holds the slatted
frame up, the second person must fit
the gas strut to the hinge.
2) One end of the strut will already be
attached to the hinge. At the other
end, take the nut off the bolt and
attach the other end of the strut.
3) Once this is in place, replace and
tighten the nut.
4)Repeat process for the other side
of the bed.
Revision number 1/1
1) Identify the head end of your
slatted frame, this will be the end with
holes.
2) Carefully lower the slatted frame
into the base so that it rests on the
hinges and the support brackets.
Again, this will require two people to
do safely.
3) Align the holes on the frame with
the holes on the hinge and pass the
three bolts (D) through the washers
provided and then into the holes each
side of the frame.
4) Place a nut onto each of the M6
bolts and tighten with fingers, then,
using the Allen key provided, fully
tighten.
5) Attach the Fabric Pull Handle
at the end of slat frame.
6) The slatted frame and base are
now joined.
NOTE: When fully assembled and the
mattress is in position, please
raise and lower the ottoman 5
times. To ensure the gas
pistons are fully lubricated.