DREAMS LUCIA User manual

7
6
9
10
8
7
12 12
13
11 11
11
3
1
2
3
11
Drawer
Side Rail (single)
6Drawer Front Panel 1
Drawer Side Panel 2
7
8Drawer Front Panel ii 1
9Drawer Bottom Panel 1
Ref.Qty
Ref.Description
10 Drawer Back Panel 1
11 Adjustable Support Leg 2
12 Bottom Support Rails 2
13 Bottom Support Rails 1
5Metal Sprung Slat System* 1 frame
Side Rails For
Single Drawer
LUCIA STORAGE BED
Parts Identification
PLEASE READ
this sheet prior to assembly to familiarise
yourself with the various stages of construction. Carefully
open the hardware packs supplied and check the contents
against the parts and fittings check list.
Do not destroy any of the packaging until you are certain
that you have all the necessary parts for the assembly.
Please ensure that the packaging is disposed of in a
safe environmentally friendly way.
CAUTION: There are small components used in the
construction of this unit. These loose items should be kept
a way from young children whilst assembling your unit to
avoid the danger of choking hazards.
Qty
1
2
3
3
3a
Headboard
Footboard
Side Rail (double)
1
1
2
1
Side Rail (single) 1
Parts Checklist
Description
45
4Wooden Slats 1 set
Note:
Standard wooden slat frame (part 4)
Upgraded sprung slat frame (part 5)
*Only supplied if upgraded sprung system chosen
NOTE THAT ON BEDS SUPPLIED WITH TWO DRAWERS, THERE WILL BE A SET OF PARTS
FOR EACH DRAWER. THESE WILL BE SUPPLIED IN THE DRAWER FITTINGS PACK.
Page 1 of 6
3
3a

(single)
(Single)
(Single)
(Single)
(Single)
(Single)
QtyCode Description
In the unlikely event of missing or damaged parts, please
contact the customer service team on 08442 920000.
When calling this number, please quote the part code
reference numbers shown in this leaflet, to properly
identify spare or replacement parts.
Please
retain your assembly
instruction & tools for future use.
This
assembly
requires two
people.
Ax16
Bolt (M8x30mm)
Fittings Checklist
C
x16
Spring Washer
D
x20
Washer (17x8mm) (Double)
Additional Tools Required
Hx1
Allen Key (4mm)
Fx6
Sleeve Nut (M6x16mm)
Qty
Code Description
B
Bolt (M6x40mm)x6
General Hints & Tips When
fitting barrel nuts into
the panels, ensure they are
fitted the correct way so the
hole is facing towards the
intersecting hole.
Intersecting
Hole
Care & Maintenance
Crosshead Screwdriver
We recommend the bed is
assembled in the room it will
be located in.
K
x6
Washer (16x6mm)
G
Plastic Nut (Double) x28
E
Allen Key (5mm) x1
PBolt (M6x15mm) x8
Note: The following fittings will be found in the box which contains the sprung slat frame. They are not in the assembly
kit for the bed itself.
Q
Support Legs
R
Centre Support Leg
x2
x1
Screw (3x20mm) (Double) x40
I
JScrew (5x50mm) (Double) x28
LScrew (4x30mm) (Double) x16
MBolt (M8x45mm) (Double)
x4
NAdjustable leg (Double) x4
OWheel (Double) x10
(Single)
x5
x14
x14
(Single)
x20
x8
x2
x24
x8
Page 2 of 6

A: Double B: Single
1
rails
ARROWS ON LABELS
POINT TO EACH OTHER
Bed Assembly
Stage
1
A: Double
Fit the bolts (A), spring washers (B), and washers (C) to the holes in the headboard (1) and footboard
(2) as shown. Note: Do not fully locate the bolts, but leave 10mm protruding.
Fit the side rails (3) to the headboard and footboards locating the brackets over the bolt heads.
Once all four corners are located check the bed is square, then fully tighten the bolts using the allen key (D).
B: Single
Fit the bolts (A), spring washers (B), and washers (C) to the holes in the headboard (1) and footboard
(2) as shown. Note: Do not fully locate the bolts, but leave 10mm protruding.
When bed with only one drawer is purchased, choose which side you want the drawer then fit the side
(3 & 3a) to the headboard and footboard locating the brackets over the bolt heads.
Once all four corners are located check the bed is square, then fully tighten the bolts using the allen key (D).
A
B
C
10mm
Stage
2
1
2
3
1
2
3
3a
B: Single Bed
3
N
C
M
11
A: Double/King Bed
Ax8 Bx8 Cx8
MC
Double: x8
Single: x4
Double: x8
Single: x4
3
3
3a
A: Fixing adjustable legs (11) to side rails (3). Fix support legs from inside the bed frame into pre-threaded holes.
B: Fixing adjustable legs (11) to side rail (3a). Fix support legs from inside the bed frame into pre-threaded holes.
Page 3 of 6
3a
3
&

(E, F & G).
Use all of the x6 bolt sets provided
Use x4 of the x6 bolt sets provided (E, F & G).
Bed Assembly
Stage
3a UPGRADE SPRUNG SLAT SYSTEM
5
5
Gx4
Fx4
Ex4
Px8
5
R
Q
R
Stage
3BED SLAT FIXING Gx6
Fx6
Ex6
4
4
Lay the set of slats (4) onto the slat
support rails on the side rails.
Align the first and last slat with the
end of the rails, and secure in place
using the bolts (E), washers (G) and
sleeve nuts (F). Fully tighten using
the allen key (H).
Once secure fix the centre slat using
the bolts as before.
Open the metal frame and lay face down on the working
surface.
Fit the support legs (Q & R) to the positions shown, securing
with the bolts (P). Fully tighten using the allen key (H).
Carefully turn the slat frame over, and position onto the slat
support rails. Align the frame with the fixing holes at each
end and secure using the bolts (E), washers (G) and slee ve
nuts (F). Fully tighten using the allen key (H).
Finally, please ensure that all bolts are fully tightened
before the bed is used.
ONLY ONE OF 4 OR 5 WILL BE SUPPLIED SEPARATELY
4
5
Page 4 of 6

Step 2:
Step 3:
12
13 K
O
Bed Assembly
Stage
4DRAWER ASSEMBLY
J
I
7
Step 1:
IMPORTANT:
MAKE SURE WHEN YOU
FIT THE NUTS THAT
THE HOLE IS IN THE
CORRECT ALIGNMENT
J
I
J+I
I
I
12
J
I
Double: x12
Single: x6
Double: x12
Single: x6
Stage
5
10
7
7
J
J
I
Double: x16
Single: x8
Double: x16
Single: x8
K
O
Double: x40
Single: x20
Double: x10
Single: x5
7
9
13
J
12
Page 5 of 6
8
8

Bed Assembly
Stage
6DRAWER ASSEMBLY
Stage
7
LDouble: x16
Single: x8
SLOT IN THE DRAWERS
6
FOLLOW LINE ON BACK OF
DRAWER FRONT PANEL
L
Page 6 of 6