DREAMS KINGSBURY BED User manual

helpful advice
is some
start,here
Before you
234-00001 (Sprung slats)
SMALL DOUBLE 234-00000 (Solid slats)
235-00128 (Sprung slats)
KINGSBURY BED KING 235-00027 (Solid slats)
231-00028 (Sprung slats)
this product
Approx assembly time
recommended to assemble
Minimum No.of people
DOUBLE 231-00027 (Solid slats)
We suggest you spend a short time reading through this leaflet and1. then follow the simple step by step instructions.
If you follow the instructions carefully the end result should be worth2. the effort.
Do not discard any of the packaging until you have checked that you3. have all the parts and the pack of fittings.
To ensure an easier assembly, we strongly advise that all fittings are4. only finger tightened during initial assembly. Only upon completion of
the. Assembly should all fixing points be fully tightened.
We recommend a periodic check on all fixing points to make sure they5. remain fully tightened.
Keep glue and fittings out of children’s reach.6. In the unlikely event that this product has missing or damaged parts,7. please call 0844 292 0000 to obtain spares
Page 1 of 6
Assembly Instruction

G
Center leg x 1pc.
A
B
M6 x 6pcs.
IK
M6 x 12mm x 8pcs.
Allen key 4mm x 2pcs.
C
D
M6 x 38mm x 6pcs.
E
M6 x 22mm x 4pcs.
G
Center leg x 2pcs.
C
Allen key 4mm x 1pc.
M8 x 20mm x 8pcs.
Ø3.5 x 25mm x 2pcs.
F
Ø4 x 40mm x 6pcs.
H
M8 x 4pcs.
Page 2 of 6
Note:The following fittings will be found in the box which contains the Sprung
Frame, NOT with the bed frames Assembly Kit.
PLEASE DO NOT USE THE FOLLOWING HARDWARE FOR THIS BED!
2(1 piece)
4(1 piece)
1(1 piece)
3(2 pieces)
5(2 pieces)
PARTS Fittings

4
5
5
Cx1
Dx2
Page 3 of 6
1
2
3
3
Ax8
Fix the side rails "3" to the
headboard "1" and
footboard "2".
Use bolts "A", tighten using
allen key "C".
Cx1
Attach central support "4"
to support feet "5".
Use bolts "D", tighten
using allen key "C".
Assembly

7mm
Page 4 of 6
1
2
3
3
Bx2
4
5
IMPORTANT
Once the feet have been
assembled and attached,
they should be adjusted to
ensure they do not touch
the floor, (7mm above the
floor) to allow for movement
once the mattress is placed
on the bed frame.
It is important to note that
when moving the bed that
it is not dragged into its new
position to prevent the
possibility of these feet
being twisted or angled to
one side, which could lead
to the collapse of the centre
of the bed.
To move the bed, remove
the mattress and lift the bed
into its new position to avoid
damage.
Ensure the feet are at 90 to
the floor before replacing
the mattress.
Place the fixed central
support "4" onto the support
block on headboard "1" and
footboard "2".
Fix the central support "4"
at both ends using screws
"B", tighten with a
screwdriver.

Option 1:
Dreams solid slats
Place the fixed wood slats
onto the slat holders on
side rails "3".
Fix the slats at both ends
and the middle using screws
"F" and washers "G", tighten
with a screwdriver. total of
six screws and washers.
Open the metal slat frame
outwards.
Option 2:
Dreams sprung slat frame
Important Note: Your
Bedstead comes supplied as
standard with Solid Wood
Slats, or upgrade available to
Sprung Slat System at point
of purchase at an additional
cost.
Please carefully follow the
correct assembly instructions
for the slat system that you
have purchased. 1
2
3
3
Fx6
Gx6
Page 5 of 6

Turn the metal slat frame
falling upward and
carefully lower the slat
frame into the bed.
Ensure that the frame sits
on the guides located on
the side rails "3".
Position the slat frame so
that the holes in the frame
align with those in the side
rails "3".
Secure the frame to the side
rails "3" by threading bolt
"D", washers "G" and
through the holes in the
frame and the side rails "3".
Finally, tighten the bolt "D"
and washers "G" into the
sleeve nut "E" and washers
"H" from the top of slat
frame with allen keys "C".
1
2
3
3
Page 6 of 6
Cx1
Dx4
Ex4
Cx1
Hx4
Gx4