Drive DeVilbiss Healthcare BTR22BLK User manual

Bariatric Steel Transport Chair
(BTR22BLK)
Instructions for use

Page 2 of 12BTR22BLK Wheelchair (2021-12 Rev1)
Introduction
Intended purpose
To provide manually propelled mobility to an individual who has a walking
related disability and/or who does not have the full capacity to walk.
Intended user group
The wheelchair is intended for an individual who has a walking related
disability and/or who does not have the full capacity to walk and has a weight
of up to 200kg (31 stone).
Environment of use
The wheelchair is suitable for both indoor and outdoor use however it is not
intended to be used on rough or uneven terrain.
Indications
To assist with the mobility of an individual, as defined in the ‘intended user
group’ section.
Contraindications
• The occupant exceeds the maximum weight capacity.
• The occupant has postural support needs that are not addressed by
the wheelchair.
• Inability to safely guide a wheelchair (only applies to self propelled
variants).
• Occupants with Hemiplegia (only applies to self propelled variants).
• Occupants with only one arm/hand (only applies to self propelled
variants).
Other contraindications may be relevant which are specific to an individual
and / or care environment.
Product overview
The wheelchair is constructed from a tubular steel frame with a padded fabric
seat for the occupant. The wheelchair incorporates footrests for the occupant,
and it is able to be folded when not in use or being transported in a vehicle.
The wheelchair is available as a transit model, where an attendant is required
to propel it. The wheelchair can be manually propelled forwards and
backwards.

Parts description
SIDE
PANEL
FOOT
REST
FRONT
CASTOR
REAR
TRANSIT
WHEEL
PUSH
HANDLE
BACKREST ARM REST
PARKING
BRAKE
STEPPER
TUBE
BTR22BLK Wheelchair (2021-12 Rev1) Page 3 of 12

symbolsPreparing for use
BTR22BLK Wheelchair (2021-12 Rev1) Page 4 of 12
Using Parking Brakes
To apply the parking brakes, push the handle
on the brake unit until locked in place. To
release the brake, push the handle in the
opposite direction. The brakes should always
be applied when the wheelchair is stationary.
Note: The brake on your wheelchair model
may be visually dierent from that shown.
Operating
parking
brakes
These instructions should be read carefully before using the wheelchair.
This product does not have a service manual. The only parts for user
assembly are the footrests.
A risk assessment must also be performed to assess suitability of the device
for the user. This assessment should include, but not be limited to:
• Small adults (and children)
• Users (and attendants) who lack capacity
• Very active occupants
• Unauthorised access to the wheelchair
Independent users and attendants are responsible for determining that they
are both mentally and physically capable of using the wheelchair with
minimal risk of harm.
Maximum occupant mass
Exceeding the maximum occupant mass marked on your device can damage
the product and put users at risk of harm.
Remove all packaging and stand the wheelchair on the ground. Separate the
arm rests to open the wheelchair, then push down firmly. Once the seat is
secure, the backrest is upright and the footrests are attached (see overleaf),
the wheelchair is ready for use.
!
Warning
This wheelchair must not be used as a seat in a motor vehicle.
Users should always transfer to the vehicle's seat and the
wheelchair should be safely stowed away.

BTR22BLK Wheelchair (2021-12 Rev1) Page 5 of 12
footrest adjustment
!
Common misuse
Do not stand on the footrests. Overloading can damage the
product and cause harm to the occupant.
It is important to attain the correct leg position for
optimum comfort.
Press the brass buttons (left) and adjust to the
desired height.
Release the buttons and keep adjusting the
footrest until it locks in position with an audible
click.
Fitting and Altering the Footrests
To fit the footrests, place them on the two receiver
posts on the frame. Swing them inwards until they
lock in position.
To remove, press the chrome lever whilst swinging
the footrest out (shown left).
Adjusting
the footrest
Armrest removal
To remove the armrest, press the
chrome button at the front of the
armrest (arrowed) and pull up on the
armrest.
To replace the armrest, push the
armrest back into the receivers and
it will automatically lock.

Page 6 of 12BTR22BLK Wheelchair (2021-12 Rev1)
Transfer and use
!
Before using the wheelchair, read the safety notices below;
• Do not exceed the 10º maximum gradient. Use slow speeds
and do not reverse down a gradient.
• Do not use on escalators.
• The wheelchair is only suitable for single occupancy.
• Keep your feet on the footrests when moving. Do not stand on
the footrests. Overloading can cause harm to the occupant.
• Ensure that fingers and objects do not get caught in the wheel
spokes or any other moving parts during use and assembly.
• Maintain proper balance at all times. Users should not move
their centre of gravity out of the seating area or reach further
than their arm’s length.
• Parking brakes should always be applied when transferring.
• Be aware of hazards in your environment, such as narrow
doorways, steps, household appliances, children’s toys, etc.
• A risk assessment must be performed by a competent person
to ensure the wheelchair is suitable for the user. Consult a
healthcare professional before using assistive medical devices.
• Keep away from heating and ignition sources which may raise
surface temperatures or cause a fire.
Transfer: When transferring in and out of the seat, move the seats as
close as possible to each other. Attendants should always engage parking
brakes during transfer and fold away footrests. If required, attendants are
responsible for being suitably trained and competent to lift occupants with
minimal risk of harm. Good health and safety practice must always be used.
Propelling: Only attendants can propel this wheelchair. Push from behind
using the handgrips, and following the safety advice above. To slow down,
apply reverse pressure to the push handles.
When stationary, the brakes should always be applied.
Using a wheelchair belt
Belts are often used to restrain wheelchair occupants during normal use.
However, belts are not necessary parts of this device. Any belts used should
be adjusted to suit each user. When fastened, they should be tight without
causing discomfort or undue pressure. Belts may not be suitable for all users.
Seek professional medical advice before using a wheelchair belt.

Page 7 of 12BTR22BLK Wheelchair (2021-12 Rev1)
Steep terrain, kerbs and steps
Steep terrain: These wheelchairs are not designed for use on gradients
beyond 10°. When on a slope, avoid swerving or sudden changes in direction.
Over kerbs: Attendants push down on the stepper tube with a foot to
raise the front castors (when mounting a kerb for example).
To mount, approach the kerb head-on. The attendant uses the stepper tube to
raise the front castors, and lower the front castors on the raised kerb. Then
push the wheelchair forward, lifting it up slightly to mount the kerb if required.
To go down, align the front castors with the kerb edge. Using the tube to keep
the castors raised, tip the user slightly back and slowly lower the wheelchair.
!
Common misuse
Do not lean or push down on the push handles, as this can
damage the wheelchair.
!
Warning
When going down a kerb, the front castors must be raised to
prevent the user from falling out. The above are only
recommendations and may not be suitable for all events.
Multiple steps: The wheelchair is not designed to mount staircases, so may
require carrying if no elevators or ramps are available. Attendants are
responsible for being suitably trained and competent to lift the wheelchair with
minimal risk of harm. Do not carry using the handles or any removable sections.
Folding and storage
This wheelchair is easily foldable to minimise storage space required. The
footrests may be either folded up and swung outwards, or removed by
following the steps in footrest adjustment.
To fold the wheelchair, grab the centre of the front and rear edges of the seat
sling. Pull upwards on the seat canvas and the wheelchair should naturally
fold up. Adopt the latest health and safety recommendations when lifting.
Store in a dry environment, away from direct sunlight with parking brakes on.
Note: The wheelchair may be folded and stored in a motor vehicle.

Page 8 of 12BTR22BLK Wheelchair (2021-12 Rev1)
Care and maintenance
Do not use a damaged or badly worn wheelchair. Users should routinely check for
any malfunctions or changes in performance. Contact Drive DeVilbiss Healthcare
Ltd or your provider to replace damaged or worn parts.
• Brakes and tyres should be checked before each use, and at least once a month.
• The wheelchair should be kept dust free and cleaned at least once a week.
Upholstery and tyres can be cleaned with a damp cloth and mild soap solution.
Avoid neat bleach or abrasive surface cleaners. Leave to fully dry before reuse.
Metal parts should also be polished once a month with an auto wax. Replace
worn or torn upholstery promptly, as it may not support your body weight.
• Drive DeVilbiss Healthcare Ltd recommend that an approved service engineer
maintains the wheelchair annually, and these items should be repaired,
replaced, adjusted and/or lubricated if required:
•When the product has reached the end of its useful life, follow local recycling
and disposal policies.
• Tyres and castors
• Wheel bearings
•
•
Brakes
•
Footrest locking mechanism
Seat upholstery
•
•
Back upholstery
•
Arm pads
•
Wheelchair folding mechanism
Back posts
Powerpack installation
This wheelchair is suitable for some retrofit
powerpacks, which allow the device to be
controlled electronically. (See Powerpack
example image.)
Powerpacks are not required to use the
wheelchair. The mounting position will need
adapting to be suitable for both the user and the
powerpack used. Any installed powerpack must
be used in line with the manufacturer’s instructions
for use.
For more information about powerpacks, contact
Drive DeVilbiss Healthcare Ltd or your local dealer.
Powerpack
example

BTR22BLK Wheelchair (2021-12 Rev1) Page 9 of 12
Warranty
Your Drive branded product is warranted to be free of defects in materials
and workmanship for one year from date of purchase. This device was built to
exacting standards and carefully inspected prior to shipment. This warranty is
an expression of our confidence in the materials and workmanship of our
products and our assurance to the customer.
In the event of a defect covered by this warranty, we will at our option supply
parts or replace the device. This warranty does not cover device failure due
to owner misuse or negligence, or normal wear and tear. The warranty does
not extend to non-durable components, such as rubber accessories, castors
and grips, which are subject to normal wear and need periodic replacement.
The wheelchair frame has a 5-year warranty.
If you have queries or require full warranty conditions, contact your provider.
Accessories and spare parts
Drive DeVilbiss Healthcare Ltd provide accessories and spare parts for the
wheelchairs in this range. To order these parts, contact your provider. Visit
www.drivedevilbiss.co.uk to find your local stockist. Spare part catalogues,
compatibility charts and other documentation can also be found on this
website. Only use parts approved by Drive DeVilbiss Healthcare Ltd.

specification
Specification
Model BTR22BLK
Maximum occupant mass 200 kg
Overall length with footrest 104 cm
Overall width 71 cm
Armrest height 71 cm
Total mass 16.2 kg
Static stability 10°
44 cm
56 cm
Seat surface height at front edge 52 cm
Overall height 92 cm
BTR22BLK Wheelchair (2021-12 Rev1) Page 10 of 12