DT Research DT307SQ Assembly instructions

DT307SQ
ENGLISH
Mobile POS Tablet
BASIC OPERATION GUIDE
DT307SQ
ENGLISH 4
signage dtri com
DT Research, Inc.
2000 Concourse Drive, San Jose, CA 95131
Copyright © 2016, DT Research, Inc. All Rights Reserved. BOGW091316DT307SQENG
INTRODUCTION
Thank you for acquiring the DT307SQ Mobile Tablet. The DT307SQ offers a 7”capacive
touch display in a compact, rugged, and lightweight package. The DT307SQ enables
efficient point-of-service/sales applicaons, inventory management, and field services.
The DT307SQ provides the precise features needed to streamline operaons and improve
producvity, data accuracy, and service.
PACKAGE CONTENTS
One DT307SQ•
One Baery Pack and Handstrap•
AC-DC Power Adapter•
Basic Operaon Guide•
*The actual package contents may vary depending on the configuraon acquired.
PRECAUTIONS
Always exercise care when operang and handling the DT307SQ.•
Do not disassemble any poron of the DT307SQ, as this will void any product warranty.•
Do not use any power adapter or charging cradle other than the one provided with the•
tablet or acquired from the manufacturer or its partners.
In the unlikely event that abnormal noise, strange odor, or smoke is present, immedi-•
ately power down the DT307SQ and disconnect all power sources. Please report the
problem to your device provider immediately.
MSR/ RFID Reader Module
Enable and disable MSR/ RFID Reader module, and set up the parse data format:
Launch Keyboard Wedge App and click the MSR or RFID tab1.
Turn on the MSR or RFID module2.
Key in Prefix and Suffix codes to adjust the parse data format3.
Click Apply4.
NOTE: Unless you are sure you need to change the parse data format, we recommend
you do not use this seng.

DT307SQ
ENGLISH 2 3 ENGLISH
If your DT307SQ comes with a Barcode Scanner, RFID Reader and/or MSR module(s), you
may refer to the steps below to configure the sengs.
BASIC MODULE OPERATION
3 steps to capture the data results from Keyboard Wedge:
Turn on module from the1. Keyboard Wedge App
Launch a note-related App2.
Capture the data and verify the results3.
BARCODE SCANNER
Launch the scanner module, and adjust the parse data format :
Tap the1. Keyboard Wedge App , select SCAN tab, and turn on the Scanner module
Key in Prefix and Suffix codes to adjust the parse data format2.
Click3. Apply
NOTE: To ensure the system performance, turn on only the symbologies you are
going to use.
DT307SQ I/O Ports
DT307SQ LED Status Indicators
1. Power Mode Status Indicator:
2. Wi-Fi Status Indicator:
Blue: Device is powered on•
Blinking Blue: Main baery charging•
Orange: Low baery mode•
Blinking Orange: Extremely low baery mode•
Off: Device is powered offor in suspend mode•
Blue: Connected to a wireless AP•
Blinking blue: Connecng to a wireless AP•
Off: Wi-Fi is disabled•
A
B
C
D
E
F
Magnec stripe reader (Oponal)
Trigger buon
Camera (Oponal)
LED Flash (Oponal)
Power buon
Baery switch
G
H
I
J
K
L
Micro-SD card reader
Speaker
mini USB port
Headphone-out
USB 2.0 port
DC-in
DT307SQ Front View
DT307SQ Side View
DT307SQ Rear View
A
C D E
F G H
B
I
A
J
K
L
Data Capture Module Operaon Guide
Add/ remove barcode symbologies
Tap1. Barcode Scanner App
Turn on/offeach barcode symbologies under2. SYMBOLOGY tab