DT Research DT307SC Assembly instructions

DT307SC
ENGLISH
Mobile POS Tablet
BASIC OPERATION GUIDE
DT307SC
ENGLISH 4
signage dtri com
DT Research, Inc.
2000 Concourse Drive, San Jose, CA 95131
Copyright © 2016, DT Research, Inc. All Rights Reserved. BOGW091316 DT307SCENG
INTRODUCTION
Thank you for acquiring the DT307SC Mobile Tablet. The DT307SC offers a 7”capacive
touch display in a compact, rugged, and lightweight package. The DT307SC enables efficient
point-of-service/sales applicaons, inventory management, and field services.
The DT307SC provides the precise features needed to streamline operaons and improve
producvity, data accuracy, and service.
PACKAGE CONTENTS
One DT307SC•
One Baery Pack and Handstrap•
AC-DC Power Adapter•
Basic Operaon Guide•
*The actual package contents may vary depending on the configuraon acquired.
PRECAUTIONS
Always exercise care when operang and handling the DT307SC.•
Do not disassemble any poron of the DT307SC, as this will void any product warranty.•
Do not use any power adapter or charging cradle other than the one provided with the•
tablet or acquired from the manufacturer or its partners.
In the unlikely event that abnormal noise, strange odor, or smoke is present, immediately•
power down the DT307SC and disconnect all power sources. Please report the problem
to your device provider immediately.
MODIFY THE READING RESULT FOR SCANNER/ RFID/ MSR
Adjust the data capture module reading result:
Launch1. Keyboard Wedge menu from taskbar
Go to2. Configuraon
CAMERA UTILITY
Capture Picture/Video:
Launch the1. Camera Ulity from Start > Camera
Select the picture mode by pressing2. Screenshot or Video buon
For other advanced sengs, please select the3. sengs to modify from Browser/
Resoluon/Flashlight or other Properes for the file captured
ADVANCED SETTINGS - MSR
Enable/disable MSR module, and set up the Parse Data Format for MSR:
Launch1. Keyboard Wedge menu from taskbar
Go to2. Configure MSR
Select3. Enable to set up the configuraon
NOTE: Unless you are sure you need to enable parse, we recommend you do not
use this seng.

DT307SC
ENGLISH 2 3 ENGLISH
If your DT307SC comes with a data capture module(s), you may refer to the content
below to configure the sengs.
BASIC MODULE OPERATION
3 steps to capture the data results from Keyboard Wedge:
Connect module from1. Keyboard Wedge
Launch2. NotePad
Capture the data3.
Verify the result4.
ADVANCED SETTINGS - BARCODE SCANNER
Set up the symbologies, Scanner reading, or return the setup to factory mode:
Launch Scanner configuraon from1. Start> Sengs> System> Scanner Configure
Press2. Connect
NOTE: Please disconnect scanner from Keyboard Wedge first.
DT307SC I/O Ports
DT307SC LED Status Indicators
1. Power Mode Status Indicator:
2. Wi-Fi Status Indicator:
Blue: Device is powered on•
Blinking Blue: Main baery charging•
Orange: Low baery mode•
Blinking Orange: Extremely low baery mode•
Off: Device is powered offor in suspend mode•
Blue: Connected to a wireless AP•
Blinking blue: Connecng to a wireless AP•
Off: Wi-Fi is disabled•
AG
BH
CI
DJ
EK
L
F
Magnec stripe reader
Trigger buon
Camera (Oponal)
Flashlight (Oponal)
Power buon
Baery switch
Micro-SD card reader
Speaker
mini USB port
Headphone-out
USB 2.0 port
DC-in
DT307SC Front View
DT307SC Side View
DT307SC Rear View
A
I
A
J
K
L
C D E
F G H
B
Data Capture Module Operaon Guide