DTS NicKWash 600 User manual

Made in ItalyMade in Italy
D.T.S. Illuminazione srl
Via Fagnano Selve 10/12/14
47843 Misano Adriatico (RN) ITALIA Tel [phone] Fax [phone] [email protected] http://www.dts-lighting.it
GBGB
User’s Manual Rel 1.2User’s Manual Rel 1.2

Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia
non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo
documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso
scritto della D.T.S .
DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di
design a ciascun proprio prodotto. D.T.S non assume alcuna responsabilità sull’uso o sull’applicazione dei
prodotti o dei circuiti descritti.
The information contained in this publication has been carefully prepared and checked. However, no
responsibility will be taken for any errors. All rights are reserved and this document cannot be copied,
photocopied or reproduced, in part or completely, without prior written consent from D.T.S.
D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products
without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits
described herein.
Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand
soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits
réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement,
sans le consentement préalable de .
se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles ou
de design, sans préavis, à chacun de ses produits. décline toute responsabilité sur l'utilisation ou
sur l'application des produits ou des circuits décrits.
D.T.S
D.T.S.
D.T.S.
Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y
controladas. Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes.
Todos los derechos han sido reservados y este documento no puede ser copiado, fotocopiado
o reproducido, total o parcialmente, sin previa autorizaciónescrita de
se reserva el derecho a aportar sin previo aviso cambios y modificaciones de carácter
estético, funcional o de diseño a cada producto suyo. no se asume responsabilidad de
ningún tipo sobre la utilización o sobre la aplicació
n de los productos o de los circuitos descritos.
D.T.S.
D.T.S.
D.T.S.
ARC 1200
NICK WASH 600
2

ARC 1200
3NICK WASH 600
INDEX
1- SYMBOLS 4
2- GENERAL WARNING 4
3- GENERAL WARRANTY CONDITION 4
4- TECHNICAL FEATURES 5
5- TECHNICAL SPECIFICATIONS 5
6- ACCESSORIES 7
7- IMPORTANT SAFETY INFORMATION 8
7.1 Fire prevention
7.2 Prevention of electric shock
7.3 Safety
7.4 Level of protection against the penetration of solid and liquid objects
8- VOLTAGE AND FREQUENCY 9
9- INSTALLATION 9
9.1 Safety cable
9.2 Protection against liquids
9.3 Movement
9.4 Risk of fire
9.5 Forced ventilation
9.6 Ambient temperature
10- MAINS CONNECTION 10
10.1 Protection
11- DMX SIGNAL CONNECTION 11
11.1 DMX Addresses
11.2 Selecting the DMX address
12- FIRMWARE UPDATING 12
13- DISPLAY FUNCTIONS 13
14- PERIODIC CLEANING 22
15- PERIODIC CONTROLS 22
16- DMX PROTOCOL 23

ARC 1200
1- SYMBOLS
Graphic symbols used on this manual
2- GENERAL WARNING
Read the instruction contained in this user manual carefully, as they give important information
regarding safety during installation , use and maintenance.
The device is not for domestic use and must be installed by a qualified electrician or experienced
person.
Always disconnect the device from the mains before replacing the lamp.
The lamp must be replaced if it has been damaged or deformed by prolonged use or overheating.
The device must always be equipped with an efficient ground connection.
3- GENERAL WARRANTY CONDITIONS
The unit is guaranteed for 24 months from the date of purchase against manufacturing material defects.
THIS SYMBOL INDICATES A HOT SURFACE
THIS SYMBOL INDICATES ELECTRIC SHOCK RISK
THIS SYMBOL INDICATES GENERAL RISK
THIS SYMBOL MEANS “DO NOT PLACE THE UNIT ON
INFLAMMABLE SURFACES”
0,5M THIS SYMBOL INDICATES THE MINIMUM DISTANCE TO
BE KEPT BETWEEN THE DEVICE AND THE LIT OBJECT
4
F
!
NICK WASH 600

ARC 1200
5NICK WASH 600
4- TECHNICAL FEATURES
The FAR features also a Free Axis Rotation (“FAR”) system.
The FAR allows limitless pan and tilt rotation: the NICK head rotates freely on its axes, horizontally or
vertically, without interruption, in either direction, never having to reverse motion.
NICK WASH 600
03.LDR005.T
03.LDR005.TF
03.LDR005.TWS
5- TECHNICAL SPECIFICATIONS
Overview
NICK WASH 600 is a self-contained compact high-output LED moving head projector with 13,5° - 40°
motorized zoom.
NICK WASH 600 is one of the brightest compact LED projectors on the market: luminosity at 5 m is no
less than 3.100 Lux (13,5°).
Applications
NICK WASH 600 is ideal in various applications, such as: lighting shopping malls, libraries, museums,
exhibitions, clubs, restaurants, buildings, monuments, as well as special events, fashion displays, etc.
The unit is easily installable even in the most refined settings, thanks to its attractive appearance.
LED technology
NICK WASH 600 light source is composed of 120 LEDs (30 Red,30 Green, 30 Blue, 30 White) with 9.750
total lumens.
The LEDs even distribution pattern featuring the same quantity of red, green, blue and white LEDs
guarantees high colour mixing quality and a uniform projection on surfaces, no matter what colour
is used.
NICK WASH 600 offers 2 different colour mixing modes (RGBW / CMY) and can generate 16 million
colours; colour temperature can be varied over a linear range from 2800°K to 6500°K.
Also, users can memorize a personalized white either from the menu or via DMX. The white is recalled
with the dedicated DMX “White” channel.
NICK WASH 600 is also available with 90 White +30 Amber LEDs, or in an RGBA version (on request).
Zoom . Pan/Tilt . Full-range power supply
NICK WASH 600 features a motorized linear Zoom (13,5°- 40°) with a high efficiency optics system;
zoom movement is smooth and uniform.
NICK WASH 600 features a motorized movement on horizontal (540° pan) and vertical (270° tilt) axes;
the unit can operate in vertical, horizontal or inverted positions, and can be positioned on the floor or
ground, or fitted to trusses; it is complete with a practical accessory for anchorage to the ground.
NICK WASH 600
NICK WASH 600 has a full-range AC 90-260 V, 50-60 Hz power supply, therefore ensures reliable
operation even in the case ofvoltage drops. Also, the unit can be used all over the world with no
specific adaptations, as the right voltage is always supplied.
Electr. Power Supply, Motorized Zoom, Black colour
Electr. Power Supply, Motorized Zoom, F.A.R. system, Black colour
Electr. Power Supply, Motorized Zoom, Wireless DMX ready, Black colour
LED technology
120 LEDs (30 Red, 30 Green, 30 Blue, 30 White); total luminous flux 9.750 Lumens
RGBW colour generation (16 million colours); 3 different colour mixing modes: RGBW, CMY, HSV
Colour temperature variable on a linear range (2.800°K÷6.500°K); no infrared / no ultraviolet emissions
LEDs average lifespan: 100.000 hours
Zoom
Motorized Zoom 13,5°- 40°
User interface
OLED colour display + 4 buttons

5- TECHNICAL SPECIFICATIONS
Free Axis Rotation (“FAR”) system;
Independent operation
Fully programmable via built-in user interface
Master or Slave capability (chains of up to 32 interconnected units)
Remote control
Remotely controlled by cable or wireless;
USITT DMX 512 serial digital protocol (reception / transmission)
DMX
17-20 DMX channels
Protection
IP20 protection rate
Movements (horizontal/pan – vertical/tilt axes)
Motorized movement 540° Pan (2.0 sec) / 270° Tilt (1.2 sec)
Power supply / consumption
Full range AC 90-260V, 50-60Hz
Power consumption:
* 90 V – 2,65 A – 240 W * 120 V – 2 A – 240 W * 230 V – 1 A – 240 W * 260 V – 0,9 A – 240 W
Thermal
Operating ambient temperature - 10° / + 40°
Finishes
Black or white finish
Certification and Safety
Certification CE;
LED Class
Class 2 LED product
Weight
7,9 Kg
ARC 1200
6
Dimensions
NICK WASH 600
Unit Dimensions (LxWxH)
360x217x440mm
Weight:
7,9 Kg
Packaging Dimensions (LxWxH)
430
Weight:
x 515 x 290 mm
10 Kg

6- ACCESSORIES
As standard
03.LDR005.T
03.LDR005.TF
•1 x POWERCONN male cable connector (cod. 0520P014)
•1 x XLR 5 Pins male cable connector (cod. 0508B028)
•1 x XLR 5 Pins female cable connector (cod. 0508B027)
•1 x “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (max. load. 80Kg) (cod. 0521A014)
• User’s manual
03.LDR005.TWS
• 1 x INDOOR IP20 omnidirectional 2dBi antenna cod. 0508A033
•1 x POWERCONN male cable connector (cod. 0520P014)
•1 x XLR 5 Pins male cable connector (cod. 0508B028)
•1 x XLR 5 Pins female cable connector (cod. 0508B027)
•1 x “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (max. load. 80Kg) (cod. 0521A014)
• User’s manual
Optional (on request)
03.LDR005.T)
Electr. Power Supply, Motorized Zoom, Black colour
Electr. Power Supply, Motorized Zoom, F.A.R. system, Black colour
Nick Wash 600 Electr. Power Supply, Motorized Zoom, Wireless
DMX ready, Black colour
Flight cases
• Professional Flight case for 4 units; compartment for accessories, swivel wheels, cover with hinges
with-stay, dishes on cover for piling, 8 handles (2 eachside) (cod. 0521C046.1)
Wireless DMX receivers retrofits (for
• Wireless DMX Receiver Card with INDOOR IP20 omni. 2dBi antenna included (cod.03.LA.117)
Clamps / safety wires
• “C” Clamp G60 black (max. load 50Kg) (cod. 0521A004)
• “C” Clamp G60 chrome (max. load. 50Kg) (cod. 0521A004.20)
• “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (max. load. 80Kg) (cod. 0521A014)
• “C” Clamp G100 black / professional (max. load. 200Kg) (cod. 0521A015)
• Omega clamp with “Fast Lock” connection 1⁄4 turn 1 couple (2 pieces) (Cod. 02K00467)
• Safety wire (3mm x 60 cm), ring spring catch, max. capacity load 60Kg (cod. 0521A010)
ARC 1200
7NICK WASH 600

7- IMPORTANT SAFETY INFORMATION
7.1 Fire prevention:
-Never locate the fixture on any flammable surface.
-Minimum distance from flammable materials: 1 MT.
-Minimum distance from the closest illuminable surface: 0,5 MT.
-Replace any blown or damaged fuses only with those of identical value. Refer to the wiring diagram if
there is any doubt.
-Connect the projector to mains power via a thermal magnetic circuit breaker.
7.2 Prevention of electric shock:
-High voltage is present inside the unit. Unplug the unit prior to performing any function which involves
touching the inside of the moving head.
-The level of technology inherent in the NICK WASH 600 requires the assistance of specialised personnel
for all servicing. Please refer to an authorised DTS service centre.
-A good earth connection is essential for proper functioning of the projector.
-Never connect the unit without proper earth connection.
-The fixture should be located in places with a good air ventilation.
7.3 Safety:
-The projector should always be installed with bolts, clamps and other tools that are capable of
supporting the weight of the unit.
-Always use a second safety cable to sustain the weight of the unit in case of the failure of the main
fixing point.
-The external surface of the unit, at various points, may exceed 70°C.
Never handle the unit until at least 10 minutes have elapsed since the
projector was turned off.
-Never install the fixture in an enclosed area lacking sufficient air flow. The ambient temperature should
not exceed 40°C.
7.4 Level of protection against the penetration of solid and liquid objects:
-The projector is classified as an ordinary appliance and its protection level against the penetration of
solid and liquid objects is IP 20.
ARC 1200
0,5M
8
F
!
!
NICK WASH 600

8- VOLTAGE AND FREQUENCY
The NICK WASH 600 can operate at 90-260 VOLT 50 or 60 Hz.
9- INSTALLATION
NICK WASH 600 may be either floor or ceiling mounted.
For floor mounting installations, the NICK WASH 600 is supplied with four rubber mounting feet on the
base.
For ceiling mounted installations, we reccomend the use of appropriate clamps to fix the unit to the
mounting surface.
The supporting structure from which the unit is hung should be capable of bearing the weight of the
unit, as should any clamps used to hung it. The structure should also be sufficiently rigid so as not to
move or shake whilst the NICK WASH 600 is moving.
Two 1/4 turn Fast Locks connections placed in the base of the units allow to hang the NICK WASH 600
by using the Fast Lock ‘C’ clamps provided in the box.
.
9.1- Safety cable
We recommend the use of a safety chain/cord connected to the NICK WASH 600 and to the suspension
truss in order to avoid the fixture accidentally falling should the main fixing point fail. Make sure that the
iron cable or chain can bear the weight of the entire unit.
You may attach the safety chain/cord to the attachment point (A) located on the base of the fixture, as
shown in the picture below.
9.2- Protection against liquids
The projector contains electric and electronic components which should under no circumstances come
into contact with oil, water or any other liquid. The proper unit functioning would be compromised
should this occur.
ARC 1200
9
!
NICK WASH 600
!
A
SAFETY CHAIN/CORD
ATTACHMENT POINT

9.3- Movement
Unlimited Pan rotation; unlimited Tilt rotation (NICK WASH 600 ZOOM F.A.R.)
Pan 540° (2,0 sec.), Tilt 270° (1,2 sec.) (NICK WASH 600 ZOOM)
9.4- Risk of fire
Each fixture produces heat and must be installed in a well-ventilated place. The minimum recommended
distance from flammable material is 1 MT.
Minimum distance from the object being illuminated is 0,5 MT.
9.5- Forced ventilation
You will note, on inspection, that the unit features various air inlets and cooling fans located on the head
of the fixture. These should, under no circumstances, be blocked or obstructed whilst the projector is in
operation.
Doing so could cause the fixture to seriously overheat thereby compromising its proper operation.
9.6- Ambient temperature
The projector should never be installed in places that lack a constant air flow. The ambient temperature
should NOT exceed 40°C.
10- MAINS CONNECTION
NICK WASH 600 operate at 90-260 VOLT 50-60 Hz.
Prior to connecting the unit to your mains supply,
ensure that the model in your possession correctly matches
the mains supply available. For connection purposes,
ensure that your plug is capable of supporting 1,5 amps at 230V,
Or 3 amps at 90 V
Strict adherence to regulatory norms is strongly recommended.
10.1- Protection
The use of a thermal magnetic circuit breaker is recommended for each
NICK WASH 600.
ARC 1200
10
0,5M
F
!
Mains
90-260V AC 50 / 60Hz
NICK WASH 600
Mains
90-260V AC 50 / 60Hz
03.LDR005.T
03.LDR005.TWS
!
WARNING
Do not place any object in the path
of the projector’s movement 540°
270°
Free Axis Rotation ("F.A.R.”)
No Free Axis Rotation ("F.A.R.”)
03.LDR005.TF