DTS XR1200 WASH Fresnel User manual

XR1200 WASH XR1200 WASH
GB
User Manual Rel 2.0

Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia
non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo
documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso
scritto della D.T.S.
DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di
design a ciascun proprio prodotto. D.T.S. non assume alcuna responsabilità sull’uso o sull’applicazione dei
prodotti o dei circuiti descritti.
The information contained in this publication has been carefully prepared and checked. However, no
responsibility will be taken for any errors. All rights are reserved and this document cannot be copied,
photocopied or reproduced, in part or completely, without prior written consent from D.T.S.
D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products
without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits
described herein.
Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand
soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits
réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement,
sans le consentement préalable de D.T.S.
D.T.S. se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles ou
de design, sans préavis, à chacun de ses produits. D.T.S. décline toute responsabilité sur l'utilisation ou
sur l'application des produits ou des circuits décrits.
Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y
controladas. Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes.
Todos los derechos han sido reservados y este documento no puede ser copiado, fotocopiado
o reproducido, total o parcialmente, sin previa autorizaciónescrita de D.T.S.
D.T.S. se reserva el derecho a aportar sin previo aviso cambios y modificaciones de carácter
estético, funcional o de diseño a cada producto suyo. D.T.S. no se asume responsabilidad de
ningún tipo sobre la utilización o sobre la aplicació
n de los productos o de los circuitos descritos.
ARC 1200
2XR1200 WASH

ARC 1200
3
INDEX:
1- TECHNICAL FEATURES 4
2- IMPORTANT SAFETY INFORMATION 6
2.1 Fire prevention
2.2 Prevention of electric shock
2.3 Protection against ultraviolet radiation
2.4 Safety
2.5 Level of protection against the penetration of solid and liquid matter
3- MOUNTING THE LAMP 7
3.1 Lamp alignment
4- VOLTAGE AND FREQUENCY 8
5- INSTALLATION 8
5.1 Safety cable
5.2 Protection against liquids
5.3 Movement
5.4 Risk of fire
5.5 Forced ventilation
5.6 Ambient temperature
6- MAINS CONNECTION 9
6.1 Protection
7- DMX SIGNAL CONNECTION 9
7.1 DMX Addresses
7.2 Selecting the DMX address
8- DISPLAY FUNCTIONS 12
9- 12
10- HIDDEN MENU 16
11- OPENING THE PROJECTOR HOUSING 17
12- PERIODIC CLEANING
12.1 Lenses and reflectors
12.2 Fans and air passages
13- PERIODIC CONTROLS
14- DMX PROTOCOLS 18
15-COLOUR WHEEL 23
16- 8 MOTORS CONTROL CARD 24
17- PAN & TILT CARD 25
18-CABLES RESEND CARD
19-DISPLAY CARD
20- LAMP ON-OFF CONTROL CARD
ERROR MESSAGES
XR1200 WASH

ARC 1200
4XR1200 WASH
1- TECHNICAL FEATURES
The XR1200 WASH is a brand new moving head fitted with a 1200W discharge lamp, which delivers a
massive 27.000 Lux at 5 m. The XR1200 WASH is fitted with a Philips MSR Gold 1200 Fastfit lamp
(95.000 Lumens) combined with a dichroic parabolic reflector. The XR1200 WASH incorporates motorized
zoom: 20°- 45°, rotating indexable beam shaper (0°-180°), 2 frost filters, 2 colour conversion filters
(3.200°K and 5.600°K), CMY colour generation + a colour wheel (6 dichroic filters + open, with linear
selection for perfect 2-colour beams), and electromagnetic or electronic ballast. The XR1200 WASH also
includes a new Pan / Tilt locking system with recessed buttons. The XR1200 WASH is particularly
suitable for all professional applications, both mobile (concerts, shows, tours, special events) and fixed
(clubs and other venues), requiring a light with extremely luminous output capable of illuminating
objects and large backgrounds with an endless variety of colours.
• Electronic ballast 90-260V 50/60 Hz• Black colour
All models are also available in white colour
Lamp
Lamp: Philips MSR Gold 1200 Fastfit . Automatic switching on of lamp in case of accidental switching off
Lamp on/off via DMX; reset via DMX.
Optical group
27.000 Lux at 5 m (20°). Fresnel lens Ø 200 mm. Borosilicate dichroic parabolic reflector
Zoom
Motorized zoom (20°- 45°)
Dimmer / shutter / strobo
Linear dimmer, Shutter, Strobe from 0,85 flash/sec to 10 flash/sec
Power saving mode (the lamp dims to 50% six seconds after shutter closure)
Colours
CMY color generation system with 3 palettes + colour wheel (6 colours + open) with linear selection for
perfect 2-colour beams. Color change with blackout sync
Effects
Rotating and indexable beam shaper (0°-180°)
Pan / Tilt
Pan 540° (3,9 sec.). Tilt 320° (2,6 sec.). 16-bit resolution
3-Speed function (3 selectable pan/tilt speeds); extremely smooth and precise movements even at the
highest speeds. Pan / Tilt locking system with recessed buttons. Automatic Pan/Tilt repositioning in case
of knocks
16 DMX channels
Internal operating system updatable via DMX
Connections
4 XLR connectors (3-pole In and Out; 5-pole In and Out) by Neutrik
Power supply
Electronic ballast: 90 - 260 V (50/60 Hz); power consumption: 820 W
Standard accessories
2 x “C” GQuick clamps with “fastlock” connection 1/4 turn
Thermal
Operating ambient temperature: -10° / 40°
XR 1200 WASH (Cod. 03.MW005.EB.L)
Weight
38 Kg (electronic ballast)

490 mm 460 mm
6 0 mm
4
685 mm
430 mm 500 mm
270°
1- TECHNICAL FEATURES
ACCESSORIES
• MSR Gold 1200 Fastfit lamp (cod. 0505S019)
• Double Professional Flight case; compartment for lamps and accessories, swivel wheels, cover with
hinges with-stay, dishes on cover for piling, 8 handles (2 each side)
• Embedding flange for XR (visible display) (cod. 03.MA005)
• Embedding flange for XR (no visible display) (cod. 03.MA006)
• Wireless DMX receiver card (cod. 03.LA.012)
• “C” Clamp G60 black (max. load 50Kg) (cod. 0521A004)
• “C” Clamp G60 chrome (max. load. 50Kg) (cod. 0521A004.20)
• “C” Clamp GQUICK with “Fast Lock” connection 1/4 turn (max. load. 80Kg) (cod.0521A014)
• “C” Clamp G100 black / professional (max. load. 200Kg) (cod. 0521A015)
• Omega clamp with “Fast Lock” connection 1⁄4 turn
• Safety wire (3mm x 60 cm), ring spring catch, max. capacity load 60Kg (cod. 0521A010)
Packaging Dimensions (AxLxP)
580 x 490 x 800mm
Weight
50 Kg (with electronic ballast).
ARC 1200
5XR1200 WASH

6
2- IMPORTANT SAFETY INFORMATION
2.1 Fire prevention:
The use of any other alternative lamp is not recommended and will null and void the fixture's warranty.
-Never locate the fixture on any flammable surface.
-Minimum distance from flammable materials: 1 MT.
-Minimum distance from the closest illuminable surface: 2 MT.
-Replace any blown or damaged fuses only with fuses of identical value. Refer to the wiring diagram if
there is any doubt.
-Connect the projector to mains power via a thermal magnetic circuit breaker.
2.2 Prevention of electric shock:
-High voltage is present inside the unit. Unplug the unit prior to performing any function which involves
touching the inside of the moving head, including lamp replacement.
-The level of technology present in the XR1200 requires the assistance of specialised personnel for all
servicing. Please refer to an authorised DTS service centre.
-A good earth connection is essential for proper functioning of the projector.
-Never connect the unit without proper earth connection.
-The fixture should be located in places with a good air ventilation.
2.3 Protection against ultraviolet radiation:
-Never turn on the lamp if any of the lenses, filters or ABS covering is damaged. Their respective
shielding functions will only operate efficiently if they are in perfect working order.
-Never look directly the lamp when it is on.
2.4 Safety:
-The projector should always be installed with bolts, clamps and other tools that are capable of
supporting the weight of the unit.
-Always use a second safety cable to sustain the weight of the unit in case of the failure of the main
fixing point.
-The external surface of the unit, at various points, may exceed 70°C. Never handle the unit until at
least 10 minutes have elapsed since the lamp was turned off.
-Always replace the lamp if any physical damage is evident.
-Never install the fixture in an enclosed area lacking sufficient air flow. The ambient temperature should
not exceed 40°C.
-A hot lamp may explode, so always wait for at least 10 minutes prior to attempting to replace the lamp.
-Always wear suitable hand protection when handling the lamp.
2.5 Level of protection against the penetration of solid and liquid matter:
-The projector is classified as an ordinary appliance and its protection level against the penetration of
solid and liquid matter is IP 20.
XR1200 WASH uses a Philips MSR Gold 1200 Fastfit lamp.
XR1200 WASH

3- MOUNTING THE LAMPS
Warning: Switch off the unit before replacing the lamp.
1) Using a screwdriver, loose the 3 screws A, B, C, (photo 1) and remove the metal cover .
2) Insert the lamp (photo2).
3)Rotate the lamp 1/4 turn clockwise (photo 3 and 4).
The lamp used on XR1200 is made in quartz glass and should be handled with care. Always follow the
instructions supplied in the lamp's packaging. Never touch the glass directly but use the tissue provided
in the lamp's packaging. The lamp socket is not symmetrical.
DO NOT USE UNDUE FORCE ON THE GLASS. In case of difficulty, read again the instructions and repeat
the procedure.
4) Replace the metal cover and tighten the screws A,B,C, which where previously removed.
3.1 Lamp alignment
Attention: we recommend to align the lamp in the optical system to avoid overheating of the dichroic
filters and other components inside the unit.
Alignment is carried out using the 3 adjusters X, Y and Z.
During this operation you must have a uniform luminosity all around the projected area.
Philips MSR Gold 1200 Fastfit
Power 1200W
Luminous flux 95,000 lm
Colour temperature 6.300°K
Lampbase PGJX50
Rated life 750 hours
PGJX50
7
Photo 2Photo 1 Photo 4Photo 3
Photo 5
XR1200 WASH

4- VOLTAGE AND FREQUENCY
The XR1200 with electronic ballast can operate at 90-260 VOLT 50 or 60 Hz.
5- INSTALLATION
XR1200 may be either floor or ceiling mounted.
For floor mounting installations, the XR1200 is supplied with four rubber mounting feet on the base.
For ceiling mounted installations, we reccomend the use of appropriate clamps to fix the unit to the
mounting surface.
The supporting structure from which the unit is hung should be capable of bearing the weight of the
unit, as should any clamps used to hung it. The structure should also be sufficiently rigid so as not to
move or shake whilst the XR1200 is moving.
Eight quarter turn fast locks placed on the base of the units,allows by using the two fast lock C clamps
provided in the box, to fix the unit in any position.
.
5.1- Safety cable
We recommend the use of a safety cable or chain connected to the XR1200 and to the suspension truss
in order to avoid the fixture accidentally falling should the main fixing point fail. Make sure that the iron
cable or chain can bear the weight of the entire unit.
You may attach the safety chain to the two holes (A) located on the base of the fixture, as shown in the
picture below.
5.2- Protection against liquids
The projector contains electric and electronic components which should under no circumstances come
into contact with oil, water or any other liquid. The proper unit functioning would be compromised
should this occur.
8XR1200 WASH
A

5.3- Movement
The projector has a maximum movement of 540° for Pan and 270° for Tilt. DO NOT place any
obstructions in the path of the projector's movement.
5.4- Risk of fire
Each fixture produces heat and must be installed in a well-ventilated place. The minimum recommended
distance from flammable material is 1 MT.
Minimum distance from the object being illuminated is 2 MT.
5.5- Forced ventilation
You will note, on inspection, that the unit features various air inlets and cooling fans located on both the
base and head of the fixture. These should, under no circumstances, be blocked or obstructed whilst the
projector is in operation.
Doing so could cause the fixture to seriously overheat thereby compromising its proper operation.
5.6- Ambient temperature
The projector should never be installed in places that lack a constant air flow. The ambient temperature
should NOT exceed 40°C.
6- MAINS CONNECTION
XR1200 with electronic ballast operate at 90-260 VOLT 50-60 Hz.
Prior to connecting the unit to your mains supply,
ensure that the model in your possession correctly matches
the mains supply available. For connection purposes,
ensure that your plug is capable of supporting 8 amps at 230V,
Or 16 amps at 100-120 V
Strict adherence to regulatory norms is strongly recommended.
6.1- Protection
The use of a thermal magnetic circuit breaker is recommended for each XR1200.
A good earth connection is essential for the correct operation of the projector.
7- DMX SIGNAL CONNECTION
The unit operates using the digital DMX 512 (1990) signal. Connection between the mixer and the
projector or between projectors must be carried out using a two pair screened ø 0.5 mm cable and a
CANNON XLR 5 or 3 pins connector.
9
Electronic ballast
90-260V 50 / 60Hz
XR1200 WASH
540°
270°

Ensure that the conductors do not touch each other. Do not connect the cable ground to the XLR chassy
The plug housing must be isolated. Connect the mixer signal to the DMX IN projector plug and connect it
to the next projector by connecting the DMX OUT plug on the first projector to the DMX IN plug of the
second one.
In this way, all the projectors are cascade connected.
NB. If the display showing the DMX address flashes, then one of the following errors has occurred:
- DMX signal not present
- DMX address not valid
- DMX reception problem
For Installations where long distance DMX cable connections are needed,we suggest to use a DMX
terminator.
The DMX terminator is a male XLR 3-5 pins connector with a 120 ohm resistor
Between pin 2 and 3.
The DMX terminator must be plugged into the last unit (DMX out panel connector) of the DMX line.
5
3
4 2
11=GND
2=DATA-
3=DATA+
CONTROLLER
S T A N D A R D
D M X 5 1 2
1
2
3
5
4
OUT
120 ohm
PIN 3
PIN 2
PLACE A 120 OHM RESISTOR BETWEEN PIN 2
AND 3 OF A MALE XRL CONNECTOR AND PLUG IT
INTO THE DMX OUT PANEL CONNECTOR OF THE
LAST UNIT CONNECTED TO THE DMX LINE
10 XR1200 WASH

7.1-DMX Addresses
XR1200 WASH have 16 DMX channels.
Set the following addresses on the mixer:
Projector 1 A001
Projector 2 A017 If you want to select the next projector, just add “16”
Projector 3 A033
….. A….
projector 6 A081
7.2-Selecting the DMX address
1) Press the UP-DOWN key until you reach the required DMX channel. The numbers on the display will
start to flash (but the new DMX address hasn't yet been set).
2) Press ENTER to confirm your selection. The numbers on the display will stop flashing and the
projector is now setted to the new DMX address.
TRICKS:
if you keep pushed the UP or DOWN keys, the channels are calculated more quickly and you get a
faster selection.
11 XR1200 WASH

MAINS
Electronic ballast
90-260V 50 / 60Hz
DMX IN
DMX OUT
DISPLAY
MENU
ENTER DOWN
UP
8- DISPLAY FUNCTIONS
12
DISPLAY FUNCTIONS
The XR1200 display panel shows all the available functions . Using these functions, it is possible to
change some of the parameters and add some functions. Changing the DTS setting can vary the
functions of the unit so that it does not respond to the DMX 512 used to control it. Carefully
follow the instructions below before carrying out any variations or selections.
NOTE: the symbol shows which key has to be pushed to obtain the desired function.
XR1200 WASH
DMX IN
DMX OUT
FUSE 16A T 5X20
PAN DIRECTION
NORMAL
MENU ENTER DOWN UP
Pan Direction
Up-Down Up-DownENTER
PAN DIRECTION
This menu allow to set the Pan
movement.
Normal or Reversed
Pan movement Normal or Reversed
Default = Normal ENTER
Menu
TILT DIRECTION
NORMAL
MENU ENTER DOWN UP
Tilt Direction
Up-Down Up-DownENTER
TILT DIRECTION
This menu allow to set the Pan
movement.
Normal or Reversed
Tilt movement Normal or Reversed
Default = Normal ENTER
Menu
PAN TILT SPEED
2
MENU ENTER DOWN UP
Pan Tilt Speed
Up-Down Up-DownENTER
PAN TILT SPEED
Pan Tilt Speed control (1-3)
Pan Tilt Speed control
Default = 2 ENTER
Menu

13 XR1200 WASH
SILENT PAN TILT
ON
MENU ENTER DOWN UP
Silent Pan Tilt
Up-Down Up-DownENTER ON = Silent Mode enabled (Default)
OFF = Silent Mode disabled ENTER
Menu
8- DISPLAY FUNCTIONS
SILENT PAN TILT
Silent operating mode during PAN&TILT movement.
By activating this function, PAN and TILT motors will
be driven with less power (during aceleration and
deceleration) in order to reduce the noise during
PAN&TILT rotation
MENU ENTER DOWN UP
Display
Up-Down Up-DownENTER Display Flip
ON THE GROUND (Default)
SUSPENDED
ENTER
Menu
DISPLAY FLIP / STAND BY / CONTRAST
Display Flip:
Reverses display's reading depending on the
mounting position
(On the ground or suspended).
Display Standby:
To turn off the display (after 5 seconds)
Or leave it always on.
Display Contrast:
Display contrast regulation (1-16)
FLIP
ON
FLIP
ON THE GROUND
DISPLAY
MENU ENTER DOWN UP
FLIP
STANDBY
OFF
DISPLAY
MENU ENTER DOWN UP
FLIP
CONTRAST
8
DISPLAY
Display Standby
OFF = Display Standby disabled
(Default)
ON = Display goes OFF after 5
seconds
ENTER
Display Contrast
1-16 (Default = 8)
DMX MODE
MODE 1
MENU ENTER DOWN UP
DMX Mode
Up-Down Up-DownENTER Mode1 = 16 DMX channels, Pan&Tilt
16 bit (Default)
Mode2 = Same fixture as XR7 WASH
16 DMX channels, Pan&Tilt 16 bit
ENTER
Menu
DMX MODE
To select DMX mode :
Mode 1 or Mode 2
ENTER
TEST MODE
Full test and single function test.
MOTORS TEST
ALL
MENU ENTER DOWN UP
Motors Test
Up-Down Up-DownENTER Motors Test
ALL ,PAN, TILT, DIMMER, SHUTTER,
COLOUR WHEEL, CYAN, MAGENTA,
YELLOW,
EFFECTS, ZOOM
ENTER
Menu

Lamp
Up-Down Up-DownENTER BY DMX = ON / OFF via DMX (default)
ALWAYS ON = Forced ON
ALWAYS OFF = Forced OFF
RESET COUNTER = Lamp life time
reset
ENTER
Menu
14 XR1200 WASH
8- DISPLAY FUNCTIONS
LAMP
Lamp always ON, always OFF,
lamp ON-OFF selectable via DMX
And lamp life time reset
ADJUST
To adjust the lamp with no mixer
connected.
It’s possible to set the parameters for
PAN-TILT and ZOOM
MENU ENTER DOWN UP
FLIP
BY DMX
LAMP
MENU ENTER DOWN UP
FLIP
ADJUST
LAMP LAMP ADJUST =
To adjust the lamp
with no mixer connected.
It’s possible to set the parameters for
PAN-TILT and ZOOM
ENTER
RESET
ENABLED
MENU ENTER DOWN UP
Reset
Up-Down Up-DownENTER ENABLED = Reset via DMX enabled
(Default)
DISABLED = Reset via DMX disabled
NOW = Unit motors reset
ENTER
Menu
RESET
Reset via DMX ENABLED / DISABLED
and unit reset
BY DMX
CMY BLACKOUT
ON
MENU ENTER DOWN UP
CMY Blackout
Up-Down Up-DownENTER ON = Blackout enabled (Default)
OFF = Blackout disabled ENTER
Menu
CMY BLACKOUT
CMY filters blades inserted at 100% if the dimmer
remain closed for more than 5 seconds.
By activating this function, it will be possible to
reduce substantially any visible light reflection
coming out from the front lens when dimmer is
closed.
SYSTEM INFO
LAMP LIFE:0000H STRIKE:001
UNIT LIFE: 0010H
8M R.15
PT R.10
MODEL: XR1200 WASH
MENU ENTER DOWN UP
System info
Up-Down Up-DownENTER SYSTEM INFO
Lamp life time, lamp strikes, unit life
time, 8 motors card software
version, Pan&Tilt card software
version and unit model
ENTER
Menu
SYSTEM INFO
Lamp life time, lamp strikes, unit life time, 8
motors card software version, Pan&Tilt card
software version and unit model
Reserved
Up-Down Up-DownENTER Pan Lock = Lock the Pan to the
desired value
Tilt Lock = Lock the Tilt to the
desired value
Pan Free = Remove power to Pan
motor
Tilt Free = Remove power to Tilt
motor
System Reboot = Unit Reboot
without needing of turning OFF the
unit
ENTER
Menu
RESERVED
Pan lock-Tilt lock
Pan free-Tilt free
System Reboot
(Code = 100)
RESERVED
000
MENU ENTER DOWN UP
ENTER CODE
PAN LOCK
NO
MENU ENTER DOWN UP

Default
Up-Down Up-DownENTER Default
To restore main settings ENTER
Menu
DEFAULT
To restore main settings
DEFAULT
SURE?
MENU ENTER DOWN UP
RESTORE MAIN SETTINGS
DEFAULT
RESTORE MAIN SETTINGS
MENU ENTER DOWN UP
15 XR1200 WASH
PRESS ENTER TO CONFORM
PRESS MENU TO CANCEL
9- ERROR MESSAGES
8- DISPLAY FUNCTIONS
MENU ENTER DOWN UP
ERROR
COLOUR WHEEL
MENU ENTER DOWN UP
ERROR
EFFECTS
MENU ENTER DOWN UP
ERROR
ZOOM LEFT
MENU ENTER DOWN UP
ERROR
ZOOM RIGHT
MENU ENTER DOWN UP
ERROR
PAN
MENU ENTER DOWN UP
ERROR
TILT
MENU ENTER DOWN UP
ERROR
INTERNAL BUS
MENU ENTER DOWN UP
ERROR
DMX ADDRESS
COLOUR WHEEL
POSITION ERROR
BEAM SHAPE WHEEL
POSITION ERROR
LEFT ZOOM SENSOR
POSITION ERROR
RIGHT ZOOM SENSOR
POSITION ERROR
PAN REPOSITIONING
ENCODER ERROR
TILT REPOSITIONING
ENCODER ERROR
COMMUNICATION
PROBLEM BETWEEN 8
MOTORS CARD AND
PAN&TILT CARD
DMX ADDRESS
ERROR

10- HIDDEN MENU
For technical personnel only.
To operate this menu:
-Connect the projector to the DMX controller (DMX SIGNAL MUST BE CORRECTLY RECEIVED)
- Reset the XR1200 (reset from the MENU, not from the DMX controller!).
- While reset is running, press the MENU and ENTER keys at the same time.
16 XR1200 WASH
PAN ALIGNMENT
To align pan position
TILT ALIGNMENT
To align tilt position
SHUTTER ALIGNMENT
To align shutter blades
EFFECTS ALIGNMENT
To Align Effects wheel
ZOOM RIGHT ALIGNMENT
To align zoom right position
COLOUR WHEEL ALIGNMENT
To align colour wheel
CYAN ALIGNMENT
To align cyan colour
MAGENTA ALIGNMENT
To align magenta colour YELLOW ALIGNMENT
To align yellow colour
ZOOM LEFT ALIGNMENT
To align zoom left position
ELECTRONIC
CALIBRATION OF THE
MOTORS
RESET EEPROM.
RESET ALL SETTINGS
TO 128 VALUE
EXIT FROM HIDDEN
MENU
CALIBRATION
PAN
MENU ENTER DOWN UP
MOTORS ALIGNMENT
134
DEFAULT CAL
MENU ENTER DOWN UP
SET ALL MOTORS AT 128
EXIT TO MAIN
MENU ENTER DOWN UP
Calibration mode
CALIBRATION
PAN
MENU ENTER DOWN UP
MOTORS ALIGNMENT
134
CALIBRATION
TILT
MENU ENTER DOWN UP
MOTORS ALIGNMENT
167
CALIBRATION
SHUTTER
MENU ENTER DOWN UP
MOTORS ALIGNMENT
145
CALIBRATION
COLOUR WHEEL
MENU ENTER DOWN UP
MOTORS ALIGNMENT
151
CALIBRATION
EFFECTS
MENU ENTER DOWN UP
MOTORS ALIGNMENT
149
CALIBRATION
ZOOM RIGHT
MENU ENTER DOWN UP
MOTORS ALIGNMENT
97
CALIBRATION
ZOOM LEFT
MENU ENTER DOWN UP
MOTORS ALIGNMENT
85
CALIBRATION
CYAN
MENU ENTER DOWN UP
MOTORS ALIGNMENT
162
CALIBRATION
MAGENTA
MENU ENTER DOWN UP
MOTORS ALIGNMENT
121
CALIBRATION
YELLOW
MENU ENTER DOWN UP
MOTORS ALIGNMENT
106

17
11- OPENING THE PROJECTOR HOUSING
It is possible to inspect the inside of the projector by removing the cover as indicated below.
ATTENTION
REMOVE MAINS POWER PRIOR TO ACCESSING THE PROJECTOR’S INTERNAL COMPONENTS.
1) Loosen the 3 (1/4 turn) screws which fix the head covers (photo 1) .
2) Once unscrewed, simply lift the covers to access the internal components (photo 2).
Photo 1
XR1200 WASH
Photo 2
12- PERIODIC CLEANING
12.1- Lenses and reflectors
Even a fine layer of dust can substantially reduce the luminous output . Regularly clean all lenses
and the reflector using a soft cotton cloth, dampened with a specialist lens cleaning solution.
12.2- Fans and air passages
The fans and air passages must be cleaned approximately every 6 weeks. This periodic cleaning
will depend of course, on the conditions in which the projector is operating. Suitable instruments
for performing this type of maintenance are a brush and a common vacuum cleaner or an air
compressor. If necessary, clean the fans and air passages more frequently.
13- PERIODIC CONTROLS
Lamp
The lamp should be replaced if there is any visible damage or deformation due to heat. This will
help to avoid the danger of the lamp exploding.
Mechanical parts
Periodically check all mechanical parts, gears, guides, belts, etc. for wear and tear, replacing them
if necessary. Periodically check the lubrication of all components, particularly the parts subject to
high temperatures. If necessary, lubricate with suitable lubricant, available from your D.T.S.
distributor. Check the tension of the belts and adjust it if necessary.
Electrical components
Check all electrical components for correct earthing and proper connection of all connectors;
refasten them if necessary.
Fuse replacement
Locate the fuse, which protects the lamp and electronics, in the base of the XR1200.
Using a multimeter, test the condition of the fuse, replacing it with one of equivalent type if
necessary.

14- DMX PROTOCOL
18
16 CHANNEL MODE ( 16bit)
1 PAN ms b ( 5 4 0°)
2
3 TILT msb(320°)
4 TILT l s b
5
6 D IM MER
7 SHU T T ER
8 C OL OUR
9 C YAN
10 MAGENTA
11 YEL L O W
12 SPEED CMY / DIMMER
13 MACRO CMY / COLOUR
14 E FF ECTS
15 ZOOM
16 RESET
DMX CHANNEL 1 Parameter: PAN msb 540°
DMX CHANNEL 2 Parameter: PAN lsb
DMX CHANNEL 3 Parameter: TILT msb 319°
DMX CHANNEL 4 Parameter: TILT lsb
DMX CHANNEL 5 Parameter: MOVEMENT SPEED
DMX range
Value Mid point DMX value
Move
range
(degrees)
Mode Option Function
0-10 Standard
11-25 Fast movement
26-127 Vector mode from fast to slow
128-247 Variable time reaction to
DMX signal ( fast to slow)
248-255 Slow reaction time to DMX
signal
DMX CHANNEL 6 Parameter: DIMMER
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-8 Black-out
9-255 Proportional dimmer
PAN lsb
MOVEMENT SPEED
XR1200 WASH

-
-
ARC 1200
19
DMX CHANNEL 7 Parameter: SHUTTER
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-9 Black-out
10-23 Strobe random speed
24-37 Strobe speed 1 min.
38-51 Strobe speed 2
52-65 Strobe speed 3
66-79 Strobe speed 4
80-93 Strobe speed 5
94-107 Strobe speed 6 max.
108-121 Flash open speed 1 min.
122-135 Flash open speed 2
136-149 Flash open speed 3
150-163 Flash open speed 4 max.
164-177 Flash closed speed 1 min.
178-191 Flash closed speed 2
192-205 Flash closed speed 3
206-219 Flash closed speed 4 max.
220-227 Colours / Macros in black-out
228-233 Pan / Tilt in black-out
234-255 Open
DMX CHANNEL 8 Parameter: COLOUR
DMX range
Value Mid point DMX value
Move
range
(degrees)
Mode Option Function
0-12 White
13-25 Colour 1 (3200° K)
26-38 Colour 2 (5600°K)
39-51
Colour 3
52-64 BiColour 3/4
65-77 Colour 4
78-90 BiColour 4/5
91-103 Colour 5
104-116 BiColour 5/6
117-129 Colour 6
130-142 BiColour 6/7
143-155 Colour 7
156-168 Bicolour 7/8
169-181 Colour 8
182-197 Bicolour 8/white
198-200 Right rotation speed 1 max.
201-203 Right rotation speed 2
204-206 Right rotation speed 3
207-209 Right rotation speed 4
XR1200 WASH

-
ARC 1200
20
210-212 Right rotation speed 5
213-215 Right rotation speed 6
216-218 Right rotation speed 7
219-221 Right rotation speed 8
222-224 Right rotation speed 9 min
225-228 Stop
229-231 Left rotation speed 1 min.
232-234 Left rotation speed 2
235-237 Left rotation speed 3
238-240 Left rotation speed 4
241-243 Left rotation speed 5
244-246 Left rotation speed 6
247-249 Left rotation speed 7
250-252 Left rotation speed 8
253-255 Left rotation speed 9 max.
DMX CHANNEL 9 Parameter: CYAN
DMX range
Value Mid point DMX value
Move
range
(degrees)
Mode Option Function
0-255 Proportional colour
DMX CHANNEL 10 Parameter: MAGENTA
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-255 Proportional colour
DMX CHANNEL 11 Parameter: YELLOW
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-255 Proportional colour
DMX CHANNEL 12 Parameter: SPEED CMY / DIMMER
DMX range
Value
Mid point
DMX value
Move
range
(degrees)
Mode Option Function
0-7 No Function
8-255 Variable speed from max to min
XR1200 WASH