DTS 03.P16.02.01.LED PAR16 LED MR16 BLACK User manual

Technical Datasheet
GB
Made in Italy
PAR16 LED
User’s Manual Rel 1.1
D.T.S. Illuminazione srl - ITALY
http://www.dts-lighting.it
03.P16.02.02.LED
PAR16 LED MR16 LUX
03.P16.02.01.LED
PAR16 LED MR16 BLACK

Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia
non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo
documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso
scritto della D.T.S .
DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche , funzionali o di
design a ciascun proprio prodotto. D.T.S non assume alcuna responsabilità sull’uso o sull’applicazione dei
prodotti o dei circuiti descritti.
The information contained in this publication has been carefully prepared and checked. However, no
responsibility will be taken for any errors. All rights are reserved and this document cannot be copied,
photocopied or reproduced, in part or completely, without prior written consent from D.T.S.
D.T.S. reserves the right to make any aesthetic, functional or design modifications to any of its products
without prior notice. D.T.S. assumes no responsibility for the use or application of the products or circuits
described herein.
Les informations contenues dans le présent manuel ont été rédigées et contrôlées avec le plus grand
soin. Nous déclinons toutefois toute responsabilité en cas d'éventuelles inexactitudes. Tous droits
réservés. Ce document ne peut être copié, photocopié ou reproduit, dans sa totalité ou partiellement,
sans le consentement préalable de .
se réserve le droit d'apporter toutes modifications et améliorations esthétiques, fonctionnelles ou
de design, sans préavis, à chacun de ses produits. décline toute responsabilité sur l'utilisation ou
sur l'application des produits ou des circuits décrits.
D.T.S
D.T.S.
D.T.S.
Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y
controladas. Con todo, no se asume ninguna responsabilidad por eventuales inexactitudes.
Todos los derechos han sido reservados y este documento no puede ser copiado, fotocopiado
o reproducido, total o parcialmente, sin previa autorizaciónescrita de
se reserva el derecho a aportar sin previo aviso cambios y modificaciones de carácter
estético, funcional o de diseño a cada producto suyo. no se asume responsabilidad de
ningún tipo sobre la utilización o sobre la aplicació
n de los productos o de los circuitos descritos.
D.T.S.
D.T.S.
D.T.S.
2PAR16 LED

DESCRIPTION
Protection
Ip20 protection level against the penetration of solids
and liquids
Construction
PAR16 LED is made on aluminium
Standard accessories
MR16 LED lens holder
Weight
0,2 kg
The PAR16 LED is a projector for MR16 LED lamp, with classic shape in 2 sections, square
filterframe, and polished finishing.
The projector is available also with black finishing. (03.P16.02.01.LED)
The projector is provided with a LED lens holder (no MR16 LED lamp unit included).
D.T.S. uses top-quality 99/5 aluminium with a 20/10 thickness for its can bodies, offering greater
strength and incredible resistance to knocks and heat, together with a superior polish.
The edge is not sharp and is therefore safer; it is stronger and conveys extra strength to the
body; it is better finished, making the PAR16 LED more elegant.
The PAR16 LED is fitted with an internal safety cable between rear and front.
The internal plate + clutch system of the PAR16 LED is preferable to other systems that corrode
aluminium or don’t offer a good grip. This ensures safer operation because it permits 0° ÷ 90°
rotation (as requested by international safety standards) and the par can cannot take up
positions that are hazardous for the inflammable surfaces above the par can itself.
Unlike ordinary par cans, the gelatine bearing hooks are spoked to better adhere to the body,
thereby ensuring greater strength and indeformability.
02M00425.01
3PAR16 LED

IMPORTANT SAFETY INFORMATION
Fire prevention:
Never locate the fixture on any flammable surface.
Minimum distance from flammable materials: 10 cm
Safety:
The external surface of the unit may exceed 50°C, never handle the unit until at least 5 minutes
have elapsed since the unit was turned off.
Never install the unit in an enclosed area lacking sufficient air flow.
The ambient temperature should not exceed 40°C and should not be lower than -10°C.
The projector should always be installed with bolts, clamps and other tools that are capable of
supporting the weight of the unit.
-Always use a second safety cable to sustain the weight of the unit in case of the failure of the
main fixing point.
4
1) BRACKET
2) FIXING BRACKET
KNOB
3) REAR SIDE
4) FRONT SIDE
5) LED LENS HOLDER
6) REAR SIDE FIXING
KNOB 6
PAR16 LED

MR16 LED LAMP INSERTING PROCEDURE
5
Place a drop of silicone or other synthetic glue in the 3 holes to fix the LED module to the
dedicated D.T.S. lenses. Never touch the LEDs with hands
Silicone or synthetic glue
Place the MR16 LED unit into PAR16 LED by passing from the front side of the unit.
Fix the MR16 LED unit by using the dedicated LED lens holder
PAR16 LED