Dura Trel CAMELOT PLANTER ARBOR User manual

Dura-Trel, Inc. ~ PO Box 122, Sheboygan Falls, WI 53085 ~ Toll Free 877-258-6020
TOOLS NEEDED
Tape Measure
Variable Speed Drill with
#2 Phillips Bit (recommended) or
Phillips Screwdriver
Straight Blade Screwdriver
Hammer or Mallet
ARBOR SIDE PANEL ASSEMBLY
(Refer to Drawing 1) (Make 2)
On clean flat surface lay one left post so the routed holes are facing up and the screw pilot holes are
facing you. Insert one of the bottom cross rails into the bottom routed slot, and then continue to
insert the seven center cross rails into the top seven routed slots. Set one right post on top of cross
rails and insert each into the routed holes. Lay panel flat, make sure all cross rails are pushed in
tight and fasten with ¾” screws. Snap screw caps over screw heads. Set panel upright and slide
the two 1 x 1 x 60" square rails into the outer holes and the 1 x 1 x 63" square rail into the center
hole.
ARBOR TOP ASSEMBLY
(Refer to Drawing 2)
Lay both side panels on there edge approximately 50" apart, with screw heads facing out and
routed holes for corner braces facing in. Insert one of the 7/8 x 1 ½ x 18” corner brace pieces into
the bottom side of the 1 ½ x 4 x 72” top rail. Working with the side closest to you, slide the 1 ½ x
4 x 72” top rail into the 4" slot on the top of the post. As you slide the top rail into its hole in the
post, insert the corner brace into the 7/8 x 1 ½” hole routed in the post. Do the same procedure
for opposite end of 72" rail. Flip arbor over and repeat for other 72" rail.
The measurement from the longest peak of top rail to the outside of the 2 x 2” leg should be 9”.
Make sure measurement of top rail is correct on both sides. Using 1 ¼” screws fasten corner
braces, top rail and side panels together, snap screw caps over screw heads.
Lay the eight 7/8 x 1 ½ x 41” top cross rails into place on top of the arbor top rails, using the pilot
holes for screws as your guide. Fasten each top cross rails using 1 ¼” screws and snap screw caps
over screw heads.
CAMELOT PLANTER ARBOR
Assembly INSTRUCTIONS

FINISHING TOUCHES INSTALLATION
Apply glue to the inside edges of the 5 3/8” end caps. Push caps on straight; do not slide from
ends. Apply glue to inside edges of 2 x 2” post caps for arbor posts, the arrowhead caps for on top
of 1 x 1 square rails and the 7/8 x 1 ½” end caps for top cross rails on arbor top. Arbor is now
ready for installation on large planter boxes.
INSTALLATION
With straight blade screwdriver, carefully pop off two of the 2 x 2” caps on the long side of each
planter box. Set completed arbor over planter legs.
If the arbor is located in a windy area, we recommend that you use the four ¾” screws and caps to
fasten arbor to planters. Drill small pilot hole in each of the four arbor posts and fasten.
If you encounter missing or defective parts, please contact manufacturer direct at
toll free # below.
Dura-Trel, Inc. ~ PO Box 122, Sheboygan Falls, WI 53085 ~ Toll Free 877-258-6020

Dura-Trel, Inc. ~ PO Box 122, Sheboygan Falls, WI 53085 ~ Toll Free 877-258-6020
PACKING LIST
PARTS CONTAINED:
QTY. PART NO. PART DESCRIPTION
2 40202-69500R 2 x 2 x 69½” RIGHT POST
2 40202-69500L 2 x 2 x 69½” LEFT POST
14 47815-27500
⅞x 1½ x 27½” CENTER RAIL
2 47815-27501
⅞x 1½ x 27½” BOTTOM RAIL
4 50101-48000 1 x 1 x 48” RAIL
2 50101-51000 1 x 1 x 51” RAIL
2 41504-72000 1½ x 4 x 72” ARBOR TOP RAIL
8 47815-41000
⅞x 1½ x 41” TOP CROSS RAIL
4 67815-18000
⅞x 1½ x 18” CORNER BRACE
4 5ECAP-05380
⅞x 1½ x 5⅜” END CAP
1 7GLUE-4OZCN 4 oz PVC GLUE CAN
Hardware Bags Include:
4 7CAPS-0202P 2 x 2” POST CAP
6 7CAPS-0101A 1 x 1” ARROWHEAD CAP
16 7CAPS-7815E
⅞x 1½” END CAP
16 7HDWR-K8034 ¾” KAPPET SCREWS
28 7HDWR-K8125 1¼” KAPPET SCREWS
44 7HDWR-K8000 KAPPET SCREW CAPS
1 CAMELOT PLANTER ARBOR INSTRUCTIONS
NOTE: Some parts may be packed inside of others.
If you encounter missing or defective parts, please contact manufacturer direct at toll free # below.
#11145 Camelot Planter Arbor
add-on kit