Dura Trel 11125 User manual

Dura-Trel, Inc. ~ PO Box 122, Sheboygan Falls, WI 53085 ~ Toll Free 877-258-6020
#11125 6' bench
assembly instructions
Tools needed:
t
Drill with #2 Phillips Bit and
3/32" Drill Bi
2 – 7/16" Wrenches or Sockets
File
BENCH RAIL ASSEMBLY
(Refer to Drawing 1)
Lay out the two bench rails as shown, leaving a 1/8” gap between rails. Set the two
brackets over pilot holes on each end of the rails. Fasten brackets to bench rails using the
¾” screws. Apply glue to inside edges of the 7/8 x 1 ½” molded end caps and slide onto
the ends of the center bench rail. Lay the center bench rail over pilot holes in center of rails
and fasten using 2” Screws.
BENCH ASSEMBLY
(Refer to Drawing 2)
Set one of the bench legs with pilot holes for bolts into the bracket as shown, place a second
leg on the inside of the bracket and loosely fasten to bracket with 4" bolts, washers and
nylock nuts. Set the end of the angled bench brace that has pilot hole for bolt on the inside
of the legs. Fasten with 4" bolt, washers and nylock nuts, place 2 washers in between legs
as you push bolt through.
Repeat for opposite end of bench.
Join the opposite ends of the angled bench braces, so they are overlapping in the center of
the bench. Drill two small pilot holes through the overlapping braces and fasten with
2" screws. Tighten all bolts snugly at this time.
FINISHING
Apply glue to inside edges of the 7/8 x 1 ½ x 11 1/8” end caps and push onto the ends of
the bench, making sure edges are flush. Do not slide end caps on from outside ends
of bench. Do the same with the 7 ¼” end caps for the bottom of the legs.
*Upon completion of bench be sure to file or sand
any sharp edges on the end caps to prevent cuts
and scrapes.*
If you encounter missing or defective parts, please contact manufacturer
direct at toll free # below.

PACKING LIST
#11125 6' bench
PARTS CONTAINED:
Dura-Trel, Inc. ~ PO Box 122, Sheboygan Falls, WI 53085 ~ Toll Free 877-258-6020
QTY. PART NO. PART DESCRIPTION
2 41555-72004W 1½ x 5½ x 72" BENCH RAIL (w/ wood inserts)
4 41555-15750 ½ x 5½ x 15¾" LEG
2 4TBCK-10750 10¾ " BRACKET
1 47815-10250
⅞x 1½ x 10¼" CENTER BRACE
2 57815-24750
⅞x 1½ x 24¾" ANGLE BRACE
2 5ECAP-11180
⅞x 1½ x 11⅛" END CAP
4 5ECAP-06000
⅞x 1½ x 6" LEG END CAP
1 7GLUE-4OZCN 4 oz PVC GLUE CAN
Hardware Bag Includes:
2 7CAPS-7815E
⅞x 1½" MOLDED END CAPS
6 7HDWR-06200 2" SCREW
16 7HDWR-06034 ¾" SCREW
6 7HDWR-14400 ¼ x 4" BOLT
6 7HDWR-14NUT NYLOCK NUT
16 7HDWR-14WSH WASHERS
6’ BENCH INSTRUCTIONS
NOTE: Some parts may be packed inside of others.
If
y
ou encounter missin
g
or defective
p
arts
,
p
lease contact manufacturer direct at toll free # below.