Dura Trel winchester TRELLIS User manual

#11174M
winchester TRELLIS
Assembly INSTRUCTIONS
Dura-Trel, Inc. ~ PO Box 122, Sheboygan Falls, WI 53085 ~ Toll Free 877-258-6020
TOOLS REQUIRED
Drill with #2 Phillips Bit or
Phillips Screwdriver
Super or Crazy Glue
Hammer or Mallet
TRELLIS ASSEMBLY
(Refer to Drawing)
On clean flat surface lay the left post so that screw pilot holes are facing toward you and the
⅞x 1½" holes are facing up. Insert the ⅞x 3 x 56¾” rail and the ⅞x 1½x 56¾” bottom rail into
holes at the bottom of the post; then continue inserting the ten center cross rails into the remaining
ten routed holes (make sure screw pilot holes on all ⅞x 1½x 56¾” cross rails are facing the same
direction as the screw pilot holes of the left post). Take the right post and insert the opposite ends
of the cross rails into the routed holes, starting on the end with the bottom rails. Set trellis up;
slide the 1 x 1 x 87" square rail into the middle spot. Slide the remaining 1 x 1” rails in the outer
spots with the longer rails towards the middle of the trellis. Lay the trellis flat. Make sure the
cross rails are completely inserted into both posts and fasten with screws. Snap screw caps over
screw heads.
Apply glue to the inside edges of the 2 x 2” caps and arrowhead caps. Place 2 x 2” caps on the top
of posts and the arrowhead caps on top of the 1 x 1” square rails. Trellis is now ready for
installation.
INSTALLATION
(Refer to small inlay drawing) (Hardware for installation is in a separate bag.)
The Winchester Trellis is recommended for wall mounting and materials are provided for this type
of installation. There are two pilot holes in each post for wall mounting. (Put the small clear
backers onto the 6" screws so the screw heads fits into backers.) Place the 3” spacer tube between
wall and trellis and fasten with the 6" screw & backer combination. Snap the larger size screw caps
over backers
If you encounter missing or defective parts, please contact manufacturer direct at
toll free # below.

Dura-Trel, Inc. ~ PO Box 122, Sheboygan Falls, WI 53085 ~ Toll Free 877-258-6020
PACKING LIST
QTY. PART NO. PART DESCRIPTION
1 40202-M84005L 2 x 2 x 84” LEFT POST
1 40202-M84005R 2 x 2 x 84” RIGHT POST
10 47815-M56001
⅞x 1½ x 56¾” CENTER CROSS RAIL
1 47815-M56002
⅞x 1½ x 56¾” BOTTOM CROSS RAIL
1 67803-M56000
⅞x 3 x 56¾” RAIL
1 60101-M87000 1 x 1 x 87” RAIL
2 50101-M85000 1 x 1 x 85” RAIL
2 50101-M83000 1 x 1 x 83” RAIL
2 50101-M81000 1 x 1 x 81” RAIL
1 HWBAG-M22GAT GROUND ANCHOR HARDWARE BAG
Hardware Bags Includes:
2 7CAPS-M0202P 2 x 2” POST CAP
7 7CAPS-M0101A 1 x 1” ARROWHEAD CAP
19 7HDWR-K8034 ¾” KAPPET SCREW
19 7HDWR-MK8000 KAPPET SCREW CAP
4 50034-M02500 ¾ x 2½” ANCHOR TUBE
4 7HDWR-10600 #10 x 6” ANCHOR SCREW
4 7HDWR-10001 #10 SCREW BACKER
4 7HDWR-M10000 #10 SCREW CAP
WINCHESTER TRELLIS INSTRUCTIONS
NOTE: Some parts may be packed inside of others.
If you encounter missing or defective parts, please contact manufacturer direct at toll free # below.
#11174M Winchester trellis (mocha)
Parts Contained: