Dura Trel 11119/09 User manual

Model# 11119/09 Assembly Instructions
Part # Description
max 5 x 3.5 1⅞ x 1½ x 60½" Left Leg
2⅞ x 1½ x 60½" Right Leg
3⅞ x 1½ x 28" Top/Bottom Cross Rail
4⅞ x 1½ x 28" Center Cross Rail
5⅝ x 53" Tube
6⅞ x 1½ x 36 / 48" Arbor Top
7¾ x 27 ⅞" Tube
8⅞ x 1½ x 12" Flared Ground Anchor
9 Hardware Bag (includes:)
¾" Painted Screw
PLEASE READ THROUGH BEFORE BEGINNING ASSEMBLY.
IMPORTANT: Check boxes for Contents Listed
Check inside of parts as some parts are packaged
inside of others
In the event of missing, damaged or defective parts
please call our customer service dept. at 1-877-258-6020
When assembling components, place on a clean, flat
non-abrasive surface to avoid scratches
…
Battery or Electric Drill with #2 phillips bit (recommended)
or
…Phillips Screwdriver
…Tape Measure
…
Rubber Mallet or Hammer (optional but recommended)
150 Birch Road
P.O. Box 122
Sheboygan Falls, WI 53085
2
4
Qty
2
3/4' Grapevine Arbor
4
1
2
5
2
10
General Information
22
www.dura-trel.com
[e-mail]
Tools Required
1-877-258-6020
1

150 Birch Road
P.O. Box 122
Sheboygan Falls, WI 53085
1-877-258-6020
2
www.dura-trel.com
[e-mail]
Please call manufacturer direct with questions concerning missing or defective parts at Toll Free:
877
-258-6020.
Dura
-trel,
Inc. products are warranted to be free from manufacturing defects resulting in delaminating,
peeling, flaking, corroding, cracking, crazing, or extreme amounts of fading or bleaching causing the
PVC to change to its natural color for a period of 20 years from the date of purchase.
Normal weathering is defined as exposure to sunlight and extremes of weather and atmosphere which
will cause any colored surface to gradually fade.
CONDITIONS NOT COVERED BY THIS WARRANTY:
A. Physical abuse, misuse, neglect, or improper storage.
B. Improper installation or installation not in strict adherence to the instructions written by Dura
-Trel,
Inc.
C. This warranty does not apply if materials are painted, varnished, or coated with any substance.
D. Dura
-Trel, Inc. is not responsible for damages to product during shipping.
E. Damage attributable to atmospheric pollutants, hail, lightning, hurricane, tornado, wind borne
objects, earthquake, fire, mildew, casualty, act of God, building or ground settlement, or subjection to
stress or weight.
CLAIMS AND REMEDIES:
If a Dura
-Trel, Inc. product is determined to have a manufacturing defect which is covered by this
warranty, Dura
-Trel, Inc. will replace the material containing the defect (labor no included) F.O.B from
the point of manufacture. Dura
-trel, Inc. will not be responsible for any cost incurred in the removal or
reinstallation of the product.
Important:
An claims must be sent to the following address and should describe the defect claim.
Dura-Trel, Inc., P.O. Box 122, Sheboygan Falls, WI 53085
Dura
-Trel, Inc. reserves the right to discontinue or change its design, and or color. If the original color
or style is not available, Dura
-Trel, Inc. shall have the right to substitute a product designated by Dura-
Trel, Inc.
Dura
-Trel, Inc. shall not be liable for any incidental, special, or consequential damages arising out of
the use of these products
Warranty Statement
20 Year Guarantee

3
3/4' Grapevine Arbor
On clean flat surface lay out one 60½" left leg (part 1). Insert 28" center cross rail (part 4) into middle hole and one 28"
top/bottom cross rail (part 3) into hole at bottom of leg. Insert 53" tubes (part 5) through holes in center cross rail and
into top/bottom cross rail. Insert remaining top/bottom cross rail (part 3) into remaining hole in leg, inserting 53" tubes
into top/bottom cross rail. Insert free ends of 28" cross rails into one 60½" right leg (part 2). Using six ¾" screws, screw
together arbor panel. Be sure that all parts are fully inserted into legs before.
Repeat this step to make second arbor panel.

3/4' Grapevine Arbor
4
Insert five 27¾" tubes (part 7) into one bent arbor top (part 6). Insert free ends of tubes into remaining bent arbor top
(part 6). Using six ¾" screws, screw together arbor top. Be sure tubes are fully inserted into arbor tops before. fastening
Insert ends of arbor top into flared ends of each arbor panel to complete arbor.
INSTALLATION
In desired location set arborin place and mark where ground anchors (part 8) will need to be inserted. Using a block of
wood to protect flared edges of ground anchors; pound the anchors into place. (If ground is extremely hard, loosen or
soak soil before inserting ground anchors). Set arbor into ground anchors and fasten using remaining four ¾" screws.