Dura Trel 11190 Elmwood Trellis User manual

#11190 Elmwood TRELLIS
ASSEMBLY INSTRUCTIONS
TOOLS NEEDED
Drill with #2 Phillips drill bit or
Phillips Screwdriver
Super or Crazy Glue
Hammer or Mallet
TRELLIS ASSEMBLY
(Refer to Drawing 1)
On clean flat surface lay the 2 x 2 x 74” left post with the routed holes are facing up and the screw
pilot holes are facing you. Insert one of the ⅞x 1½x 22” top/bottom rails into the bottom routed
hole, then continue to insert nine ¼x 1½x 22”slats into the middle slots. Set the 2 x 2 x 74”
right post on top of the previous assembly and insert each rail into the routed holes. Lay trellis flat,
starting at the top right of the trellis, take one ¼x 1½x 66” slat and weave it above, then below
each of the ¼x 1½x 22” slats, insert into right slot of the bottom rail. Weave left
¼x 1½x 66” slat in the opposite direction of the right slat, and insert into the left slot in the
bottom rail. Spread the top of the panel just enough to insert the second ⅞x 1½x 22”
top/bottom rail, inserting the free end of the slats into the into the top/bottom rail. Make sure all
parts are inserted completely into both posts and fasten with screws. Snap screw caps over screw
heads. Finally, apply household glue to the corners of each
2 x 2” post cap and place on top of each post. Trellis is now ready for installation (See Ground
Anchor Hardware Bag).
If you encounter missing or defective parts, please contact manufacturer direct at
toll free # below.
Dura-Trel, Inc. ~ PO Box 122, Sheboygan Falls, WI 53085 ~ Toll Free 877-258-6020

Dura-Trel, Inc. – PO Box 122, Sheboygan Falls, WI 53085 – Toll Free 877-258-6020
PACKING LIST
PARTS CONTAINED:
QTY. PART NO. PART DESCRIPTION
1 40202-74003L 2 x 2 x 74” LEFT POST
1 40202-74003R 2 x 2 x 74” RIGHT POST
2 47815-22002
⅞x 1½ x 22” TOP/BOTTOM RAIL
9 61415-22000 ¼ x 1½ x 22” SLAT
2 61415-66000 ¼ x 1½ x 66” SLAT
1 HWBAG-22GAT GROUND ANCHOR HARDWARE BAG
Hardware Bag Includes:
2 7CAPS-0202P 2 x 2 " POST CAP
4 7HDWR-K8125 1¼" KAPPET SCREW
4 7HDWR-K8000 KAPPET SCREW CAP
NOTE: Some parts may be packed inside of others.
If you encounter missing or defective parts, please contact manufacturer direct at toll free #
below.
#11190 elmwood TRELLIS

Option 1 (soft ground)
Slide one 16” steel L-channel ground anchor
into bottom of each post. Slide ground anchor
up to bottom cross rail. Using two 1” self-
tapping white-head screws per post, screw
post to ground anchor (figure 1). When
fastening, use one screw per side where
ground anchor meets post. For added support
fasten screws with at least two inches vertically
between them.
Option 2 (hard ground)
Measure distance between posts and mark
ground accordingly. Pound 16” steel L-
channel ground anchors into ground according
to measurements and basic layout (figure 2),
leaving about 4 inches of ground anchor
exposed. When pounding into ground, use
block of wood to prevent ground anchor from
bending.
Slide trellis over ground anchors. Using two 1”
self-tapping white-head screws per post screw
post to ground anchor (figure 1). When
fastening, use one screw per side where
ground anchor meets post. For added support
fasten screws with at least two inches vertically
between them.
Option 3 (permanent installation)
Measure distance between posts and mark
ground accordingly. Dig holes 12” deep
according to measurements and basic layout
(figure 2). Fill with cement and place 16” steel
L-channel ground anchors in wet cement. Be
sure that ground anchors are straight and in
accordance with measurements of trellis posts.
Allow cement to dry. NOTE: There is very little
room for error with this installation method.
Slide trellis over ground anchors. Using two 1”
self-tapping white-head screws per post screw
post to ground anchor (figure 1). When
fastening, use one screw per side where
ground anchor meets post. For added support
fasten screws with at least two inches vertically
between them.
FIGURE 1
Ground Anchor
Assembly
FIGURE 2
Ground Anchor
Basic Installation Layout
2” sq. post trellis
ground anchor
Assembly & installation Instructions
Description Qty
16” L-channel Ground Anchor 2
1” Self-tapping White-head Screws 4
Parts List: