Dura Trel PROVIDENCE ARBOR User manual

Model# 11178 (M) Assembly Instructions
Part # Description
max 5 x 3.5 1
2" sq. x 84" Left Post
2 2" sq. x 84" Right Post
3⅞ x 1½ x 22" Top/Bottom Cross Rail
4⅞ x 1½ x 22" Center Cross Rail
5 ¼ x 1½ x 59½" Vertical Slat
6 1½ x 4 x 64" Arbor Top
7⅞ x 1½ x 28" Arbor Top Cross Rail
8⅞ x 1½ x 16" Corner Brace
95 ⅜" Arbor Top End Cap
10 Hardware Bag (includes:)
2" sq. Post Cap
⅞ x 1½" End Cap
1¼" Painted Screw
Super Glue Tube
PLEASE READ THROUGH BEFORE BEGINNING ASSEMBLY. 11
Arbor Ground Anchor Kit (includes:)
IMPORTANT: Check boxes for Contents Listed 16" Steel Ground Anchor (L-Shaped)
Check inside of parts as some parts are packaged #8 - 1" Painted Self Tapping Screw
inside of others
In the event of missing, damaged or defective parts
please call our customer service dept. at 1-877-258-6020
When assembling components, place on a clean, flat
non-abrasive surface to avoid scratches
…
Battery or Electric Drill with #2 phillips bit
…Tape Measure
…
Hammer or Rubber Mallet (recommended)
150 Birch Road
P.O. Box 122
Sheboygan Falls, WI 53085
2
4
Qty
2
Providence Arbor
4
4
2
7
16
4
14
General Information
38
1
4
1
www.dura-trel.com
[e-mail]
Tools Required
1-877-258-6020
1
1
4
8

150 Birch Road
P.O. Box 122
Sheboygan Falls, WI 53085
1-877-258-6020
2
www.dura-trel.com
[e-mail]
Please call manufacturer direct with questions concerning missing or defective parts at Toll Free:
877
-258-6020.
Dura
-trel,
Inc. products are warranted to be free from manufacturing defects resulting in delaminating,
peeling, flaking, corroding, cracking, crazing, or extreme amounts of fading or bleaching causing the
PVC to change to its natural color for a period of 20 years from the date of purchase.
Normal weathering is defined as exposure to sunlight and extremes of weather and atmosphere which
will cause any colored surface to gradually fade.
CONDITIONS NOT COVERED BY THIS WARRANTY:
A. Physical abuse, misuse, neglect, or improper storage.
B. Improper installation or installation not in strict adherence to the instructions written by Dura
-Trel,
Inc.
C. This warranty does not apply if materials are painted, varnished, or coated with any substance.
D. Dura
-Trel, Inc. is not responsible for damages to product during shipping.
E. Damage attributable to atmospheric pollutants, hail, lightning, hurricane, tornado, wind borne
objects, earthquake, fire, mildew, casualty, act of God, building or ground settlement, or subjection to
stress or weight.
CLAIMS AND REMEDIES:
If a Dura
-Trel, Inc. product is determined to have a manufacturing defect which is covered by this
warranty, Dura
-
Trel, Inc. will replace the material containing the defect (labor not included) F.O.B from
the point of manufacture. Dura
-trel, Inc. will not be responsible for any cost incurred in the removal or
reinstallation of the product.
Important:
An claims must be sent to the following address and should describe the defect claim.
Dura-Trel, Inc., P.O. Box 122, Sheboygan Falls, WI 53085
Dura
-Trel, Inc. reserves the right to discontinue or change its design, and or color. If the original color
or style is not available, Dura
-Trel, Inc. shall have the right to substitute a product designated by Dura-
Trel, Inc.
Dura
-Trel, Inc. shall not be liable for any incidental, special, or consequential damages arising out of
the use of these products
Warranty Statement
20 Year Guarantee

3
Providence Arbor
Starting at bottom of 84" left post (part 1) insert one 22" top/bottom cross rail (part 3) and eight 22" center
cross rails (part 4) into holes. DO NOT insert remaining top/bottom cross rail into top hole at this time.
Insert free ends of cross rails into 84" right post (part 2). Slide two 59½" vertical slats (part 5) through each
center cross rail and into bottom cross rail. Separate top of posts just enough to insert remaining 22"
top/bottom cross rail (part 3) into top hole of each post, inserting free end of vertical slats into top cross
rail. Using three 1¼" screws per post, fasten together arbor side. Be sure all parts are fully inserted into
posts before securing.
REPEAT using remaining posts and cross rails to make second arbor panel.

Providence Arbor
4
Instruction Text
Insert two 16" corner braces (part 8) into each 64" arbor top (part 6). Slide ends of arbor top rail through
holes at top of post, inserting corner braces into posts. Measure 9 inches from tips of arbor top rails and
slide posts so outside of post in 9 inches from end of arbor top rails. Using three 1¼" screws per post, fasten
together posts, arbor top rails and corner braces.
Using two 1¼" screws per part, fasten all seven arbor top cross rails (part 7) to arbor top rails, using small
pilot holes to line up screws.
Using included super glue tube, glue
⅞ x 1½" end caps onto ends of each arbor top cross rail. Glue four 5⅜"
arbor top end caps (part 9) onto ends of arbor top rails. Glue four 2" sq. post caps onto tops of post.

11178
Providence Arbor
1
2" sq. x 84" PVA Left Post 2.00
2
2" sq. x 84" PVA Right Post 2.00
3
⅞ x 1½ x 22" PVT Top/Bottom 4.00
4
⅞ x 1½ x 22" PVT Center Rai 16.00
5
¼ x 1½ x 59½" Slat 4.00
6
1½ x 4 x 64" PVA Arbor Top 2.00
7
⅞ x 1½ x 28" PVA Top Cross 7.00
8
⅞ x 1½ x 16" Rail -Thin 4.00
9
5 ⅜" CMA Angled End Cap 4.00
10
Hardware Bag 1.00
2" sq." Post Cap 2.00
⅞ x 1½" End Cap 14.00
1¼" Painted Screw 38.00
Super Glue Tube 1.00
Grnd Anch - Arbor (2 x 2) 1.00
#8 - 1" Self Tapping White He 8.00