Dura Trel 11235 User manual

#11235 COMPOST BIN
ASSEMBLY INSTRUCTIONS
TOOLS NEEDED:
Drill with #2 Phillips Bit (recommended) or
Phillips Screwdriver
Super or Crazy Glue
BACK PANEL ASSEMBLY
(Refer to Right Side of Drawing 1)
Lay the 2 x 2 x 30½” middle back post on a clean, flat surface with the screw pilot holes facing up. Slide eight of the ⅞x 3 x 53”
rails through the routed holes. The 2 x 2 x 30½” middle back post should be in the center of all of the ⅞x 3 x 53”. Slide the
two 2 x 2 x 30½” back end posts on each end of the ⅞x 3 x 53” rails with the screw pilot holes facing up and to the outside.
Fasten with ⅝" screws and snap screw caps over screw heads. (Be sure the 2 x 2 x 30½” middle back post is centered
before fastening with screws.)
FRONT PANEL ASSEMBLY
(Refer to Left Side of Drawing 1)
Lay the 2 x 2 x 30½” middle front post on a clean, flat surface with the screw pilot holes facing up. Slide the remaining ⅞x 3 x
53” rail through the bottom ⅞x 3” routed hole and the ⅞x 1½ x 53” through the top routed hole. The 2 x 2 x 30½” middle
front post should be in the middle of the two rails. With the
⅞x 1½ x 53” on top, the ⅞x 3 x 53” rail on the bottom and the screw pilot holes of the 2 x 2 x 30½” front middle post facing
up; slide the 2 x 2 x 30½” front right post on the right side of the assembly and the
2 x 2 x 30½” front left post on the left side of the assembly with the screw pilot holes facing up and to the outside. Fasten with
⅝" screws and snap screw caps over screw heads. (Be sure the 2 x 2 x 30½” middle front post is centered before
fastening with screws.)
COMPOST BIN ASSEMBLY
(Refer to Drawing 2)
With back panel laying flat with routed openings facing up; slide the ⅞x 3 x 24¼” angled side rails completely into both back
end posts and the two ⅞x 1½ x 24¼” angled middle rails into the back middle post. Be sure that the angled end of each rail is
inserted into the back posts. Fasten the ⅞x 3 x 24¼” angled side rails with ⅝" screws and the ⅞x 1½ x 24¼” angled middle
rails with 1¼” screws. Snap screw caps over screw heads. Next slide front panel onto side rails making sure there is
enough gap inside front posts to easily slide removable front rails in and out. Fasten the side rails with ⅝" screws
and the middle rails with 1¼” screws, as before and snap screw caps over screw heads. Apply glue to inside edges of 2 x 2" post
caps and place on top of posts.
Insert ⅞x 3 x 25¼” Front Removable Rails by sliding into the front left and front right post completely then slide into the front
middle post, adjust so handle cutouts line up evenly. (NOTE: If the front middle post is NOT centered properly, the
front rails will not fit on both sides.)
If you encounter missing or defective parts, please contact manufacturer direct at toll free #
below.
Dura-Trel, Inc. ~ PO Box 122, Sheboygan Falls, WI 53085 ~ Toll Free 877-258-6020

Dura-Trel, Inc. – PO Box 122, Sheboygan Falls, WI 53085 – Toll Free 877-258-6020
PACKING LIST
PARTS CONTAINED:
QTY. PART NO. PART DESCRIPTION
1 40202-30500L 2 x 2 x 30½” LEFT FRONT POST
1 40202-30500R 2 x 2 x 30½” RIGHT FRONT POST
2 40202-30501 2 x 2 x 30½” BACK POST
1 40202-30502 2 x 2 x 30½” FRONT MIDDLE POST
1 40202-30503 2 x 2 x 30½” BACK MIDDLE POST
14 47803-25250
⅞x 3 x 25½”" FRONT RAIL (w/handle cutout)
16 57803-24250
⅞x 3 x 24¼” ANGLED SIDE RAIL
2 57815-24250
⅞x 1½ x 24¼" ANGLED MIDDLE RAIL
9 57803-53000
⅞x 3 x 53” RAIL
1 57815-53000
⅞x 1½ x 53" RAIL
1 HARDWARE BAG
If you encounter missing or defective parts, please contact manufacturer direct at toll free # below.
#11235 DoUBLE WIDE compost bin