DXV Victorian D35402001 User manual

- 1 -
INSTALLATION INSTRUCTIONS
SAVE FOR FUTURE USE
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2013
In the United States:
DXV by American Standard
One Centennial Avenue
Piscataway, New Jersey 08855
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.DXV.com
In Canada:
DXV by American Standard
5900 Avebury Road
Mississauga, Ontario
L5R 3M3
Canada
Toll Free: 1-800-387-0369
Local: 905-306-1093
Fax: [phone]
www.DXV.ca
In Mexico:
DXV by American Standard
Via Morelos 330
Col. Santa Clara Coatitla
Ecatepec, Estado de México 55540
Toll Free: 01-800-8391200
www.DXV.mx
Thank you for selecting DXV by American Standard. To ensure that
your installation proceeds smoothly, please read these instructions
carefully before you begin.
RECOMMENDED TOOLS AND MATERIALS
Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing,
supply stores. It is essential that the tools and materials be on hand before work is begun.
M965535 Rev. 1.3 (4/15)
Single Control Faucet
Model D35402000
Single Control Faucet with Spray
Model D35402001
Victorian
Single Control Kitchen Faucet
ROUGHING-IN DIMENSIONS:
• For reference
Plumbers' Putty or CaulkingAdjustable Wrench
Phillips Screwdriver
Channel Locks Flat Blade Screwdriver
8-5/8"
(219 mm)
12"
(305 mm)
5-7/8"
(149 mm)
2"
(51mm)
3-7/8"
(98 mm)
5-1/4"
(133 mm)
24"
(610 mm)
2-3/4"
(70 mm)
8-7/8"
(225 mm)
1-3/4"
(44 mm)
1-3/4"
(44 mm)
1"
(25 mm)
1-1/4"
(32 mm)
2-1/4" D.
(57 mm)
NOTE: Bore hole size is 1-3/8"
3/8"
COMPRESSION
2-3/16"
(53.8 mm)

- 2 - M965535 Rev. 1.3 (4/15)
1INSTALL FITTING
• Make certain the O-RING (2) is properly seated in recess of FAUCET BASE (3).
• Insert HOSES (4) and SHANK (9) through center hole of sink or mounting surface.
• Assemble three BRASS SCREW (8) into the FIXATION RING (7).
• Assemble SUPPORT PLATE (5) METAL WASHER (6), and
FIXATION RING (7) onto SHANK (10) from underside of sink.
Hand tighten the FIXATION RING (7) and check that
FAUCET (1) is centered.
• Use a screwdriver to tighten SCREWS (8) on FIXATION RING (7).
Work your way around FIXATION RING (7), tightening the SCREWS (8)
slightly each time until all are snug to ensure even pressure.
CAUTION Turn off hot and cold wate
supplies before beginning.
5
86
7
4
9
2
3
1

- 3 - M965535 Rev. 1.3 (4/15)
5
3
4
TEST INSTALLED FAUCET
INSTALL HOSE AND SPRAY (Model D35402.001)
MAKE WATER SUPPLY CONNECTIONS
• Move HANDLE (1) into “off” position.
• Turn on water supplies and check all connections for leaks.
• Pull HAND SPRAY (2) from HOLDER (3) and disconnect HAND SPRAY (2)
from HOSE (4). Pull HOSE (4) (HOSE should pull approximately
2 feet)and direct open HOSE END (4) into sink.
• Operate handle, in COLD and HOT positions, to ush
water lines thoroughly.
• Connect HAND SPRAY (2) to HOSE END (4). Place
HAND SPRAY (2) back into HOLDER (3), operate
HANDLE (1) and check all connections for leaks.
• Check HAND SPRAY (2) operation with faucet on
push front of LEVER (5) for a broad cleansing spray.
TROUBLE SHOOTING
Low water flow from faucet:
• Remove AERATOR (6) and clean if necessary.
Pull-Out Spray will not remove from faucet freely:
• Check that pull-out spray hose is not obstructed with
plumbingconnections or ttings under faucet.
• Remove LARGE WASHER (5) and SMALL WASHER (6) FROM SPRAY HOSE (7).
Feed the small end of the SPRAY HOSE (7) through the SPRAY HOLDER (1).
Install the SMALL WASHER (6) into the COUPLING (9) of the spray connection
on faucet. Connect HOSE END (7) to COUPLING (9).
• Install the LARGE WASHER (5) into the COUPLING (10) for the HAND SPRAY (8)
and hand tighten. Place the HAND SPRAY (8) into the Spray holder (1).
• Turn off hot and cold water supplies before beginning.
• Connect FLEXIBLE SUPPLIES (6, 7) directly to wall supplies. Connection on tting
supplies are 3/8" compression. Connect left supply (Marked Red) to Hot and
right supply (Marked Blue) to Cold wall supply. Use adjustable wrench to
tighten connections. Do not over tighten.
• Faucet supplies are 21" long from faucet base.
Note: If additional supply length is required, installer must purchase
additional parts separately.
Important: If SUPPLY HOSES (6, 7) are too long, loop asillustrated to avoid kinking.
• Remove RUBBER WASHER (5) and FIBER WASHER (6) FROM SPRAY HOSE (7). Feed
the small end of the SPRAY HOSE (7) through the SPRAY HOLDER (1). Install the FIBER
WASHER (6) into the COUPLING (9) of the spray connection on faucet. Tighten with two
wrenches to make a water tight connection.
• Install the RUBBER WASHER (5) into the COUPLING (10) for the HAND SPRAY (8) and
hand tighten. Place the HAND SPRAY (8) into the Spray holder (1).
2INSTALL SPRAY HOLDER (Model D35402.001)
• Apply a bead of putty to the underside lip of SPRAY HOLDER (1).
• Place the SPRAY HOLDER (1) into the appropriate mounting hole.
Assemble the RUBBER WASHER (2), BRASS WASHER (3) and
LOCK NUT (4) onto the shank of SPRAY HOLDER (1). From
below tighten LOCK NUT (4) to secure SPRAY HOLDER (1).
9
PUTTY
1
10
5
8
2
3
4
COLD
HOT
SUPPLY STOPS
6
7
6
7
2
3
5
1
4
6

- 4 - M965535 Rev. 1.3 (4/15)
Replace the “YYY” with
appropriate finish code
POLISHED CHROME 100
CARBON BRONZE 110
ULTRA STEEL 355
Victorian
Single Control
Kitchen Faucet
MODEL NUMBERS
Single Control Faucet
D35402000
Single Control Faucet
with Spray
D35402001
H962078.191
CARTRIDGE NUT
M964668-YYY0A
DECORATIVE RING KIT
H961342.XXX
HANDLE KIT
H962019.XXX
HANDLE FIXATION
M964406-0070A
CARTRIDGE
M964667-0070A
MOUNTING KIT
M964741-0070A
SPOUT SET SCREW
M964670-0070A
SWING SPOUT SEAL KIT
H960567.XXX
AERATOR
M964744-007A
DIVERTER
M964669-YYY0A
ESCUTCHEON KIT
M964954-1000A
NYLON SPRAY HOSE
WITH SEALS
M964743-YYY0A
SIDE SPRAY
H960015.XXX
SIDE SPRAY SUPPORT