DXV Rem D3510010C User manual

- 1 -
INSTALLATION INSTRUCTIONS
In the United States:
DXV
One Centennial Avenue
Piscataway, New Jersey 08855
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.DXV.com
In Canada:
DXV
5900 Avebury Road
Mississauga, Ontario
L5R 3M3
Canada
Toll Free: 1-800-387-0369
Local: 905-306-1093
Fax: [phone]
www.DXV.ca
In Mexico:
DXV
Via Morelos 330
Col. Santa Clara Coatitla
Ecatepec, Estado de México 55540
Toll Free: 01-800-8391200
www.DXV.mx
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2017
SAVE FOR FUTURE USE
Thank you for selecting DXV. To ensure that your
installation proceeds smoothly, please read these
instructions carefully before you begin.
RECOMMENDED TOOLS AND MATERIALS
Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing
supply stores. It is essential that the tools and materials be on hand before work is begun.
M965700 Rev. 1.1 (4/17)
Monoblock
Model D3510010C
Monoblock Vessel
Model D3510015C
Rem®Single Lever Faucet
Plumbers' Putty or Caulking
Phillips Screwdriver
Channel LocksTubing Cutter Flat Blade Screwdriver Adjustable Wrench
Basin Wrench
ROUGHING-IN DIMENSIONS:
• For reference
MOUNTING
SURFACE
1-1/2"
(38 mm)
8-1/4"
(210 mm)
11-7/8"
(302 mm)
11-3/8"
(289 mm)
1-3/16" MAX. (30 mm)
5/8" MIN. (15 mm)
NOTE: MOUNTING HOLE 1-3/8" DIA. (35 mm)
MOUNTING
SURFACE
1-1/4" O.D.
(32 mm)
2" MAX.
(51mm)
2-7/16"
(65 mm)
20"
(508 mm)
2"
(51 mm)
10" MAX.
(254 mm)
3/8" (10mm)
SUPPLIES
6"
(152 mm)
1-1/2"
(38 mm)
MOUNTING
SURFACE
7-1/8"
(181 mm)
3-1/2"
(89 mm)
6-3/4"
(171 mm)
5-3/4"
(146 mm)
1-1/4" O.D.
(32 mm)
2" MAX.
(51 mm)
2-7/16"
(65 mm)
10" MAX.
(254 mm)
3/8" (10 mm)
SUPPLIES
1-3/16" MAX. (30 mm)
5/8" MIN. (15 mm)
20"
(508 mm)
2"
(51 mm)

- 2 - M965700 Rev. 1.1 (4/17)
1
• Install O-RING SEAL (1) into bottom of faucet.
• Feed FLEXIBLE FAUCET SUPPLIES (2) SHANKS (3) and CABLE CONNECTOR (4) through the
mounting hole of lavatoryor mounting surface.
INSTALL VESSEL OR MONOBLOCK FAUCETS
CAUTION Turn off hot and cold water
supplies before beginning.
1
2
3
5
4
6

- 3 - M965700 Rev. 1.1 (4/17)
2
3
4
6
5
POP-UP DRAIN
REMOVE FLANGE
INSTALL DRAIN FROM
BELOW FIXTURE
FLANGE GASKET AND POP-UP KNOB
TIGHTEN LOCKNUT
• Remove CLEAR PLASTIC COVER (1).
• Remove CARDBOARD SPACER (2) from
under DRAIN POP-UP (3).
• Tighten TAILPIECE (4) on DRAIN BODY
before installing DRAIN BODY. Fig. B.
• Thread FLANGE (1) counter-clockwise and
remove FLANGE (1) and FOAM GASKET (2)
from drain body. Fig. A.
• Thread LOCKNUT (3) clock-wise to bottom
of drain body. Push GASKET (4) down
against LOCKNUT (3). Fig. B.
• From under side of SINK
install DRAIN BODY (1) up
through drain outlet.
Note: No plumber’s putty
or caulk is required.
The CABLE ATTACHMENT
POINT (2) must face
towards the rear of
the SINK.
• Install FOAM GASKET (3) and
FLANGE (4) onto drain body
from above SINK and tighten
FLANGE (4) rmly.
• Check DRAIN FLANGE in SINK to ensure that
WHITE FOAM GASKET (3) is fully compressed
and not visible. Fig. A.
• POP-UP KNOB (1) must be fully down.
Fig. B.
• Tighten LOCKNUT (1) rmly with
Adjustable Wrench or Channel Locks.
2
3
1
DRAIN
BODY
4
Fig. A. Fig. B.
3
4
2
1
Fig. A. Fig. B.
WHITE FOAM
GASKET
NOT VISIBLE
DRAIN
FLANGE 1
DOWN
Fig. A.Fig. A. Fig. B.
REAR OF SINK
DRAIN
OUTLET
2
1
3
4
1

- 4 - M965700 Rev. 1.1 (4/17)
7
8
9
ATTACH CABLE CONNECTOR
CHECK OPERATION OF POP-UP
MAKE WATER SUPPLY AND WASTE CONNECTIONS
• Thread CABLE CONNECTOR (1) clockwise
onto DRAIN BODY CONNECTION (2) and
hand tighten. Fig. A.
Your new POP-UP DRAIN installation is
now complete. Fig. B.
Note: Tailpeice on pop-up drain is 1-1/4" O.D.
Fig. B.
• Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes.
Note: If STOPPER (2) does not open and close properly then refer to the
“troubleshooting section” of these instructions.
• Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies.
Connection on tting supplies are 3/8" compression. Connect
left SUPPLY (1) to Hot (Marked with a Red Band) and right supply
to COLD (2) wall supply.
• Faucet supplies are 20" long from faucet base.
Note: If additional supply length is required, installer must
purchase additional parts separately.
Important: If SUPPLY HOSES (1, 2) are to long, loop as
illustrated to avoid kinking.
• Connect 1-1/4" O.D. tailpiece on POP-UP DRAIN to
waste outlet.
2
1
1-1/4” O.D.
Fig. A. Fig. B.
1
2
1
APPROX. 20"
2
COLD
HOT
3/8" COMPRESSION
RED
BAND
BLUE
BAND

- 5 - M965700 Rev. 1.1 (4/17)
10
• With HANDLE (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks.
• Remove AERATOR (3). First loosen aerator set screw with HEX WRENCH (4) supplied. Pull out AERATOR (3) with
AERATOR KEY (5).
• Operate HANDLE (1) to ush water lines thoroughly.
• Replace AERATOR (3) and tighten set screw.
CHECK DRAIN CONNECTIONS
• Operate POP-UP KNOB (6) and ll lavatory with water. Check that DRAIN STOPPER (7) makes a good seal and retains
water in Sink. If DRAIN STOPPER (7) does not seal properly, please refer to Troubleshooting section in these instructions.
• Release POP-UP KNOB (6) down and check all drain connections and “P” trap for leaks. Tighten if necessary.
TEST INSTALLED FITTING
6
3
4
1
5
OFF
ON
HOT
COLD
“P” TRAP
WASTE
OUTLET
2
2
7

- 6 - M965700 Rev. 1.1 (4/17)
• Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.
• Look at the area on the Drain Body where the Cable was attached and locate the component labeled as
“Cam” in the illustration. Fig. B.
• Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go. At this point the
Stopper should be in the UP position. Fig. B, C.
• Push DOWN on the Lift-Knob to make sure it is fully down. Fig. C.
• Re-attach the Cable to the Drain Body Connection (2) by threading the Cable Connector (1) clockwise onto the
Drain Body Connection (2) and hand-tighten. Fig. A.
• Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.
• Look at the area on the Drain Body where the Cable was attached and locate the component labeled
as “Cam” and “Cam Cap” in the illustration. Fig. B.
• Use ngers or small screwdriver under either side of the Cam Cap to pry it out from the Drain. Fig. D.
• Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig. E.
• The Stopper can now be removed by lifting it out of the Drain. Fig. F.
If sink does not hold water even though Stopper is in the “down” position:
• Follow CABLE ADJUSTMENT PROCEDURE.
If Stopper does not raise up fully or sink drains too slowly:
• Follow CABLE ADJUSTMENT PROCEDURE.
If you need to remove the Stopper:
• Follow STOPPER REMOVAL PROCEDURE.
If you would like the ability to remove your Stopper simply by lifting it out of the drain:
• Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
CABLE ADJUSTMENT PROCEDURE
STOPPER REMOVAL PROCEDURE
Speed Connect®Drain
Troubleshooting Guide
CAM
CAM CAP
Fig. B.Fig. A.
REMOVE
CAM
Fig. E. Fig. F.
2
1
RE-ATTACH
DISCONNECT
Fig. D.
REMOVE
CAM CAP
Fig. C.
DOWN
STOPPER
CAM
CAM CAP
Fig. B.Fig. A.
REMOVE
CAM
Fig. E. Fig. F.
2
1
RE-ATTACH
DISCONNECT
Fig. D.
REMOVE
CAM CAP
Fig. C.
DOWN
STOPPER

- 7 -
Fig. J. Fig. K.
INSTALL
CAM CAP
CAM
INSTALL CAM
Unlocked Mode
DRAIN
Fig. G.
LOOP TOWARD
REAR OF BIDET
180˚
DRAIN
Fig. H.
LOOP TOWARD
FRONT OF BIDET
Locked Mode
(Vandal Proof)
M965700 Rev. 1.1 (4/17)
LOCKED MODE:
• Look at the Plastic Loop at the bottom of the Stopper and notice
that the Loop is on one side of the Stopper. Fig. G.
• To install the stopper in “Locked” mode, insert the Stopper into
the Drain so that the Plastic Loop is facing toward the rear of the
Sink. Rotate Stopper slightly if necessary so that the Stopper slides
all the way down. Fig. G.
• Re-install the Cam into the Drain, rotating the Cam if necessary
to make sure it is fully inserted. Fig. J.
• Re-install the Cam Cap, making sure the guide teeth are facing
outward. If the Cam Cap does not “snap” into place, then rotate
the Cam to make sure it is fully inserted. Fig. K.
• Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in
Troubling Shooting Guide to complete installation. Stopper will be
in “Locked” mode and not be removable.
UNLOCKED MODE:
• Look at the Plastic Loop at the bottom of the Stopper and notice
that the Loop is on one side of the Stopper. Fig. H.
• To install the stopper in “Unlocked” mode, insert the Stopper into
the Drain so that the Plastic Loop is facing toward the front of the
Sink. Rotate Stopper slightly if necessary so that the Stopper slides
all the way down. Fig. H.
• Re-install the Cam into the Drain, rotating the Cam if necessary
to make sure it is fully inserted. Fig. J.
• Re-install the Cam Cap, making sure the guide teeth are facing
outward. If the Cam Cap does not “snap” into place, then rotate
the Cam to make sure it is fully inserted. Fig. K.
• Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in
“Troublingshooting Guide” to complete installation. Stopper will be
in “Unlocked” mode and removable.
STOPPER INSTALLATION PROCEDURE
The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed)
or “Unlock” Mode (Stopper is removable).

- 8 -
M964524-YYY0A
POP-UP ROD
AND KNOB
M964554-YYY0A
SET SCREW
A860601.191
SEALING WASHER
A962294.191
AERATOR
ASSEMBLY
D35100100
D35100150
A860610.191
MOUNTING KIT
M964811-0070A
FLOW CONTROL
A860606.191
CARTRIDGE
M952430-0070A
CABLE ASSEMBLY
A860602.XXX
HANDLE
M952425.XXX
DRAIN
ASSEMBLY
M921935-0070A
ADAPTOR
M965700 Rev. 1.1 (4/17)
Replace the “YYY” with
appropriate finish code
POLISHED CHROME 100
BRUSHED NICKEL 144
MODEL NUMBER
MODEL NUMBER
D3510010C
D3510015C
Rem®
Single Lever
Monoblock Faucet
Single Lever
Vessel Faucet
D3510010C
D3510015C