DXV Victorian D35402300 User manual

- 1 -
INSTALLATION INSTRUCTIONS
SAVE FOR FUTURE USE
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2017
RECOMMENDED TOOLS AND MATERIALS
Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing
supply stores. It is essential that the tools and materials be on hand before work has begun.
M965538 Rev. 1.6 (4/17)
Model D35402300
Victorian
Single Control Kitchen Faucet
with Pull-Down Spray
ROUGHING-IN DIMENSIONS:
• For reference
Plumbers' Putty or CaulkingAdjustable Wrench
Phillips Screwdriver
Channel Locks Flat Blade Screwdriver
NOTE: Bore hole size is 1-3/8"
SPRAY HOSE
WEIGHT
17-21/32"
(451 mm)
9-9/32"
(235 mm)
3/8"
COMPRESSION
2-1/4" D.
(57 mm)
8-3/32"
(210 mm)
2-3/16"
(53.8 mm)
In the United States:
DXV
One Centennial Avenue
Piscataway, New Jersey 08855
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.DXV.com
In Canada:
DXV
5900 Avebury Road
Mississauga, Ontario
L5R 3M3
Canada
Toll Free: 1-800-387-0369
Local: 905-306-1093
Fax: [phone]
www.DXV.ca
In Mexico:
DXV
Via Morelos 330
Col. Santa Clara Coatitla
Ecatepec, Estado de México 55540
Toll Free: 01-800-8391200
www.DXV.mx
Thank you for selecting DXV. To ensure that your
installation proceeds smoothly, please read these
instructions carefully before you begin.

- 2 - M965538 Rev. 1.6 (4/17)
1INSTALL FITTING
• Make certain the O-RING (2) is properly seated in recess of FAUCET BASE (3).
• Insert HOSES (4) and SHANK (9) through center hole of sink or mounting surface.
• Assemble three BRASS SCREW (8) into the FIXATION RING (7).
• Assemble SUPPORT PLATE (5) METAL WASHER (6), and
FIXATION RING (7) onto SHANK (10) from underside of sink.
Hand tighten the FIXATION RING (7) and check that
FAUCET (1) is centered.
• Use a screwdriver to tighten SCREWS (8) on FIXATION RING (7).
Work your way around FIXATION RING (7), tightening the SCREWS (8)
slightly each time until all are snug to ensure even pressure.
CAUTION Turn off hot and cold wate
supplies before beginning.
5
86
7
4
9
2
3
1

- 3 -
6
7
1
4
5
2
3
SUPPLY STOPS
HOT
COLD
M965538 Rev. 1.6 (4/17)
4
3
TEST INSTALLED FAUCET
MAKE WATER SUPPLY CONNECTIONS
• Move HANDLE (1) into “off” position.
• Turn on water supplies and check all connections for leaks.
• Pull HAND SPRAY (2) from HOLDER (3) and disconnect
HAND SPRAY (2). Pull HOSE (4) (HOSE should pull
approximately 2 feet) and direct open HOSE END (4) into sink.
• Operate handle, in COLD and HOT positions,
to ush water lines thoroughly.
• Connect HAND SPRAY (2) to HOSE END (4).
Place HAND SPRAY (2) back into faucet, operate
HANDLE (1) and check all connections for leaks.
• Check HAND SPRAY (2) operation, with
faucet on push front of LEVER (5) for
a broad cleansing spray.
TROUBLE SHOOTING
Low water flow from faucet:
• Remove check valve assembly and check
fordebris. Clean if necessary.
• Remove back ow preventer from spray head
and clean if necessary.
• Remove AERATOR (6) and clean if necessary.
Pull-Out Spray will not remove from faucet freely:
• Check that pull-out spray hose is not obstructed with
plumbingconnections or ttings under faucet.
• Make sure hose is not twisted or bound in faucet body.
• Turn off hot and cold water supplies before beginning.
• Connect FLEXIBLE SUPPLIES (6, 7) directly to wall supplies.
Connection on tting supplies are 3/8" compression. Connect
left supply (Marked Red) to Hot and right supply (Marked Blue)
to Cold wall supply. Use adjustable wrench to tighten connections.
Do not over tighten.
• Faucet supplies are 21" long from faucet base.
Note: If additional supply length is required, installer must
purchaseadditional parts separately.
Important: If SUPPLY HOSES (6, 7) are too long,
loop asillustrated to avoid kinking.
2CONNECT SPRAY HOSE
• Slide COUPLING NUT (1) of SPRAY HOSE (2) onto end of OUTLET (3).
Tighten with wrenchesto make a water tight connection.
• With HAND SPRAY seated in faucet body,install WEIGHT (4) onto HOSE (2)
using two SCREWS (5). Locate the WEIGHT (4) two feet (2') from the underside
of the sink deck.Tighten SCREWS (5) rmly.
CHECK
CONNECTIONS
FOR LEAKS
2
5
6
1
3
4

- 4 - M965538 Rev. 1.6 (4/17)
Replace the “YYY” with
appropriate finish code
POLISHED CHROME 100
CARBON BRONZE 110
ULTRA STEEL 355
Victorian
Single Control
Kitchen Faucet
with Pull-Down Spray
MODEL NUMBER
D35402300
M964395-0070A
WEIGHTS
H962078.191
CARTRIDGE NUT
H961342.XXX
HANDLE KIT
H962019.XXX
HANDLE FIXATION
M964406-0070A
CARTRIDGE
M964665-YYY0A
SPOUT SUB-ASSEMBY
M964669-YYY0A
ESCUTCHEON KIT
M964667-0070A
MOUNTING KIT
M964745-YYY0A
PULL DOWN SPRAY
M964668-YYY0A
DECORATIVE RING KIT
M964967-1000A
NYLON SPRAY HOSE
WITH SEALS