DXV Rem D35100510 User manual

- 1 -
INSTALLATION INSTRUCTIONS
SAVE FOR FUTURE USE
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2017 M965498 Rev. 1.3 (5/17)
Model D35100510
To be used with
D35000510.191 - 1/2"Thermostatic Mixing Valve
D35000530.191 - 3/4"Thermostatic Mixing Valve
Rem®
1/2"(13 mm) & 3/4"(19 mm)
Thermostatic Mixing Valve Trim Kit
Flat Blade ScrewdriverPhillips Screwdriver
FINISHED WALL
6-5/8"
(168 mm)
8-3/8"
(213 mm)
2" to 3"
(51 mm to 76 mm)
1-7/8"
(48 mm)
RECOMMENDED TOOLS AND MATERIALS
Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing
supply stores. It is essential that the tools and materials be on hand before work is begun.
ROUGHING-IN DIMENSIONS:
• For reference
100
In the United States:
DXV
One Centennial Avenue
Piscataway, New Jersey 08855
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.DXV.com
In Canada:
DXV
5900 Avebury Road
Mississauga, Ontario
L5R 3M3
Canada
Toll Free: 1-800-387-0369
Local: 905-306-1093
Fax: [phone]
www.DXV.ca
In Mexico:
DXV
Via Morelos 330
Col. Santa Clara Coatitla
Ecatepec, Estado de México 55540
Toll Free: 01-800-8391200
www.DXV.mx
Thank you for selecting DXV. To ensure that your
installation proceeds smoothly, please read these
instructions carefully before you begin.

- 2 - M965498 Rev. 1.3 (5/17)
1
2TRIM INSTALLATION
TEMPERATURE CALIBRATION
• Unscrew PLASTER GUARD SCREWS and remove PLASTER GUARD.
• Check that arrow marking “B” points vertically upwards. If not, push the BLACK CLAMP on the SECURING RING to
the right, pull off KNOB MOUNT and reinstall KNOB MOUNT with| arrow “B” pointing upwards.
• The maximum mixed water temperature is set at 109˚ F (43° C) at the factory. This setting can be changed if desired.
• Remove the TEMPERATURE LIMIT STOP (H shaped Black Plastic part). Re-install it at the desired notch as indicated in the
diagram to limit the maximum mixed water temperature to 104˚F or 112˚F.
• For 100˚F adjustment, turn the water supply on. Turn KNOB MOUNT until the spout temperature is 100˚F. Check that arrow
marking “A” on the KNOB MOUNT still points upward after adjusting the thermostat to 100˚F. If not, pull out the RED
LOCKING DEVICE. Remove KNOB MOUNT by pulling it towards you while standing directlyin front of the valve.
• Reinstall the KNOB MOUNT so that the arrow marking “A” points upwards.
• Reinstall RED LOCKING DEVICE.
KNOB
MOUNT
ARROW
"A"
BLACK
CLAMP
ARROW
"B"
RED LOCKING
DEVICE
SECURING
RING
TEMPERATURE
LIMIT STOP 104°F
(40°C)
109°F
(43°C)
112°F
(44.4°C)
• Push CAP (1) over the O-RING SEAL (2).
• Push ESCUTCHEON HOLDER and SEAL (3) with lightly greased O-ring seal over CAP (1) and secure with SCREWS (4).
• Align PINS (6) on back side of ESCUTCHEON (5) with the HOLES (7) in ESCUTCHEON HOLDER (3) and press
ESCUTCHEON (5) ush against nished wall.
2
1
7
7
3
4
GREASE
ESCUTCHEON
HOLDER
O-RING SEAL
4
6
5

- 3 - M965498 Rev. 1.3 (5/17)
3
4
HANDLE INSTALLATION
OPERATING THE VALVE
• If a temperature over 100°F is desired, push the STOP
BUTTON (1) down and turn the TEMPERATURE KNOB (2).
• This will increase the mixed water temperature up to the
maximum limit previously selected in step 1.
• Push TEMPERATURE-CONTROL KNOB (1) onto KNOB MOUNT (2).
• Attach TEMPERATURE CONTROL KNOB (1) to valve with ATTACHMENT SCREW (3). Push HANDLE (4) onto
TEMPERATURE CONTROL KNOB (1).
• Tighten SET SCREW (5) with HEX WRENCH (6) to secure HANDLE (4).
6
5
100
2
1
34
100
1
2

Rem®
1/2"(13 mm) & 3/4"(19 mm)
Thermostatic Mixing
Valve Trim KIT
M965498 Rev. 1.3 (5/17)
- 4 -
Replace the “YYY” with
appropriate finish code
POLISHED CHROME 100
BRUSHED NICKEL 144
D35100510
MODEL NUMBER
100
H960680.XXX
THERMO CARTRIDGE
COVER
H961281.XXX
TRIM PLATE
A860821.XXX
HANDLE ADAPTER
A860822.XXX
HANDLE
A961057.191
SET SCREW
H961241.191
TRIM PLATE HOLDER
H960892.191
HANDLE EXTENSION KIT
A860826.191
ESCUTCHEON SCREWS