DXV Percy D35105104 User manual

- 1 -
INSTALLATION INSTRUCTIONS
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2017
SAVE FOR FUTURE USE
RECOMMENDED TOOLS AND MATERIALS
Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing
supply stores. It is essential that the tools and materials be on hand before work is begun.
M965530 Rev. 1.5 (10/17)
Loop Handle Lavatory
Models D35105104, D35105104RB
Pixie Handle Lavatory
Models D35105100 , D35105100RB
Loop Handle Vessel
Models D35105154, D35105154RB
Pixie Handle Vessel
Models D35105150, D35105150RB
Percy®
Single Control Lavatory
and Vessel Faucet
ROUGHING-IN DIMENSIONS:
• For reference
Adjustable WrenchFlat Blade Screwdriver Channel Locks
NOTE: MOUNTING HOLE 1-1/4" (32 mm) D.
MOUNTING
SURFACE
20"
(508mm)
FLEXIBLE
HOSES
9-9/16"
(243 mm)
6-3/4"
(171 mm)
8-13/16"
(223 mm)
3-5/8"
(92 mm)
1-1/2"
(38 mm) MAX.
2-1/4"
(57 mm)
1-1/4" OD
(32 mm OD)
12-1/2"
(318 mm)
4-1/2"
(114 mm)
2-7/16"
(63 mm) D.
LOOP
HANDLE
PIXIE
HANDLE
14-7/8"
(378 mm)
14-1/8"
(359 mm)
6-3/4"
(171 mm)
8-15/16"
(227 mm)
2-1/4"
(57 mm)
4-1/2"
(114 mm)
SUPPLY CONNECTIONS ARE 3/8" COMPRESSION
2"
(51 mm) MAX.
In the United States:
DXV
One Centennial Avenue
Piscataway, New Jersey 08855
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.DXV.com
In Canada:
DXV
5900 Avebury Road
Mississauga, Ontario
L5R 3M3
Canada
Toll Free: 1-800-387-0369
Local: 905-306-1093
Fax: [phone]
www.DXV.ca
In Mexico:
DXV
Via Morelos 330
Col. Santa Clara Coatitla
Ecatepec, Estado de México 55540
Toll Free: 01-800-8391200
www.DXV.mx
Thank you for selecting DXV. To ensure that your installation proceeds
smoothly, please read these instructions carefully before you begin.

- 2 - M965530 Rev. 1.5 (10/17)
1
• Seat O-RING SEAL (1) into under side of FAUCET BASE (2).
• Feed FAUCET SUPPLIES (3), MOUNTING STUD (4) and DRAIN CABLE ASSEMBLY (8) through the mounting hole of lavatory
or mounting surface. Fig. A.
• From below, push GASKET (7) and RETAINING WASHER (5) onto MOUNTING STUD (4). Secure Faucet with MOUNTING
NUT (6), pulling faucet to front of sink, so SUPPLIES (3) rests against mounting hole. Before nal tightening, make sure collar
on MOUNTING NUT (6) is seated into RETAINING WASHER (5).Fig. B.
• Adjust Faucet so that it is centered. Tighten MOUNTING NUT (6) to complete faucet mounting.
INSTALL FAUCET
CAUTION Turn off hot and cold water
supplies before beginning.
8
2
43
1
GROOVE
(FAUCET BASE)
MOUNTING SURFACE
Fig. A.
COLLAR ON
MOUNTING NUT
6
4
7
5
Fig. B.

- 3 - M965530 Rev. 1.5 (10/17)
2
3
4
6
5
POP-UP DRAIN
REMOVE MOUNTING WASHERS
AND LOCKNUT
ATTACH DRAIN FROM
BELOW FIXTURE
FLANGE GASKET AND POP-UP KNOB
TIGHTEN LOCKNUT
• Remove CLEAR PLASTIC COVER (1). Fig. A.
• Remove FOAM SPACER (2) from
under DRAIN POP-UP (3). Fig. A.
• Tighten TAILPIECE (4) on DRAIN BODY
before installing DRAIN BODY. Fig. B.
• Thread LOCKNUT (1) counter-clockwise
and remove from drain body. Remove
PLASTIC WASHER (2) and pull off
RUBBER CONE WASHER (3) Fig. A.
• Drop DRAIN BODY (4) through sink drain
hole. Make sure WHITE FOAM GASKET (5)
is under ange of DRAIN BODY (4). Fig. B.
Note: No plumber’s putty or caulk is required.
• The CABLE ATTACHMENT POINT (6) must
face towards the rear of the SINK. Fig. B.
• From under side of SINK install
RUBBER CONE WASHER (3),
PLASTIC WASHER (2) and
LOCKNUT (1) onto DRAINBODY (4).
Note: The CABLE ATTACHMENT
POINT (5) must face towards
the rear of the SINK.
• Check DRAIN FLANGE in SINK to ensure that
WHITE FOAM GASKET (3) is fully compressed
and not visible. Fig. A.
• POP-UP KNOB (1) must be fully down. Fig. B.
2
3
1
DRAIN
BODY
4
Fig. A. Fig. B.
Fig. A. Fig. B.
REAR OF
SINK
4
5
6
SINK
DRAIN
HOLE
1
3
2
Fig. A. Fig. B.
WHITE FOAM
GASKET
NOT VISIBLE DRAIN
FLANGE
DOWN
UP
1
1
5
3
2
4
1
• Tighten LOCKNUT (1) rmly with
Adjustable Wrench or Channel Locks.

- 4 - M965530 Rev. 1.5 (10/17)
7
8
9
ATTACH CABLE CONNECTOR
CHECK OPERATION OF POP-UP
MAKE WATER SUPPLY AND WASTE CONNECTIONS
• Thread CABLE CONNECTOR (1) clockwise
onto DRAIN BODY CONNECTION (2) and
hand tighten. Fig. A.
• Your new POP-UP DRAIN installation is
now complete. Fig. B.
Note: Tailpeice on pop-up drain is
1-1/4" (32 mm) O.D. Fig. B.
• Operate LIFT KNOB (1) to verify that STOPPER (2)
opens and closes.
Note: If STOPPER (2) does not open and close properly then
refer to the “troubleshooting section” of these instructions.
• Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies.
Connection on tting supplies are 3/8" (10 mm) compression. Connect
SUPPLY SUPPLY (1) (Marked with a Red Band) to the Hot wall valve
and SUPPLY HOSE (2) (Marked with a Blue Band) to the
Cold wall valve.
• Faucet supplies are 20” long from faucet base.
Note: If additional supply length is required, installer must
purchase additional parts separately.
Important: If SUPPLY HOSES (1, 2) are to long, loop as
illustrated to avoid kinking.
• Connect 1-1/4" O.D. (32 mm) tailpiece on POP-UP DRAIN to
waste outlet.
2
1
1-1/4” O.D.
Fig. A. Fig. B.
1
2
1
APPROX.
20" (508 mm)
2
COLD
HOT
3/8" COMPRESSION
1

- 5 - M965530 Rev. 1.5 (10/17)
11 CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
10
• With HANDLE (1) in OFF position, remove AERATOR (3). Turn on WATER SUPPLIES (2) and check all connections for leaks.
• Operate HANDLE (1) to ush water lines thoroughly. Replace AERATOR (3).
CHECK DRAIN CONNECTIONS
• Operate POP-UP KNOB (4) and ll lavatory with water. Check that DRAIN STOPPER (5) makes a good seal and retains
water in sink. If DRAIN STOPPER (5) does not seal properly, please refer to Troubleshooting section in these instructions.
• Release POP-UP KNOB (4) down and check all drain connections and “P” trap for leaks. Tighten if necessary.
TEST INSTALLED FITTING
3
1OFF
ON
COLD
HOT
5
“P” TRAP
WASTE
OUTLET
2
2
4

- 6 - M965530 Rev. 1.5 (10/17)
• Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.
• Look at the area on the Drain Body where the Cable was attached and locate the component labeled as
“Cam” in the illustration. Fig. B.
• Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go. At this point the
Stopper should be in the UP position. Fig. B, C.
• Push DOWN on the Lift-Knob to make sure it is fully down. Fig. C.
• Re-attach the Cable to the Drain Body Connection (2) by threading the Cable Connector (1) clockwise onto the
Drain Body Connection (2) and hand-tighten. Fig. A.
• Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.
• Look at the area on the Drain Body where the Cable was attached and locate the component labeled
as “Cam” and “Cam Cap” in the illustration. Fig. B.
• Use ngers or small screwdriver under either side of the Cam Cap to pry it out from the Drain. Fig. D.
• Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig. E.
• The Stopper can now be removed by lifting it out of the Drain. Fig. F.
If sink does not hold water even though Stopper is in the “down” position:
• Follow CABLE ADJUSTMENT PROCEDURE.
If Stopper does not raise up fully or sink drains too slowly:
• Follow CABLE ADJUSTMENT PROCEDURE.
If you need to remove the Stopper:
• Follow STOPPER REMOVAL PROCEDURE.
If you would like the ability to remove your Stopper simply by lifting it out of the drain:
• Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
CABLE ADJUSTMENT PROCEDURE
STOPPER REMOVAL PROCEDURE
Speed Connect®Drain
Troubleshooting Guide
REMOVE
CAM
Fig. E.Fig. D.
REMOVE
CAM CAP
CAM
CAM CAP
Fig. B.Fig. A.
2
1
RE-ATTACH
DISCONNECT
Fig. F.
Fig. C. DOWN
1
REMOVE
CAM
Fig. E.Fig. D.
REMOVE
CAM CAP
CAM
CAM CAP
Fig. B.Fig. A.
2
1
RE-ATTACH
DISCONNECT
Fig. F.
Fig. C. DOWN
1

- 7 -
Fig. J. Fig. K.
INSTALL
CAM CAP
CAM
INSTALL CAM
Unlocked Mode
Locked Mode
(Vandal Proof)
LOOP TOWARD
REAR OF SINK
LOOP TOWARD
FRONT OF SINK
DRAIN
DRAIN
Fig. H.
Fig. G.
M965530 Rev. 1.5 (10/17)
LOCKED MODE:
• Look at the Plastic Loop at the bottom of the Stopper and notice
that the Loop is on one side of the Stopper. Fig. G.
• To install the stopper in “Locked” mode, insert the Stopper into
the Drain so that the Plastic Loop is facing toward the rear of the
Sink. Rotate Stopper slightly if necessary so that the Stopper slides
all the way down. Fig. G.
• Re-install the Cam into the Drain, rotating the Cam if necessary
to make sure it is fully inserted. Fig. J.
• Re-install the Cam Cap, making sure the guide teeth are facing
outward. If the Cam Cap does not “snap” into place, then rotate
the Cam to make sure it is fully inserted. Fig. K.
• Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in
Troubling Shooting Guide to complete installation. Stopper will be
in “Locked” mode and not be removable.
UNLOCKED MODE:
• Look at the Plastic Loop at the bottom of the Stopper and notice
that the Loop is on one side of the Stopper. Fig. H.
• To install the stopper in “Unlocked” mode, insert the Stopper into
the Drain so that the Plastic Loop is facing toward the front of the
Sink. Rotate Stopper slightly if necessary so that the Stopper slides
all the way down. Fig. H.
• Re-install the Cam into the Drain, rotating the Cam if necessary
to make sure it is fully inserted. Fig. J.
• Re-install the Cam Cap, making sure the guide teeth are facing
outward. If the Cam Cap does not “snap” into place, then rotate
the Cam to make sure it is fully inserted. Fig. K.
• Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in
“Troublingshooting Guide” to complete installation. Stopper will be
in “Unlocked” mode and removable.
STOPPER INSTALLATION PROCEDURE
The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed)
or “Unlock” Mode (Stopper is removable).

- 8 -
MONOBLOCK
Faucet
M964631-YYY0A
LOOP HANDLE KIT
(D35105104, D35105154)
M964633-0070A
CARTRIDGE KIT
M964634-0070A
MANIFOLD SEAL KIT
M964712-0070A
O-RING SEAL
874214.XXX
DRAIN ASSEMBLY
M964636-0070A
AERATOR KIT
M964635-YYY0A
LIFT KNOB & ROD
(MONOBLOCK)
M964637-YYY0A
LIFT KNOB & ROD
(VESSEL)
M952430-0070A
SPPED CONNECT®
ASSEMBLY
M964638-0070A
MOUNTING KIT
M964632-YYY0A
PIXIE HANDLE KIT
(D35105100, D35105150)
Vessel
Faucet
M921935-0070A
ADAPTOR
M965530 Rev. 1.5 (10/17)
Replace the “YYY” with
appropriate finish code
POLISHED CHROME 100
BRUSHED NICKEL 144
MODEL NUMBERS
Lavatory
Loop Handle
D35105104, D35105104RB
Pixie Handle
D35105100, D35105100RB
Vessel
Loop Handle
D35105154, D35105154RB
Pixie Handle
D35105150, D35105150RB
Percy®
Single Lever Lavatory
and Vessel Faucets