DXV Percy D35105470 User manual

- 1 -
INSTALLATION INSTRUCTIONS
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2017
SAVE FOR FUTURE USE
RECOMMENDED TOOLS AND MATERIALS
Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing
supply stores. It is essential that the tools and materials be on hand before work is begun.
M965531 Rev. 1.7 (1/18)
Tri-Spoke Handle
Model D35105470
Cross Handle
Models D35105454, D35105454RB
Cylinder Handle
Models D35105450, D35105450RB
To be used with D35000450.191
Dual Control Wall Mount Lavatory Rough
Percy®
Wall-Mounted Vessel
Lavatory Faucet
ROUGHING-IN DIMENSIONS:
• For reference
Plumbers' Putty or CaulkingAdjustable Wrench
Phillips Screwdriver
Flat Blade Screwdriver
Channel Locks Teon Tape
2-3/8" D.
(60 mm)
TYP.
7/8" (22 mm)
3"
(77 mm)
8"
(203 mm) 11"
(279 mm)
CROSS
HANDLE
LEVER
HANDLE
TRI-SPOKE
HANDLE
2-1/2"
(63 mm)
1"
(26mm)
1-5/8" to 2-1/2"
(41 mm to 62 mm)
FINISHED
WALL
FINISHED WALL
8-3/8"
(213 mm)
3-3/16"
(80 mm)
7-5/8"
(194 mm)
1/2" NPT
UNION INLETS
In the United States:
DXV
One Centennial Avenue
Piscataway, New Jersey 08855
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.DXV.com
In Canada:
DXV
5900 Avebury Road
Mississauga, Ontario
L5R 3M3
Canada
Toll Free: 1-800-387-0369
Local: 905-306-1093
Fax: [phone]
www.DXV.ca
In Mexico:
DXV
Via Morelos 330
Col. Santa Clara Coatitla
Ecatepec, Estado de México 55540
Toll Free: 01-800-8391200
www.DXV.mx
Thank you for selecting DXV. To ensure that your
installation proceeds smoothly, please read these
instructions carefully before you begin.
D35105470
D35105454
D35105454RB
D35105450
D35105450RB

- 2 -
2
2
4
4
8
9
12
11
13
10
14
6
7 ESCUTCHEON
O-RING
1
3
Figure A
M965531 Rev. 1.7 (1/18)
1
2
3INSTALL HANDLE
• Remove PLASTER GUARDS and unthread ROUGH-IN NIPPLE (1).
• Inspect that SPOUT NIPPLE O-RINGS (2 & 3) are seated in the grooves of SPOUT NIPPLE (4).
• Thread SPOUT NIPPLE (4) into VALVE BODY (5). Tighten SPOUT NIPPLE (4) to VALVE BODY (5).
• Thread ESCUTCHEON MOUNT (6) onto SPOUT NIPPLE (4) until it engages the O-RING (2).
• Push the SPOUT ESCUTCHEON (8) onto ESCUTCHEON MOUNT (6) until it seats against the internal stop.
Tighten SET SCREW (9) with HEX WRENCH (12) supplied.
• Thread ESCUTCHEON (8) ush against nished wall. SET SCREWS (9 & 11)
should point down toward the oor after tightening.
• Make sure ESCUTCHEON O-RING (7) is in place. Push ESCUTCHEON (14)
onto SPOUT ESCUTCHEON (8) and ush against nished wall.
• Push SPOUT (10) with SPOUT O-RINGS (13) into ESCUTCHEON (8)
until seated against stop. Align SPOUT (10)
and tighten SPOUT SET SCREW (11)
with HEX WRENCH (12) supplied.
• Determine where the nished wall location will be. This measurement
is very important! Note: The rough-in measurement from the nished
wall is; 1-9/16" (40 mm) minimum and 2-7/16" (62 mm) maximum.
This is a 7/8" (22 mm) tolerance. See rough-in illustration.
• Secure WALL BRACKET (1) to cross brace of wall structure
at required height using six wood screws.
• Mount VALVE BODY (1) to WALL BRACKET (2) as shown. Level and tighten
SET SCREWS (3) to secure VALVE BODY (1) to WALL BRACKET (2).
• Connect HOT water supply to LEFT INLET UNION (4) and COLD water supply
to RIGHT INLET UNION (5). Pipe connections are 1/2” NPT. Use sealant or
Teon tape on pipe connections. Do not solder directly to valve body.
• With valves closed open supply lines and check for leaks. Remove
PLASTER GUARDS (6) and open both valves and check for leaks.
• Close both valves and turn off water supplies. Replace
PLASTER GUARDS (6) and nish wall construction.
INSTALL WALL BRACKET
INSTALL VALVE BODY
WOOD SCREWS
CROSS BRACE
WALL STUDS
1
16"
(406 mm)
HOT
COLD
6
6
5
4
3
2
1

- 3 - M965531 Rev. 1.7 (1/18)
4INSTALL HANDLES
5TEST INSTALLED FAUCET
• With HANDLE (1) in OFF position, turn on WATER SUPPLIES and check all connections for leaks.
• Remove AERATOR (2). First loosen aerator set screw with HEX WRENCH (3) supplied.
Pull out AERATOR (2) with AERATOR KEY (4).
• Operate HANDLES (1) to ush water lines thoroughly.
• Replace AERATOR (2) and tighten set screw.
• Slide BARREL SLEEVE WASHER (1) onto VALVE STEM (2) until WASHER (1) is on the smooth section of the VALVE STEM (2).
• Thread BARREL SLEEVE (3) onto VALVE BODY (4) and tighten.
• Make sure ESCUTCHEON O-RING (5) is in place. Slide ESCUTCHEON (6) onto BARREL SLEEVE (3) ush against nished wall.
• Align HANDLE as shown or as desired and install HANDLE ASSEMBLY (7, 7a, 7b) onto VALVE STEM (2).
• Thread HANDLE BASE (8) onto BARREL SLEEVE (3) until tight.
• Turn on the water supply. Check that the tting works correctly and does not leak.
2
4
5
6
1
7a
7
3
SMOOTH SECTION
8
8
7b
8
OFF
ON
OFF
ON
1
2

- 4 - M965531 Rev. 1.7 (1/18)
Percy®
Wall-Mounted Vessel
Lavatory Faucet
MODEL NUMBERS
Tri-Spoke Handle
D3510547
Cross Handle
D35105454 / D35105454RB
Cylinder Handle
D35105450 / D35105450RB
Replace the “YYY” with
appropriate finish code
POLISHED CHROME 100
BRUSHED NICKEL 144
H960853.191
ADAPTER
H960854.191
ADAPTER RECEIVER
M964641-YYY0A
SPOUT ESCUTCHEON KIT
M964625-YYY0A
HANDLE
ESCUTCHEON KIT
M964643-YYY0A
SPOUT BODY
M964623-YYY0A
LEVER HANDLE
M970431-YYY0A
CROSS HANDLE
H960202.XXX
EXTENSION
M964617-0070A
SET SCREW
M964636-0070A
AERATOR KIT
M964644-YYY0A
SPOUT KIT
M964646-0070A
SPOUT 0-RINGS
M964618-0070A
SET SCREW KIT
H960740.191
EXTENSION KIT
M970431-YYY0A
TRI-SPOKE HANDLE